Silent Alert PG3A-2204-EU User manual

Quick start guide PG3A-2204-EU

Vibrating Pager unit

CCM3A-2216-EU-PIR-MKX

MOVEMENT MONITOR 11/12/13

USE MAINS POWER SUPPLY

PS3A-2207-UK ONLY

SILENT ALERT SA3000 SYSTEM

WWW.SILENT-ALERT.CO.UK CLOFIELD LTD.UK

TEL 01246 260045

MOVE KEY DOWN

TO SWITCH ON

1 = System Code 1

2= System Code 2

3 = System Code 3

4 = System Code 4

5= Audio Monitoring

6 = Zone Multiplier (7-12)

7 = Short Audio Delay

8 = Medium Audio Delay

7 & 8 = Long Audio Delay

9 = PIR Delay 5 Mins

10= PIR Delay 10 Mins

9& 10 = PIR Delay 15 mins

11= Zone 6

12= Zone 5

13= Zone 4

14= Zone 3

15= Zone 2

16= Zone 1

MOVE KEY DOWN

TOSWITCH ON

Any questions? Call us on 01246 450789

Silent

Alert

Silent

Alert

OFF

Event Keys

Belt clip

Configuration keys

Charging Socket

OFF

Move the ON/OFF switch

to the on position (to the

right, away from off).

The pager will illuminate

each key then vibrate.

The pager is now ready

to use.

2. Install the alarm clock or trickle charger

(Part no's. CH3A-2205-IN ,

TR3A-2206-EU), insert the Pager into the

charging slot and charge for 24 hours.

The battery key on the Pager will light

green briefly upon docking confirming the

Pager is docked correctly.

If a pillow pad is fitted it will vibrate 3

times when the Pager is docked.

3. Install the Silent Alert

monitor units according

to their instructions.

4. To re-set the Pager and stop

the vibration, press and hold

the key that is lit.

Each signal will automatically

cancel after 20-40 seconds.

Smoke & CO signals will run

for 15 minutes to comply with

British standards

Silent Alert

Fire Safe

Compatible

Silent

AlertTM

5. The battery key will flash

green every 45 seconds to

indicate the Pager is

switched on.

The Pager must be recharged each night

and if not in use for more than 24 hours

should be switched off.

If the Pager becomes flat it

will vibrate and the battery

key will light up.

The battery key will flash

orange until the Pager

is recharged.

If the low battery sequence

alternates with another event

key, that monitor has a

low battery.

Silent Alert

Fire Safe

Compatible

Silent

AlertTM

We recommend a full 24 hour charge before using our equipment.

In an emergency a few hours charge may be sufficient for short time use but this is not advised.

Silent Alert

Fire Safe

Compatible

Silent

AlertTM

WARNING! Your device and its accessories are not toys. They may contain small parts. Keep them out of the reach of small children.

Silent Alert

Fire Safe

Compatible

Silent

AlertTM

12:14

SNZ

Z Z

Advanced settings PG3A-2204-EU

Vibrating Pager unit

CCM3A-2216-EU-PIR-MKX

MOVEMENT MONITOR 11/12/13

USE MAINS POWER SUPPLY

PS3A-2207-UK ONLY

SILENT ALERT SA3000 SYSTEM

WWW.SILENT-ALERT.CO.UK CLOFIELD LTD.UK

TEL 01246 260045

MOVE KEY DOWN

TO SWITCH ON

1 = System Code 1

2= System Code 2

3 = System Code 3

4 = System Code 4

5= Audio Monitoring

6 = Zone Multiplier (7-12)

7 = Short Audio Delay

8 = Medium Audio Delay

7 & 8 = Long Audio Delay

9 = PIR Delay 5 Mins

10= PIR Delay 10 Mins

9& 10 = PIR Delay 15 mins

11= Zone 6

12= Zone 5

13= Zone 4

14= Zone 3

15= Zone 2

16= Zone 1

MOVE KEY DOWN

TOSWITCH ON

Any questions? Call us on 01246 450789

Silent

Alert

OFF

With the Pager switched

on, move switch 5 to

the left

(away from the belt clip).

This will increase the range

of the Pager from 100M

(in open air),

to approximately 1000M

(in open air).

Operating Range

500M

Increasing system range

It is possible to make the Pager more sensitive when larger areas need to be covered.

Changing the system channel code

NOTE. In most cases it is not necessary to change the system code. However, when one or

more systems are in close proximity, system codes can be used to avoid interference from

other SA3000 systems using up to a maximum of 16 channels.

The Pager is supplied with no

system code switches set (system code 1).

For reference this is the factory setting

should you need to re-set the unit.

System codes can be set using

key switches 1 - 4.

The diagram to the right shows the 16

possible combinations.

Be sure that the same system code is set on

all monitors to be used in the system.

NOTE. SA3000 receivers have an ON/OFF

switch, SA3000 monitors do not.

23456 7 8

OFF

9 10 1211 13 14 15 16

OFF

Here we have a SA3000 Pager and Mini Monitor set to

system channel 2.

Ensure when setting system channel keys you remember to ignore the

Pagers ON/OFF switch or the equipment will be on different

system channels .

The diagram to the right shows an incorrect attempt to set the system

to channel code 2 (shown as an example to avoid possible confusion).

The correct settings are shown to the left.

OFF

1 2 3 4 5 6 7 8

INCORRECT

OFF

1 2 3 4 5 6 7 8

CORRECT

Other Silent Alert Pager manuals

Silent Alert

Silent Alert SA3000 User manual

Popular Pager manuals by other brands

Alpha

Alpha Elite user guide

LRS

LRS RX-E467 user manual

Bellman & Symfon

Bellman & Symfon Visit BE1470 user manual

unication

unication E3 user manual

Infostream

Infostream X5 User's reference manual

Motorola

Motorola BR850 user guide

ACE TELECOM

ACE TELECOM ACE-2040 user manual

Intek

Intek Allure owner's manual

Pocsag

Pocsag PG-2092P user manual

Motorola

Motorola Bravo classic user guide

Motorola

Motorola LS750 user guide

Alert Systems

Alert Systems HyperGuard MP10D manual

Motorola

Motorola Talkabout T900 user guide

Motorola

Motorola Advisor Graphix CP1250 user guide

Radio Shack

Radio Shack 17-7040 owner's manual

PageOne

PageOne Advisor Graphix instruction manual

Syscall

Syscall Nttworks GP-210RT user manual

unication

unication G4 Configuring