Sime Benchmark User manual

Planet Dewy

90 A - 110 A

User instructions

VERY IMPORTANT!

PLEASE MAKE SURE YOUR LOG BOOK ENCLOSED IS FILLED IN CORRECTLY.

ALL CORGI REGISTERED INSTALLERS CARRY A CORGI ID CARD.

BOTH SHOULD BE RECORDED IN YOUR CENTRAL HEATING LOG BOOK.

YOU CAN CHECK YOUR INSTALLER IS CORGI REGISTERED

BY CALLING ON 1256 3723

BOILER IGNITION (fig. 1)

Open the gas valve, lower the control

panel cover and activate the boiler by

rotating the selector knob to the summer

position ( ).

The lighting-up of the green

led ( ) will indicate that the apparatus is

switched-on and ready.

With the rotary switch in the summer

position ( ) the boiler will start-up upon

demand for domestic hot water, and run

at full power to reach the selected tempe-

rature. The gas feeding pressure will then

automatically vary to ensure that the

required temperature is kept constant.

With the rotary switch in the winter

position ( ) once the boiler has rea-

ched the value set on the heating poten-

tiometer, it will start to modulate in auto-

matically in order to supply the required

power output to the system.

The operation of the boiler will be stop-

ped through the intervention of the ther-

mostat or “Logica Remote Control”.

TIME-CLOCK INSTRUCTIONS

Setting the time

Turn the clock dial in a clockwise direction

until it reads the time of the day.

Program setting

Press inwards the segments on the pro-

gram disk corresponding to the selected

switching periods.

Function 1: segment set outwards (C.H. “ON”)

Function 2: segment set inwards (C.H. “OFF”)

Manual override

0 = “OFF” permanently

= automatic programmed operation

1 = “ON” permanently

Programming characteristics

Cycle 24 hour

Number of actions per cycle 96

Program time per segment 15 min.

Min. interval between two actions 15 min.

TEMPERATURES ADJUSTMENT (fig. 2)

The D.H.W. temperature can be adju-

sted by turning the knob of the D.H.W.

potentiometer ( ).

When there is a demand for hot water,

the set temperature is displayed on the

red led scale from 35÷80°C and the yel-

low domestic hot water led lights-up at

the same time ( ).

The C.H. temperature can be adjusted by

turning the knob of the C.H. potentiome-

ter ( ). The set temperature is indica-

ted on the red led scale from 35÷80°C

and the yellow heating led lights up at the

same time ( ).

To ensure optimal boiler efficiency at all

times, we recommend not to drop below

a minimum working temperature of 50°C.

TURNING OFF BOILER (fig. 1)

To turn off the boiler set the switch to

USER INSTRUCTIONS

WARNINGS

In case of fault and/or incorrect equipment operation, deactivate it, without making any repairs or taking any direct

action. Contact an authorised technical staff.

The installation of the boiler and any servicing or maintenance job must be carried out by qualified personnel. Under

no circumstances, the devices sealed by the manufacturer can be tampered with.

It is absolutely prohibited to block the intake grilles and the aeration opening of the room where the equipment is

installed.

LIGHTING AND OPERATION

REMOTE

CONTROL

APRE

SPIA VERDE

Fig. 1

GREEN LED

OPEN

“OFF” and close the gas-feeding pipe tap

if the boiler remains inoperative for a long

period

CLEANING AND MAINTENANCE

It is advisable that the boiler is serviced

after 12 months of operation.

Preventative maintenance and

checking of the efficient operation of

the equipment and safety devices must

be carried out by C.O.R.G.I. registered

engineers.

The boiler is supplied with an electric

cable. Should this require replacement,

contact an authorized technical staff.

FAULT FINDING

Ignition lock-out

(fig. 3)

If the burners do not ignite, the red led

will light-up

( ).

To attempt a boiler restart, rotate the

selector knob to position

()

and release

it immediately, placing it in the summer

()

or winter

()

operation position

If the boiler lock-out re-occurs, contact

an authorised technical staff.

Insufficient water pressure

(fig. 4)

If the red " .5" bar led starts flashing

the boiler will not function, to restart the

operation the system must be rechar-

ged, ask your installer to point out the fil-

ling loop and recharge the system until

the green 1 bar led lights up.

If all the leds are off, call the technical

Help Desk.

SPIA GIALLASPIA ROSSA

Fig. 2

SPIA ROSSA

Fig. 3

Fig. 4

SPIA ROSSA INTERMITTENTE

IN CONDIZIONE DI SICUREZZA

RED LED YELLOW LED

RED LED

FLASHING RED LED IN

SAFETY CONDITION

Safety thermostat trip

(fig. 5)

If the safety thermostat trips, the red

"35°C" led will start flashing. In order to

attempt a boiler restart, rotate the

selector knob to position ( ) and release

immediately, returning it to the summer

( ) or winter ( ) position.

If the boiler lock-out occurs again, call

authorised technical staff.

Other anomalies

(fig. 6)

If one of the red

“4 ÷8 °C”

leds start

flashing, switch-off the boiler and try

again.

After 2 or 3 unsuccessful attempts, do

not try again, call the technical helpdesk.

With selector CR/OFF/EST/INV/

RESET of the "PLANET DEWY 9 A-

11 A " control panel in position ( ) all

the functions are managed by the

"Logica Remote Control" regulator.

The operating instructions are reported

inside the cover (fig. 7).

Each setting or modification is displayed

(fig. 8).

LOGICA REMOTE CONTROL

KEY

1 Display

2 Info button

3 Operating mode button: automatic operation

4 Operating mode button: manual operation

5 Operating mode button: availability

6 Cover with instruction compartment

7 Temperature knob

8 Presence button Fig. 7

KEY

1 Display, time

2 Heating programme

3 Unit (%/C°)

4 Presence button display

5 External temperature

6 Ambient temperature

7 Holiday function

8 Operating mode

9 Line number/day

10 Burner on

11 Heating function

12 Domestic hot water/temperature/domestic

hot water load Fig. 8

SPIA ROSSA INTERMITTENTE

Fig. 5

Fig. 6

SPIA ROSSA INTERMITTENTE

FLASHING RED LED

If your house is too warm or too cold, you can easily correct the set tempe-

rature by adjusting the temperature knob.

Before re-correcting, allow the temperature to stabilise.

Note: The temperature knob can only be used to correct the set temperature, while the redu-

ced temperature remains unaltered.

Temperature correction

Rotating the knob towards the + sign increases the set tempera-

ture by approximately 1°C per notch.

Rotating the knob towards the sign decreases the set tempera-

ture by approximately 1°C per notch.

Before correcting the temperature on the regulator, the thermostat valve temperatures

(if provided) must be set to the required temperature first.

Each time the info button is pressed, the fol-

lowing are displayed one after the other. The

temperature sensor continues to function

independently of the display

Day, time, ambient temperature

External temperature *

Domestic hot water temperature *

* This information appears only when the

relative sensor is connected or if it is tran-

smitted by the boiler regulator.

Info button

(grey reference button)

The required operating mode is selected by

pressing the relative button with the corre-

sponding symbol. The selection is displayed

with the symbol

Automatic operation: the heating functions automatically in line with the set heating

programme. The programme can be switched-off for brief periods by pressing the

presence button.

Manual operation: the heating functions manually in line with the selection of the

presence button.

Availability: heating is deactivated.

Selection of operating mode

(grey reference buttons)

OPERATION

During operation, the cover of the controller must be kept closed.

If the rooms remain unused for long periods of time, you can reduce

the temperature with the presence button, thus saving energy.

When the rooms are occupied, they can be heated by re-pressing the

presence button.

The current selection is shown on the display:

The current selection becomes permanent in manual mode , in automatic mode it

only lasts until the next heating programme switches-in.

Presence button

Heating to the set temperature

Heating to the reduced temperature

NOTE:

In automatic mode, the apparatus switches between the set temperature and the reduced

temperature according to the timer programme. The switch-over of the temperatures in

manual mode is performed manually with the presence button.

Temperature control

Set temperature:

Temperature during occupation of the rooms

(basic setting).

Reduced temperature:

Temperature during periods of absence or at night.

Domestic hot water temperature:

Temperature required for domestic hot water.

Before correcting the temperature on the regulator, the thermostat valve temperatures

(if provided) must be set to the required temperature first.

PROGRAMMING

When programming, the regulator panel must be open.

As soon as the cover is opened,

the display and the functions of

the buttons are switched. The

number in the box indicates the

programme line and can be

selected using the arrow but-

tons.

You can set or display the following values:

• Temperature up to

• Heating programme up to

• Day of the week and time up to

• Current values up to

• Holiday length

• Return to default values

1 3

411

12 14

15 17

Heating/domestic hot

water programme

The heating programme can be used to pre-set the temperature switch-over times for one

week.

The weekly programme consists of 7 daily programmes.

One day programme allows three heating phases to be set-up. Each phase is defined by a start

and finish time.

Day programme n.8 is for domestic hot water (for setting by the heating engineer only).

If one of the phases is not necessary, enter the same start and finish times.

Holiday function For setting the number of days of absence.

The holiday symbol ( ), will appear on the display, the start day on the left (1 =

Monday / 7 = Sunday) and the number of holiday days on the right.

During the holiday period, the regulator will switch to availability mode.

When the set days have passed, the regulator will switch to automatic operation

mode.

NOTE:

The holiday function can be cancelled by pressing one of the operating mode buttons

Current values Display and setting of the slope of the characteristic heating curve. Choose a gradient

indicated at point 2.10.3 when the imposed room temperature is not reached.

Display of the current temperature in the boiler.

Display of the current burner power and operating mode ( = heating / =

domestic hot water)

Setting the time To set the day of the week

(1 = Monday / 7 = Sunday).

Setting the hour.

Setting the minutes.

The setting of the time will change when a full hour is reached.

The current time is adjusted with and keeping these buttons pressed will accele-

rate the adjustment.

Select the day required for the heating phases (1 = Monday... 7 = Sunday/8 = dome-

stic hot water programme)

Start of phase 1: heating in set mode

End of phase 1: heating in reduced mode

Start of phase 2: heating inset mode

End of phase 2: heating in reduced mode

Start of phase 3: heating inset mode

End of phase 3: heating in reduced mode

Copying a day programme

Press this button to copy the current heating programme to the next day.

Press this button to copy the current heating programme to the previous

day.

The next day is displayed as confirmation.

Default value To return the settings to their default values, press buttons and simul-

taneously for at least 3 seconds. A symbol will appear on the display as confirmation.

WARNING

The values in the following lines previously entered will be lost.

• Temperature and time programme up to

• Holiday duration

110

Error display

Ignition lock-out

Rotate selector CR/OFF/EST/INV/RESET on the "PLANET DEWY 9 A-11 A" control panel

to the release position

()

to reset operation (fig. 3).

If the lock-out re-occurs, call authorised technical staff.

Safety thermostat trip

Rotate selector CR/OFF/EST/INV/RESET on the "PLANET DEWY 9 A-11 A" control panel

to the release position

()

to reset operation (fig. 5).

If the lock-out re-occurs, call authorised technical staff.

Domestic hot water sensor fault (SS)