Silicon Laboratories EFM8BB3-SLSTK2022A User manual
UG125: EFM8BB3-SLSTK2022A User's
Guide
The EFM8BB3-SLSTK2022A is an excellent starting point to get
familiar with the EFM8 Busy Bee microcontrollers.
The kit contains sensors and peripherals demonstrating some of the MCU's many capa-
bilities. The kit can also serve as a starting point for application development.
The kit includes the following:
KEY FEATURES
• EFM8BB31F64G MCU with 64 KB Flash
and 4 KB RAM.
• 20-pin expansion header.
• Power sources include USB and CR2032
battery.
• 2 user buttons, 1 tri-color LED.
• 8-direction joystick.
• Ultra low power 128x128 pixel Memory-
LCD.
• EFM8BB3 Busy Bee Starter Kit Board
• 1 x CR2032 battery
• Getting Started card
• 1 x mini USB cable
silabs.com | Building a more connected world. Rev. 0.7
1. Getting Started
For information on getting started with the EFM8BB3-SLSTK2022A kit, including links to documentation and other resources, visit the
kit product page.
Hardware
To set up the hardware for the EFM8BB3-SLSTK2022A kit:
1. Provide power to the board by connecting the USB connector to the PC using the provided USB cable.
2. Move the switch to the Advanced Energy Monitor (AEM) position.
Figure 1.1. Hardware Setup
Software
The first step to get started with your new EFM8BB3-SLSTK2022A is to go to http://www.silabs.com/simplicity.
The Simplicity Studio software package contains all the tools, drivers, software examples and documentation needed to use the
EFM8BB3 Starter Kit. The board comes pre-loaded with a default application, Space Invaders, to interact with while the software down-
loads.
After downloading the latest version of Simplicity Studio:
1. Select the J-Link adapter for the kit under [Devices].
2. Click one of the demos available under [Getting Started]>[Demos] or click the [Getting Started]>[Demos]>[View All] to view the
entire list of available demos.
3. Click the [Space Invaders] demo and click [Start] to download and run the demo.
Additional demos showcasing the various features of the EFM8 are also available in Simplicity Studio.
UG125: EFM8BB3-SLSTK2022A User's Guide
Getting Started
silabs.com | Building a more connected world. Rev. 0.7 | 2
2. Kit Block Diagram
An overview of the EFM8BB3 Starter Kit is shown in the figure below.
ADC
Joystick
EFM8BB3
Microcontroller
POWER
Board
Controller
UART
Figure 2.1. Kit Block Diagram
UG125: EFM8BB3-SLSTK2022A User's Guide
Kit Block Diagram
silabs.com | Building a more connected world. Rev. 0.7 | 3
3. Kit Hardware Layout
The layout of the EFM8BB3 Starter Kit is shown below.
Kit USB
Connector
CR2032
Battery Holder
Power Source Select
User Push
Buttons User LED
EFM8 Reset Button
EFM8BB3 MCU
Expansion
Header
Joystick
128x128 Pixel
Memory LCD
Direct
Debug Connector
Debug IN/OUT
Connector
Reference
Board Connector
Figure 3.1. EFM8BB3-SLSTK2022A Hardware Layout
The EFM8 device on the kit is connected to several peripherals. The table below shows all of the external connections to the MCU.
Table 3.1. Kit MCU Connections
MCU Port Pin Port Pin Assigned
Function
Primary Board Connec-
tion
Secondary Board Con-
nection
Expansion Port Con-
nection (EXP)
P0.0 GPIO VREF Caps
P0.1 GPIO AGND
P0.2 Port Match Input Push Button 0 (PB0)
P0.3 Port Match Input Push Button 1 (PB1)
P0.4 UART0 TX BC - UART_TX
P0.5 UART0 RX BC - UART_RX
P0.6 SPI0 SCK DISP - SPI CLK1SPI CLK EXP8
P0.7 SPI0 MISO SPI MISO EXP6
P1.0 SPI0 MOSI DISP - SPI MOSI SPI MOSI EXP4
P1.1 SPI0 NSS SPI CS EXP10
P1.2 SMBus0 SDA I2C SDA BC - REFCLK EXP16
P1.3 SMBus0 SCL I2C SCL BC - 1 kHz SINE EXP15
P1.4 PCA0 CEX0 RGB LED0
P1.5 PCA0 CEX1 RGB LED1
P1.6 PCA0 CEX2 RGB LED2
UG125: EFM8BB3-SLSTK2022A User's Guide
Kit Hardware Layout
silabs.com | Building a more connected world. Rev. 0.7 | 4
MCU Port Pin Port Pin Assigned
Function
Primary Board Connec-
tion
Secondary Board Con-
nection
Expansion Port Con-
nection (EXP)
P1.7 ADC / CMP Joystick
P2.0 UART1 TX UART1 TX EXP12
P2.1 UART1 RX UART1 RX EXP14
P2.2 GPIO BC - Enable
P2.3 GPIO DAC LOOPBACK0 EXP3
P2.4 GPIO EXP13
P2.5 GPIO UFL ADC INPUT
P2.6 GPIO DISP - SPI CS
P3.0 GPIO DAC LOOPBACK1 EXP5
P3.1 GPIO EXP7
P3.2 GPIO EXP9
P3.3 GPIO EXP11
P3.4 GPIO DISP - Enable
P3.7 / C2D C2D (for debug)
Note:
1. This signal has high loading. If the MCU pin is used for signals where edge speed is critical, this signal should be disconnected
from the pin.
UG125: EFM8BB3-SLSTK2022A User's Guide
Kit Hardware Layout
silabs.com | Building a more connected world. Rev. 0.7 | 5
4. Power Supply and Reset
4.1 MCU Power Selection
The Busy Bee MCU on the EFM8BB3-SLSTK2022A is designed to be powered by three different sources:
• Through the on-board debugger.
• By a 3 V battery.
• By an externally supplied power source.
Selecting the power source is done with the slide switch in the lower left corner of the board. The figure shows how the different power
sources can be selected with the slide switch.
Figure 4.1. EFM8BB3-SLSTK2022A Power Switch
With the switch in the AEM position, an on-board low noise LDO with a fixed output voltage of 3.3 V is used to power the MCU. This
LDO is powered from the "J-Link" USB cable.
With the switch in the BAT position, the device may be powered from either a 20 mm coin cell battery (in the CR2032 socket) or an
external power supply (connected to the VMCU and GND pins on the expansion header).
4.2 MCU Reset
The EFM8 MCU can be reset by a few different sources:
• The RESET button.
• An external debugger by pulling the RSTb pin low.
UG125: EFM8BB3-SLSTK2022A User's Guide
Power Supply and Reset
silabs.com | Building a more connected world. Rev. 0.7 | 6
5. Peripherals
The starter kit has a set of peripherals that showcase some of the features of the EFM8 Busy Bee microcontroller.
Be aware that most EFM8 I/O routed to peripherals are also routed to the breakout pads. This must be taken into consideration when
using the breakout pads for your application.
5.1 Push Buttons and LEDs
The kit has two user push buttons. They are connected to the EFM8, and are debounced by RC filters with a time constant of 1 ms. The
buttons are connected to pins P0.2 and P0.3.
In addition to the two push buttons, the kit also features a tri-color LED that is controlled by EFM8 GPIO. The LED is connected to pins
P1.4, P1.5, and P1.6 in an active-low configuration.
Figure 5.1. Buttons/LEDs
UG125: EFM8BB3-SLSTK2022A User's Guide
Peripherals
silabs.com | Building a more connected world. Rev. 0.7 | 7
5.2 Joystick
The kit has an analog joystick with 8 measureable positions. This joystick is connected to the EFM8 on the P1.7 pin and uses different
resistor values to create voltages measurable by the ADC0.
Figure 5.2. Joystick
Table 5.1. Joystick Resistor Combinations
Direction Resistors Combinations (kΩ) Expected UIF_JOYSTICK Voltage (V)1
Center press 0.1
0.1 + 10
0.033
Up (N) 60.4
60.4 + 10
2.831
Up-Right (NE) (N// E)
(N// E) + 10 =21.34
21.34 + 10
2.247
Right (E) 33
33 + 10
2.533
Down-Right (SE) (S// E)
(S// E) + 10 =7.67
7.67 + 10
1.433
Down (S) 10
10 + 10
1.650
Down-Left (SW) (S// W)
(S// W) + 10 =6
6 + 10
1.238
Left (W) 15
15 + 10
1.980
Up-Left (NW) (N// W)
(N// W) + 10 =12.01
12.01 + 10
1.801
Note:
1. These calculated values assume a VMCU of 3.3 V.
UG125: EFM8BB3-SLSTK2022A User's Guide
Peripherals
silabs.com | Building a more connected world. Rev. 0.7 | 8
5.3 Memory LCD-TFT Display
A 1.28-inch SHARP Memory LCD-TFT has been added to the board to enable interactive applications to be developed. The display has
a high resolution of 128 by 128 pixels and consumes very little power. It is a reflective monochrome display, so each pixel can only be
light or dark, and no backlight is needed in normal daylight conditions.
The display interface consists of a SPI-compatible serial interface and some extra control signals. Data are sent to the display one line
(128 bits) at a time.
The Memory LCD-TFT display is shared with the kit Board Controller, allowing the Board Controller application to display useful infor-
mation when the user application is not using the display. The EFM8 MCU always controls ownership of the display using the
EFM_DISP_ENABLE signal:
• 0: The Board Controller has control of the display.
• 1: The user application (EFM8) has control of the display.
Data are clocked in on EFM_DISP_MOSI (P1.0) when EFM_DISP_CS (P2.6) is high, and the clock is sent on EFM_DISP_SCLK
(P0.6). The maximum supported clock speed is 1 MHz.
Refer to the display application information for details on driving the display:
http://www.sharpmemorylcd.com/1-28-inch-memory-lcd.html
0: BC controls display
1: EFM controls display
EFM_DISP_ENABLE
8
P0.6 (SPI0)
P1.0 (SPI0)
P2.6 (GPIO)
P3.4 (GPIO)
Figure 5.3. 128x128 Pixel Memory LCD
UG125: EFM8BB3-SLSTK2022A User's Guide
Peripherals
silabs.com | Building a more connected world. Rev. 0.7 | 9
6. Connectors
6.1 Breakout Pads
Many of the EFM8's pins are routed out to "breakout pads" at the top and bottom edges of the kit. A 2.54 mm pitch pin header can be
soldered in for easy access to these pins. Most I/O pins are available, with the exception of pins used to drive the LCD.
Note: Some of the breakout pads are shared by on-board EFM peripherals. The schematic must be consulted to make sure that it is
acceptable to use a shared pin in your application.
Figure 6.1. Breakout Pads and Expansion Header
UG125: EFM8BB3-SLSTK2022A User's Guide
Connectors
silabs.com | Building a more connected world. Rev. 0.7 | 10
Table of contents
Other Silicon Laboratories Microcontroller manuals
Silicon Laboratories
Silicon Laboratories C8051T622 User manual
Silicon Laboratories
Silicon Laboratories TOOLSTICK C8051F850 User manual
Silicon Laboratories
Silicon Laboratories C8051F326/7 User manual
Silicon Laboratories
Silicon Laboratories EFM32JG1 User manual
Silicon Laboratories
Silicon Laboratories C8051F30 series User manual
Silicon Laboratories
Silicon Laboratories Z-Wave 800 Series User manual
Silicon Laboratories
Silicon Laboratories C8051F31 Series User manual
Silicon Laboratories
Silicon Laboratories C8051F310-TB User manual
Silicon Laboratories
Silicon Laboratories SLWSTK6104A User manual
Silicon Laboratories
Silicon Laboratories EFR32FG23 User manual
Silicon Laboratories
Silicon Laboratories C8051F500 User manual
Silicon Laboratories
Silicon Laboratories C8051F02 Series User manual
Silicon Laboratories
Silicon Laboratories EFM32 Instruction Manual
Silicon Laboratories
Silicon Laboratories C8051F310DK-T User manual
Silicon Laboratories
Silicon Laboratories C8051F912 User manual
Silicon Laboratories
Silicon Laboratories EFR32xG21 Wireless Gecko User manual
Silicon Laboratories
Silicon Laboratories EFR32xG21 Wireless Gecko User manual
Silicon Laboratories
Silicon Laboratories C8051F530A User manual
Silicon Laboratories
Silicon Laboratories SiM3U1xx User manual
Silicon Laboratories
Silicon Laboratories EFR32MG User manual
Popular Microcontroller manuals by other brands
AMS
AMS AS7261 Demo Kit user guide
Novatek
Novatek NT6861 manual
Espressif Systems
Espressif Systems ESP8266 SDK AT Instruction Set
Nuvoton
Nuvoton ISD61S00 ChipCorder Design guide
STMicrolectronics
STMicrolectronics ST7 Assembler Linker user manual
Texas Instruments
Texas Instruments Chipcon CC2420DK user manual
Texas Instruments
Texas Instruments TMS320F2837 D Series Workshop Guide and Lab Manual
CYPRES
CYPRES CY14NVSRAMKIT-001 user guide
Texas Instruments
Texas Instruments INA-DUAL-2AMP-EVM user guide
Espressif Systems
Espressif Systems ESP8266EX Programming guide
Abov
Abov AC33M8128L user manual
Laird
Laird BL654PA user guide