Siemens P1 400A User manual

P1 400APanelboard Kits

MBKJD1 & MBKJD3

For Main JD Breaker

Installation

Instructions

12-A-1070-01 Rev. 2

Installation Instructions

The following instructions are for the installation of a Siemens JD main breaker kit in a 400 amp Type P1 panelboard.

The parts provided in this kit connect Type JD main breakers to 1 phase, 2 or 3 wire systems or to 3 phase, 3 or 4 wire

systems. For all 1 phase systems, disregard the B-phase connector instructions. For 1 phase 2 wire and 3 phase 3 wire

systems, disregard the neutral instructions. The breaker is not included in the kit and must be purchased separately. Be

sure to select the appropriate breaker for the voltage, system, and feed location in use.

Bottom-feedmainsarereversefed,andrequireTypeJXDbreakers.Top-feedmainsmaybeeitherTypeJDorJXD:

To install the main breaker:

1. Lock off all power to this equipment before working on it.

2. Removethedeadfrontandmainlugs,ifinstalled.Refer

to Figure 2 on page 4 to determine the correct breaker

mountingforthe panel'sfeedlocation. Insertthetwo

1/4"-20x 2-3/4" selfthreading screws (item 9)through

theappropriateendofthebreakercaseandthroughthe

outer holes on the support barrier (item 8) as shown in

Figure1, to retainthe barrier during installation.Fasten

the breaker to the support.

3. Position one of the outer breaker connectors (items 1 &

2) so that the single-hole end rests on the breaker pad

andthe double-hole end rests on the panel section or

main bus. Note that the outer conncetors are mirror

imagesand arenot interchangeable.Attach the

conncetorto the breaker padusing a 3/8"-16machine

screw. (item 10), a helical spring lock washer (item 11),

and a plain washer (item 12) as shown. Do not tighten at

this time. Repeat the process to attach the other outer

connectortothebreaker.

4. 3 phase panels require a B-phase connection. Stack the

upperB-phaseconnector(item3)abovethelower

connector (item 4). Attach the single-hole ends to the

centerpolebreakerpadusingidenticalhardware(items

10, 11, & 12) as for the outer connectors. Do not tighten

at this time.

5. Fasten all breaker connectors to the panel section or

mainbus usingtwo 5/16"-18 threadforming SEMS

screws (item 13) per joint. Torque the screws to the

valueindicatedonthetighteningtorque labelonthe

rearofthedeadfront.

6. Torqueall3/8"-16machinescrews atthebreaker

connections to 228 in-lb.

7. On 1 phase 3 wire systems and 3 phase 4 wire

systems,neutral lugs are required. Loosenthe wire

binding screw in the lay-in lug (item 5), remove the cap

plate, and place the lug on the lug pad inside the neutral

barrier cavity, as shown. Align the two lug holes with the

mounting holes on the lug pad centerline. Fasten the lug

withtwo 1/4"-20 thread formingscrews (item 14). Place

the tang lug (item 6) in the other barrier cavity, and align

its hole with the innermost lug pad hole. See Figure 2 on

page 4 for the correct position. Fasten the lug using a

1/4" -20 self threading screw (item 14) with a plain

washer(item 15). Torque alllug mounting screws to the

valuesindicatedonthe tighteningtorquelabel onthe

rearofthedeadfront.

8. Removethe mainlugfillerplatefromthedeadfrontmain

openingif present. Refer againto Figure 2on page 4, to

determinethecorrectorientationofthedeadfrontmain

fillerplate (item 7)for the panel's feedlocation. Fasten

the filler plate to the back of the dead front using four #8-

32 screws (item 16) screwed in from the front. Apply the

"MAIN"label (item17)as shown.

9. Beforeenergizingthepanel,ensurethat allconnections

havebeentorquedandthedeadfrontisinstalled.

PAGE3

MBKJD1&MBKJD3

Hazardous voltage.

Will cause death or serious

injury.

Keep out.

Qualified personnel only.

Disconnect and lock off all power before

working on this equipment.

TopFeedMainBreakers

BottomFeed MainBreakers JD,HJD,JXD,HJXD

JXD,HJXD

The400AP1panelprovideswiringspaceforthefollowingcableoptions:

(2)250 MCM line cables perphase

(1)600 MCM linecable per phase UsebreakerlinelugTA2J6500orcopperlugTC2J6500

UsebreakerlinelugTA1L6750orcopperlugTC1J6600

PAGE4

MBKJD1&MBKJD3

This manual suits for next models

Table of contents

Other Siemens Industrial Electrical manuals

Siemens

Siemens 3TS33 User manual

Siemens

Siemens 5WG1 262-1EB01 Service manual

Siemens

Siemens SIMATIC RTLS PCB OEM PULSE User manual

Siemens

Siemens SINAMICS G130 User manual

Siemens

Siemens 3VL9300-3TN00 User manual

Siemens

Siemens SIMOVERT MASTERDRIVE SLE User manual

Siemens

Siemens SIVACON 8PS BD01 User manual

Siemens

Siemens 7XR61 Series Manual

Siemens

Siemens SIVACON 8PS User manual

Siemens

Siemens 3VA9157-0PK11 User manual

Siemens

Siemens SINAMICS S120 User manual

Siemens

Siemens SINUMERIK 840D sl User manual

Siemens

Siemens 3VA9602-0WA05 User manual

Siemens

Siemens SB04TLI Owner's manual

Siemens

Siemens SIRIUS Contactor S2 User manual

Siemens

Siemens 3RV1952-1E Series User manual

Siemens

Siemens SWT-3000 Technical Document

Siemens

Siemens RCD310 Series User manual

Siemens

Siemens MICROMASTER 430 Operating and maintenance instructions

Siemens

Siemens 3RT1955-5A/N Series User manual

Siemens

Siemens 3VA9277-0FK2 Series User manual

Siemens

Siemens SIRIUS 3RA131 8XB Series User manual

Siemens

Siemens 3WX3666-8JA0 Series User manual

Siemens

Siemens 3VL9431 - 6U.30 User manual

Popular Industrial Electrical manuals by other brands

Rexroth Indramat

Rexroth Indramat DURADRIVE SYSTEM200 Project planning manual

Abtech

Abtech HVJB Series Installation, operation & maintenance instructions

Murata

Murata GRM0335C1H8R1DA01 Series Reference sheet

SAF-HOLLAND

SAF-HOLLAND CBX 5415.5 Installation and operation manual

Eaton

Eaton Ulusoy HMH24-04 user manual

Newlong

Newlong NP-7H NSTRUCTION MANUAL/PARTS LIST

Murata

Murata GJM0335C1E4R4BB01 Series Reference sheet

Stahl

Stahl 8575/12 operating instructions

SI Pegasus installation instructions

Murata

Murata GRM1555C1H2R7CA01 Seies Reference sheet

Murata

Murata GRM0225C1E6R4BA03 Series Reference sheet

Cooper Power Systems

Cooper Power Systems VXE15 Installation and operation instructions

S&C

S&C Vista SD manual

Murata

Murata GRM0335C2A7R3CA01 Series Reference sheet

Murata

Murata GRM32ER60G227ME05 Series Reference sheet

Rockwell Automation

Rockwell Automation Allen-Bradley MP-Series installation instructions

Phasemation

Phasemation DG-100 owner's manual

Murata

Murata GRM219R61C225KA88 Series Reference sheet