Sime MURELLE EV HE 30 User manual

MURELLE ELITE

HE 30-35-35 T

USER INSTRUCTIONS

ENSURE THAT THESE

INSTRUCTIONS ARE LEFT

FOR THE USER AFTER

COMPLETION OF THE

BENCHMARK SECTION

PLEASE READ THE

IMPORTANT NOTICE

WITHIN THIS GUIDE

REGARDING YOUR BOILER

WARRANTY

UK Cod. 6322737A - 07/2019

199839

All descriptions and illustrations provided in this manual have been carefully prepared but we reserve the right to make

changes and improvements in our products that may affect the accuracy of the information contained in this manual.

IMPORTANT NOTICE

For the first year all of our appliances are protected by our manufacturer’s guarantee which covers both

parts and labour.

As you would expect from Sime Ltd, it is our aim to provide our valued customers with the best in after sales

and service.

To take advantage of any extended warranty offered, all you have to do is to adhere to these 3 simple condi-

tions:

• The installation must be carried out to Manufacturers/Benchmark Standards by a Gas Safe Registered

Engineer, and recorded in the installation manual.

• The appliance must be registered with both Sime Ltd and Gas Safe within 30 days of installation.

• The appliance must be serviced annually, by either Sime Ltd or a Gas Safe registered engineer- ensuring

that the Benchmark service record in the installation manual is completed.

Failure to comply with the above will result in only the 12 month warranty being offered.

In the absence of any proof of purchase, the 12 month warranty period will commence from the date of manu-

facture of the boiler as shown on the appliance data plate.

The Benchmark Scheme

Sime Ltd is a licensed member of the Benchmark Scheme which aims to improve the standards of instal-

lation and commissioning of domestic heating and hot water systems in the UK and to encourage regular

servicing to optimise safety, efficiency and performance.

Benchmark is managed and promoted by the Heating and Hotwater Industry Council.

For more information visit www.centralheating.co.uk

Please ensure that the installer has fully completed the Benchmark Checklist in the use and maintenance

section of the installation instructions supplied with the product and that you have signed it to say that you

have received a full and clear explanation of its operation.

The installer is legally required to complete a commissioning checklist as a means of complyng with the

appropriate Building Regulations (England and Wales).

All installations must be notified to Local Area Building Control either directly or through a Competent

Persons Scheme.

A Building Regulations Compliance Certificate will then be issued to the customer who should, on receipt,

write the Notification Number on the Benchmark Checklist.

This product should be serviced regularly to optimise its safety, efficiency and performance.

The service engineer should complete the relevant Service Record on the Benchmark Checklist after each

service.

The Benchmark Checklist may be required in the event of any warranty work and as supporting documen-

tation relating to home improvements in the optional documents section of the Home Information Pack.

OPERATING INSTRUCTIONS FOR THE USER

1.1 INTRODUCTION ...................................................................................................................................... 6

1.2 APPLIANCE OPERATION

1.3 OPERATING INSTRUCTIONS

1.4 ERRORS AND SOLUTIONS ..................................................................................................................... 8

1.5 MINIMUM CLEARANCES

1.6 ROUTINE SERVICING

1.7 ELECTRICAL SUPPLY ............................................................................................................................. 9

1.8 VENTILATION

1.9 SAFETY

MECHANICAL TIME CLOCK (CODE 8092228)................................................................................................... 10

DIGITAL TIME CLOCK (CODE 8092229) ............................................................................................................ 11

ANALOGIC RF TIME PROGRAMMER (CODE 8092231) ..................................................................................... 12

DIGITAL RF TIME PROGRAMMER (CODE 8092232) ......................................................................................... 13

CONTENTS

VERY IMPORTANT!

PLEASE MAKE SURE YOUR BENCHMARK CHECKLIST IN THE

INSTALLATION GUIDE, IS FILLED IN CORRECTLY.

ALL GAS SAFE REGISTER INSTALLERS CARRY A ID CARD.

THE REGISTRATION NUMBER SHOULD BE

RECORDED ON THE CHECK LIST.

YOU CAN CHECK YOUR INSTALLER IS GAS SAFE

REGISTERED BY CALLING ON 0800 408 5577

These appliances comply with the S.E.D.B.U.K. scheme, band “A”

Murelle ELITE HE 30: Gas Council number 47-283-55

Murelle ELITE HE 35: Gas Council number 47-283-56

Murelle ELITE HE 35 T: Gas Council number 41-283-43

OPERATING INSTRUCTIONS FOR THE USER

THE GAS SAFETY (INSTALLATION AND

USE) REGULATIONS 1996.

It is the law that all gas appliances

are installed by a registered person, in

accordance with the above regulations.

Failure to install appliances correctly

could lead to prosecution. It is in your

own interest, and that of safety, to ensure

that the law is complied with.

It is essential that the appliance is cor-

rectly earthed. An electricity supply of

240 V - 50 Hz fused at 3 A is required.

Read these instructions carefully before

attempting to operate the appliance.

1.1 INTRODUCTION

The Sime “MURELLE ELITE HE 30-35”

family are fully automatic, wall mounted,

room sealed, fan assisted range of com-

bination boilers.

When operating in winter mode, the

appliance provides central heating as

required and produces instantaneous hot

water upon demand. When operating in

summer mode, the central heating is

not operational however the appliance

continues to supply hot water whenever

it is required.

The Sime “MURELLE ELITE HE 35 T”

family is a fully automatic, wall mounted,

room sealed, fan assisted system boilers.

The boiler is fitted with a divertor valve

which enables the boiler to be directly

connected to a hot water cylinder.

1.2 APPLIANCE OPERATION

“MURELLE ELITE HE” - a demand of hot

water will be sensed by the appliance

detecting water flow (providing that the

flow rate is above 2 l/m - 0.5 gal/min).

The fan will start and the burner will

light at full output. If the draw off rate is

near the maximum design flow rate the

appliance will run continuously at full

output until a tap is either turned off or

the flow rate is reduced in which case

the heat output will reduce accordingly

to maintain a steady temperature.

Hot water is made available almost

immediately at the appliance outlet, but

the final temperature and time taken

for the hot water to reach a tap depends

upon the potentiometer setting, the rate

at which water is drawn off, and the

length of the pipe between the boiler and

the tap.

When the tap is turned off, the appliance

will revert to C.H. mode (if set on winter

position) otherwise the burner will be

extinguished pending the next demand

for hot water.

“MURELLE ELITE HE 30-35” &

“MURELLE ELITE HE 35 T” - a demand

for heating will be sensed by the boiler,

The pump will start, and provide suffi-

cient circulation is detected, the fan will

start and the burner will light. The heat

output will be controlled by the heating

sensor and the user interface control.

1.3 OPERATING

INSTRUCTIONS

1.3.1 Boiler ignition (fig. 24)

The first ignition of the boiler must be

carried out by qualified technical per-

sonnel. Successively, if it is necessary to

start up the boiler again, adhere strictly

to the following instructions: open the

gas tap to allow the flow of the fuel.

Move the main switch of the system to

“ON”. When fuel is fed to the boiler, a se-

quence of checks will be carried out and

the display shows the normal condition

of the functioning, always indicating the

pressure of the system. If the blue lumi-

nous bar is on, this indicates the presen-

ce of voltage.

N.B.: The first press of any key (2) act

only to illuminate the display, succes-

sive presses will be recognised to alter

the mode or value.

Winter

Press the key

of the controls (pos. 2)

to activate the winter mode functioning

(heating and D.H.W.). The display will be

as shown in the figure.

Summer

Press the key

of the controls (pos. 2)

to activate the summer mode functioning

(only the production D.H.W.).

The display will be as shown in the figure.

Fig. 24

Apre

Circuito

riscaldamento 2

Circuito

riscaldamento 3

(impianto tre

zone)

Apre

Circuito

riscaldamento 2

Circuito

riscaldamento 3

(impianto tre

zone)

Apre

Circuito

riscaldamento 2

Circuito

riscaldamento 3

(impianto tre

zone)

1.3.2 Regulation

C.H. temperature (fig. 25)

To set the temperature of the water for

heating, press the key of the controls

(2). The first time the key is pressed, the

SET of heating circuit 1 is selected. The

second time it is pressed, the SET if se-

cond zone fitted is selected. The display

will be as shown in the figure. Change the

values with the key

and

Standard visualisation will return to the

display by pressing the key again, or

after 10 seconds if no key is pressed.

Regulation of the external

sensor (fig. 25/a)

If an external sensor is installed, the

value of the output temperature is au-

tomatically chosen by the system, which

quickly adjusts the environmental tem-

perature on the basis of the external

temperature.

If you wish to change the value of the

temperature, increasing or decreasing

that calculated automatically by the elec-

tronic card, proceed as indicated in the

preceding paragraph.

The level of various correction of a value

of temperature proportional calculated.

The display will be as shown in fig. 25/a.

1.3.3 Regulation D.H.W.

temperature (fig. 26)

To set the desired temperature of the

D.H.W., press the key of the controls

(pos. 2). The display will be as shown in

the figure.

Change the values with the key

and

The display will return to the standard

visualisation by pressing the key

again, or after 10 seconds if no key is

pressed.

1.3.4 To switch off the boiler

(fig. 24)

In the case of a short absence, press the

key

of the controls (pos. 2).

The display will be as shown in the fig. 24.

In this way, leaving the electricity and

the fuel supply connected, the boiler is

protected from frost and from the pump

becoming jammed.

If the boiler is not used for a prolonged

period, it is advisable to disconnect the

electricity supply, by switching off the

main switch of the system, and to clo-

se the gas tap and, if low temperatures

are expected, to completely empty the

hydraulic circuits to avoid pipes being

broken by the formation of ice in the pi-

pes.

Apre

Circuito

riscaldamento 2

Circuito

riscaldamento 3

(impianto tre

zone)

Fig. 25

Apre

Circuito

riscaldamento 2

Circuito

riscaldamento 3

(impianto tre

zone)

Apre

Circuito

riscaldamento 2

Circuito

riscaldamento 3

(impianto tre

zone)

Fig. 26

Fig. 25/a

Heating circuit 2

1.4 ERRORS AND SOLUTIONS

When there is a functioning error, the di-

splay shows an alarm and the blue lumi-

nous bar becomes red.

Descriptions of the errors with the relati-

ve alarms and solutions are given below:

– ALL 01 (fig. 27)

Seek help and advice from a qualified

engineer.

– ALL 02 (fig. 27/a)

If the system pressure detected is lo-

wer than 0.5 bar, the boiler will stop

and the display will show “ALL 02”. To

proceed increase the system pressure

to between 1 and 1.5 bar using the fil-

ling loop.

– ALL 03

The system pressure detected is

more than 2.8 bar. Ensure that the

filling loop is turned off and the pipe

detatched. Lower the system pressu-

re by draining from a radiator.

If problem persists seek help from a

qualified engineer.

– ALL 04

Seek help and advice from a qualified

engineer.

– ALL 05

Seek help and advice from a qualified

engineer.

– ALL 06 (fig. 27/c)

Press the key

of the controls (2)

to re-start the boiler.

If the error persists seek help and

advice from a qualified engineer.

– ALL 07 (fig. 27/d)

Press the key

of the controls (2)

to re-start the boiler.

If the error persists seek help and

advice from a qualified engineer.

– ALL 08

Seek help and advice from a qualified

engineer.

– ALL 09

If the boiler detects inadequate sy-

stem water circulation, the boiler will

stop and display AL 09. Ensure that

at least one radiator is turned on and

that all isolation valves are open.

If problem persists it could be due to

a blocked filter within the boiler, seek

help and advice from a qualified engi-

neer.

– ALL 10

Seek help and advice from a qualified

engineer.

– ALL 13 (fig. 27/e)

Press the key

of the controls (2)

to re-start the boiler.

If the error persists seek help and

advice from a qualified engineer.

– ALL 14

Seek help and advice from a qualified

engineer.

– ALL 15

Seek help and advice from a qualified

engineer.

– From “ALL 20” to “ALL 29”

Request assistance from qualified

technical personnel.

1.5 MINIMUM CLEARANCES

The following MINIMUM CLEARANCES

must be available for servicing the appli-

ance:

1.6 ROUTINE

SERVICING

To ensure continued efficient operation

of the appliance, and as a condition of

the warranty, the boiler must be serviced

annually.

It is the law that any service work must

be carried out by a Gas Safe Register

Apre

Circuito

riscaldamento 2

Circuito

riscaldamento 3

(impianto tre

zone)

Apre

Circuito

riscaldamento 2

Circuito

riscaldamento 3

(impianto tre

zone)

Fig. 27

Fig. 27/a

Apre

Circuito

riscaldamento 2

Circuito

riscaldamento 3

(impianto tre

zone)

Apre

Circuito

riscaldamento 2

Circuito

riscaldamento 3

(impianto tre

zone)

Fig. 27/d

Apre

Circuito

riscaldamento 2

Circuito

riscaldamento 3

(impianto tre

zone)

Apre

Circuito

riscaldamento 2

Circuito

riscaldamento 3

(impianto tre

zone)

Fig. 27/e

OPEN Filling loop

Apre

Circuito

riscaldamento 2

Circuito

riscaldamento 3

(impianto tre

zone)

Apre

Circuito

riscaldamento 2

Circuito

riscaldamento 3

(impianto tre

zone)

Fig. 27/c

For servicing

ABOVE THE

APPLIANCE CASING 200 mm

AT THE R.H.S. 15 mm

AT THE L.H.S. 15 mm

BELOW THE

APPLIANCE CASING 200 mm

IN FRONT OF THE

APPLIANCE 500 mm

registered engineer.

Ensure that the service is recorded in the

installation guide use and maintenance

section.

1.7 ELECTRICAL SUPPLY

THIS APPLIANCE MUST BE EARTHED.

The mains supply must be fused at 3

amp.

1.8 VENTILATION

If the appliance is installed in a cabinet,

it MUST NOT be used for storage pur-

poses. Any ventilation provided for the

appliance during installation MUST NOT

be blocked and a periodic check must be

made to ensure that the vents are free

from obstructions.

1.8.1 Cleaning

Use only a damp cloth and mild deter-

gent to clean the appliance outer casing.

DO NOT use abrasive cleaners.

1.9 SAFETY

It is essential that the instructions in

this booklet are strictly followed for the

safe and economical operation of this

appliance. The appliance functions as a

fan assisted balanced flue unit.

The flue terminal

MUST NOT BE OBSTRUCTED under any

circumstances. If damaged, turn off the

appliance and consult the installer, ser-

vice engineer, or gas supplier.

If it is known or suspected that a fault

exists on the appliance it MUST NOT be

used until the fault has been rectified by

a competent person.

WARNING:

IF A GAS LEAK IS SUSPECTED OR

EXISTS, TURN OFF THE GAS SUPPLY TO

THE APPLIANCE AT THE GAS SERVICE

COCK.

DO NOT OPERATE ANY ELECTRICAL

SWITCHES.

DO NOT OPERATE ANY ELECTRICAL

APPLIANCE.

OPEN ALL WINDOWS AND DOORS. DO

NOT SMOKE.

EXTINGUISH ALL NAKED LIGHTS.

CONTACT THE NATIONAL GAS

EMERGENCY SERVICE IMMEDIATLEY

ON 0800111999.

Setting the time

The time of day can be set by grasp-

ing the outer edge of the black dial

and turning it in a clockwise direc-

tion until the correct time is in line

with the white pointer.

Setting the “switching time”

The “ON” periods are set by sliding

the blue tappets, adjacent to the

time periods required, to the outer

edge of the dial.

The tappets that remain at the cen-

tre of the dial will be the “OFF”

periods.

N.B.: The smallest switching time

(ON or OFF) is 15 minutes.

– To select “Timed” mode move the

selector switch in the middle of

the clock face to the “ ” posi-

tion.

– To select “Constant” mode move

the selector switch in the middle

of the clock face to the “I” posi-

tion.

– To select “OFF” mode move the

selector switch in the middle of

the clock face to the “O” position.

MECHANICAL TIME CLOCK - Code 8092228

MECHANICAL 24 hr VERSION

Slide blue tappets

OUT for ON period

Slide blue tappets IN for OFF period

Mode selector switch

DIGITAL 7 DAY VERSION

Selects da

or da

groups for real time and programme time

Selects ON/OFF permanently when in real time (advance)

Reset

Selects programming

mode

Selects mode for

setting real time of day

Winter/Summer time

± 1 hr selector

Selects hours/minutes

for time of day

and programme times

Boiler ON (I)

PROGRAMMED

Boiler

Boiler OFF (O)

Other manuals for MURELLE EV HE 30

This manual suits for next models

Table of contents

Other Sime Boiler manuals

Sime

Sime MURELLE GREEN PLANET 50 HE I User manual

Sime

Sime Planet Dewy 60 BFR User manual

Sime

Sime 2R HE Series User manual

Sime

Sime Dewy Equipe P100 Box User manual

Sime

Sime MURELLE EQUIPE 220 ErP User guide

Sime

Sime MURELLE EV 25 OF User manual

Sime

Sime Format.zip Installation instructions

Sime

Sime AQUA 25 ErP User manual

Sime

Sime MURELLE REVOLUTION 30 Manual

Sime

Sime ECOMFORT PLUS 25 HE User manual

Sime

Sime MURELLE HE 50 R User manual

Sime

Sime ALU PLUS HE 360 Manual

Sime

Sime Brava Slim HE 40 User guide

Sime

Sime Planet Dewy 60 BFR User manual

Sime

Sime DUETTO 25 EV Manual

Sime

Sime rondo User manual

Sime

Sime AQUA HE 25/25 INOX ErP.BE User manual

Sime

Sime benchmark Planet Super 4 W. M. User manual

Sime

Sime 8111235 Manual

Sime

Sime MURELLE HM ErP Series User manual

Sime

Sime ECOMAXI 160 ErP User manual

Sime

Sime Estelle HE B4 INOX ErP Manual

Sime

Sime Planet Dewy 30 User manual

Sime

Sime MURELLE HM 35 R (M) User manual

Popular Boiler manuals by other brands

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES operating instructions

Radijator

Radijator BIO max 23.1 instruction manual

Brunner

Brunner BSV 20 Instructions for use

Buderus

Buderus Logamax GB062-24 KDE H V2 Service manual

Potterton

Potterton 50e Installation and Servicing Manual

UTICA BOILERS

UTICA BOILERS TriFire Assembly instructions

Joannes

Joannes LADY Series Installation and maintenance manual

ECR International

ECR International UB90-125 Installation, operation & maintenance manual

Froling

Froling FHG Turbo 3000 operating instructions

Froling

Froling P4 Pellet 8 - 105 installation instructions

U.S. Boiler Company

U.S. Boiler Company K2 operating instructions

Henrad

Henrad C95 FF user guide

NeOvo

NeOvo EcoNox EF 36 user guide

Potterton

Potterton PROMAX SL 12 user guide

Eco Hometec

Eco Hometec EC 25 COMPACT Technical manual

Viessmann

Viessmann VITODENS 200 Operating instructions and user's information manual

Baxi

Baxi Prime 1.24 installation manual

REXNOVA

REXNOVA ISA 20 BITHERMAL Installation, use and maintenance manual