Siemens SINAMICS S120 Quick start guide

___________________

SINAMICS

S120

CANopen interface

Commissioning Manual

Valid for:

Firmware version 5.1

11/2017

6SL3097

-4AA00-0BP3

Preface

Fundamental safety

instructions

Add infeed

CAN CBC10 Communication

Board

Configuration

Calculation/conversion

setpoints/actual values

Diagnosis

Operating modes

Appendix

Siemens AG

Division Digital Factory

Postfach 48 48

90026 NÜRNBERG

GERMANY

Document order number: 6SL3097-4AA00-0BP3

Ⓟ

10/2017 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

CANopen interface

Commissioning Manual, 11/2017, 6SL3097-4AA00-0BP3 5

Preface

SINAMICS documentation

The SINAMICS documentation is organized in the following categories:

●General documentation/catalogs

●User documentation

●Manufacturer/service documentation

Additional information

You can find information on the following topics at the following address

(https://support.industry.siemens.com/cs/de/en/view/108993276):

●Ordering documentation/overview of documentation

●Additional links to download documents

●Using documentation online (find and search in manuals/information)

Please send any questions about the technical documentation (e.g. suggestions for

improvement, corrections) to the following e-mail address

(mailto:docu.motioncontrol@siemens.com).

Siemens MySupport/Documentation

At the following address (https://support.industry.siemens.com/My/ww/en/documentation),

you can find information on how to create your own individual documentation based on

Siemens' content, and adapt it for your own machine documentation.

Training

At the following address (http://www.siemens.com/sitrain), you can find information about

SITRAIN (Siemens training on products, systems and solutions for automation and drives).

FAQs

You can find Frequently Asked Questions in the Service&Support pages under Product

Support (https://support.industry.siemens.com/cs/de/en/ps/faq).

SINAMICS

You can find information about SINAMICS at the following address

(http://www.siemens.com/sinamics).

Preface

CANopen interface

6Commissioning Manual, 11/2017, 6SL3097-4AA00-0BP3

Usage phases and their documents/tools (as an example)

Table 1 Usage phases and the available documents/tools

Usage phase

Document/tool

Orientation

SINAMICS S Sales Documentation

Planning/configuration •SIZER Engineering Tool

•Configuration Manuals, Motors

Deciding/ordering SINAMICS S120 catalogs

•SINAMICS S120 and SIMOTICS (Catalog D 21.4)

•SINAMICS Converters for Single-Axis Drives and SIMOTICS Motors (Catalog D 31)

•SINUMERIK 840 Equipment for Machine Tools (Catalog NC 62)

Installation/assembly •SINAMICS S120 Manual for Control Units and Additional System Components

•SINAMICS S120 Manual for Booksize Power Units

•SINAMICS S120 Manual for Booksize Power Units C/D Type

•SINAMICS S120 Manual for Chassis Power Units, Air-cooled

•SINAMICS S120 Manual for Chassis Power Units, Liquid-cooled

•SINAMICS S120 Manual for AC Drives

•SINAMICS S120 Manual Combi

•SINAMICS S120M Manual Distributed Drive Technology

•SINAMICS HLA System Manual Hydraulic Drive

Commissioning •STARTER Commissioning Tool

•Startdrive commissioning tool

•SINAMICS S120 Getting Started with STARTER

•SINAMICS S120 Getting Started with Startdrive

•SINAMICS S120 Commissioning Manual with STARTER

•SINAMICS S120 Commissioning Manual with Startdrive

•SINAMICS S120 CANopen Commissioning Manual

•SINAMICS S120 Function Manual Drive Functions

•SINAMICS S120 Safety Integrated Function Manual

•SINAMICS S120/S150 List Manual

•SINAMICS HLA System Manual Hydraulic Drive

Usage/operation •SINAMICS S120 Commissioning Manual with STARTER

•SINAMICS S120 Commissioning Manual with Startdrive

•SINAMICS S120/S150 List Manual

•SINAMICS HLA System Manual Hydraulic Drive

Maintenance/servicing •SINAMICS S120 Commissioning Manual with STARTER

•SINAMICS S120 Commissioning Manual with Startdrive

•SINAMICS S120/S150 List Manual

References •SINAMICS S120/S150 List Manual

Preface

CANopen interface

Commissioning Manual, 11/2017, 6SL3097-4AA00-0BP3 7

Target group

This documentation is intended for machine manufacturers, commissioning engineers, and

service personnel who use the SINAMICS drive system.

Benefits

This manual provides all of the information, procedures and operator actions required for the

particular usage phase.

Standard scope

The scope of the functionality described in this document can differ from that of the drive

system that is actually supplied.

●Other functions not described in this documentation might be able to be executed in the

drive system. However, no claim can be made regarding the availability of these functions

when the equipment is first supplied or in the event of service.

●The documentation can also contain descriptions of functions that are not available in a

particular product version of the drive system. The functionality of the supplied drive

system should only be taken from the ordering documentation.

●Extensions or changes made by the machine manufacturer must be documented by the

machine manufacturer.

For reasons of clarity, this documentation does not contain all of the detailed information on

all of the product types, and cannot take into consideration every conceivable type of

installation, operation and service/maintenance.

Technical Support

Country-specific telephone numbers for technical support are provided in the Internet at the

following address (https://support.industry.siemens.com/sc/ww/en/sc/2090) in the "Contact"

area.

Relevant directives and standards

You can obtain an up-to-date list of currently certified components on request from your local

Siemens office. If you have any questions relating to certifications that have not yet been

completed, please ask your Siemens contact person.

Certificates for download

The certificates can be downloaded from the Internet:

Certificates (https://support.industry.siemens.com/cs/ww/de/ps/13206/cert)

EC Declaration of Conformity

You can find the EC Declaration of Conformity for the relevant directives as well as the

relevant certificates, prototype test certificates, manufacturers declarations and test

certificates for functions relating to functional safety ("Safety Integrated") on the Internet at

the following address (https://support.industry.siemens.com/cs/ww/en/ps/13231/cert).

Preface

CANopen interface

8Commissioning Manual, 11/2017, 6SL3097-4AA00-0BP3

The following directives and standards are relevant for SINAMICS S devices:

●

European Low Voltage Directive

SINAMICS S devices fulfil the requirements stipulated in the Low-Voltage Directive

2014/35/EU, insofar as they are covered by the application area of this directive.

●

European Machinery Directive

SINAMICS S devices fulfil the requirements stipulated in the Low-Voltage Directive

2006/42/EU, insofar as they are covered by the application area of this directive.

However, the use of the SINAMICS S devices in a typical machine application has been

fully assessed for compliance with the main regulations in this directive concerning health

and safety.

●

Directive 2011/65/EU

SINAMICS S devices comply with the requirements of Directive 2011/65/EU on the

restriction of the use of certain hazardous substances in electrical and electronic devices

(RoHS II).

●

European EMC Directive

SINAMICS S devices comply with the EMC Directive 2014/30/EU.

●

EMC requirements for South Korea

SINAMICS S devices with the KC marking on the type plate satisfy the EMC

requirements for South Korea.

●

Eurasian conformity

SINAMICS S comply with the requirements of the Russia/Belarus/Kazakhstan customs

union (EAC).

●

North American market

SINAMICS S devices provided with one of the test symbols displayed fulfill the

requirements stipulated for the North American market as a component of drive

applications.

You can find the relevant certificates on the Internet pages of the certifier

(http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.html).

●

Specification for semiconductor process equipment voltage drop immunity

SINAMICS S devices meet the requirements of standard SEMI F47-0706.

●

Australia and New Zealand (RCM formerly C-Tick)

SINAMICS S devices showing the test symbols fulfill the EMC requirements for Australia

and New Zealand.

●

Quality systems

Siemens AG employs a quality management system that meets the requirements of ISO

9001 and ISO 14001.

Preface

CANopen interface

Commissioning Manual, 11/2017, 6SL3097-4AA00-0BP3 9

Not relevant standards

China Compulsory Certification

SINAMICS S devices do not fall in the area of validity of the China Compulsory Certification

(CCC).

EMC limit values in South Korea

The EMC limit values to be observed for Korea correspond to the limit values of the EMC

product standard for variable-speed electric drives EN 61800-3 of category C2 or the limit

value class A, Group 1 to KN11. By implementing appropriate additional measures, the limit

values according to category C2 or limit value class A, Group 1, are observed. Further,

additional measures may be required, such as using an additional radio interference

suppression filter (EMC filter).

The measures for EMC-compliant design of the system are described in detail in this manual

respectively in the EMC Installation Guideline Configuration Manual.

The final statement regarding compliance with the standard is given by the respective label

attached to the individual unit.

Ensuring reliable operation

The manual describes a desired state which, if maintained, ensures the required level of

operational reliability and compliance with EMC limit values.

Should there be any deviation from the requirements in the manual, appropriate actions (e.g.

measurements) must be taken to check/prove that the required level of operational reliability

and compliance with EMC limit values are ensured.

Spare parts

Spare parts are available on the Internet at the following address

(https://www.automation.siemens.com/sow?sap-language=EN).

Product maintenance

The components are subject to continuous further development within the scope of product

maintenance (improvements to robustness, discontinuations of components, etc).

These further developments are "spare parts-compatible" and do not change the article

number.

In the scope of such spare parts-compatible further developments, connector/connection

positions are sometimes changed slightly. This does not cause any problems with proper

use of the components. Please take this fact into consideration in special installation

situations (e.g. allow sufficient clearance for the cable length).

Preface

CANopen interface

10 Commissioning Manual, 11/2017, 6SL3097-4AA00-0BP3

Use of third-party products

This document contains recommendations relating to third-party products. Siemens accepts

the fundamental suitability of these third-party products.

You can use equivalent products from other manufacturers.

Siemens does not accept any warranty for the properties of third-party products.

Ground symbols

Table 2 Symbols

Symbol

Meaning

Connection for protective conductor

Ground (e.g. M 24 V)

Connection for function potential bonding

Notation

The following notation and abbreviations are used in this documentation:

Notation for faults and alarms (examples):

•

F12345

Fault 1234

•

A67890

Alarm 67890

•

C23456

Safety message

Notation for parameters (examples):

•

p0918

Adjustable parameter 918

•

r1024

Display parameter 1024

•

p1070[1]

Adjustable parameter 1070, index 1

•

p2098[1].3

Adjustable parameter 2098, index 1 bit 3

•

p0099[0...3]

Adjustable parameter 99, indices 0 to 3

•

r0945[2](3)

Display parameter 945, index 2 of drive object 3

•

p0795.4

Adjustable parameter 795, bit 4

Other manuals for SINAMICS S120

Table of contents

Other Siemens Recording Equipment manuals

Siemens

Siemens NCC-1F User manual

Siemens

Siemens SIMATIC RTLS4040T User manual

Siemens

Siemens PMI User manual

Siemens

Siemens SIPROTEC 7XV5662-0AC03 User manual

Siemens

Siemens WW8000 MP4.70 User manual

Siemens

Siemens IM 152 User manual

Siemens

Siemens N148/22 Service manual

Siemens

Siemens SIMOTION ADI4 User manual

Siemens

Siemens GAMMA instabus 5WG1 220-2AB21 Service manual

Siemens

Siemens RNI User manual

Siemens

Siemens SINAMICS V90 User manual

Siemens

Siemens SIMATIC NET DP/AS-i Link 20E User manual

Siemens

Siemens AEK84 User manual

Siemens

Siemens RNI User manual

Siemens

Siemens SEZ50MB Operator's manual

Siemens

Siemens SIMATIC NET CP 5613 User manual

Siemens

Siemens SIMATIC HMI KTP700F Mobile User manual

Siemens

Siemens MTP700 Unified Comfort User manual

Siemens

Siemens SIMATIC Distributed I/O System DP/ASi Link User manual

Siemens

Siemens VIU-20 User manual

Siemens

Siemens simatic ET 200MP User manual

Siemens

Siemens TC35 User guide

Siemens

Siemens NIC-C User manual

Siemens

Siemens SITOP PSU6200 Instructions for use

Popular Recording Equipment manuals by other brands

KV2 Audio

KV2 Audio 500 Series user guide

Robotics Technologies

Robotics Technologies microBus-Cam II installation manual

Seca

Seca 460 quick start guide

Cognex

Cognex MVS-8000 Series Hardware manual

Mect

Mect MPNC006 Series user manual

Bad Caf

Bad Caf THE LEASH operating manual

Strymon

Strymon NIGHTSKY user manual

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U user manual

Tews Technologies

Tews Technologies TPMC465 user manual

Honeywell

Honeywell Excel 50 user guide

SeaLevel

SeaLevel COMM+8.LPCI user manual

Arturia

Arturia AUDIOFUSE STUDIO user manual

Rukra

Rukra RK-1240 quick start guide

Samson

Samson SCOM owner's manual

Dynacord

Dynacord DPS260 owner's manual

Nice

Nice Core user manual

Pyle Pro

Pyle Pro PSS8 manual

RF-System

RF-System TinyGate Assembly and user's manual