Siemens 7XV5673 User manual
Siemens Aktiengesellschaft Order No.: E50417-B1050-C484-A3
Document Release: E50417-B1050-C484-A3.00
Edition: 05.2012
Product version: V2.00
Statement of Conformity
Further IEEE Std C 37.90
Note
Please observe the Notes and Warnings for your own safety in
this Product Information. This Product Information contains
important information about the SICAM I/O Unit 7XV5673 and
is part of the product delivery.
This product complies with the directive of the Council of the
European Communities on the approximation of the laws of
the Member States relating to electromagnetic compatibility
(EMC Council Directive 2004/108/EC) and concerning elec-
trical equipment for use within specified voltage limits (Low-
voltage Directive 2006/95/EC).
This conformity has been established by means of tests con-
ducted by Siemens AG in accordance of the Council Direc-
tive in agreement with the generic standards EN 61000-6-2
and EN 61000-6-4 for the EMC directives, and with the stan-
dard EN 60255-27 for the low-voltage directive.
The device has been designed and produced for industrial
use.
This product is UL-certified to Standard UL 508, based on the specifica-
tion stated in Chapter 15 (Technical Data).
UL File No.: E194016
IND. CONT. EQ.
69CA
3SICAM I/O Unit 7XV5673, Product Information
E50417-B1050-C484-A3, Edition: 03.2012
Contents
1 Preface 4
2 General Information 5
3 Information for Your Safety 6
4 Used Symbols 9
5 Ordering Information 10
6 Application 11
7 Design 13
8 Assembly and Commissioning 15
9 Application Examples 21
10 Interfaces 25
11 Replacing the Battery 29
12 LED Indications 31
13 Troubleshooting and Repair 35
14 Storage and Transport 36
15 Technical Data (Selection) 37
4 SICAM I/O Unit 7XV5673, Product Information
E50417-B1050-C484-A3, Edition: 03.2012
1Preface
Disclaimer of liability
This document has been subjected to rigorous techni-
cal review before being published. It is revised at regu-
lar intervals, and any modifications and amendments
are included in the subsequent issues. The content of
this document has been compiled for information pur-
poses only. Although Siemens AG has made best
efforts to keep the document as precise and up-to-date
as possible, Siemens AG shall not assume any liability
for defects and damage which result through use of the
information contained herein.
This content does not form part of a contract or of busi-
ness relations; nor does it change these. All obligations
of Siemens AG are stated in the relevant contractual
agreements.
Siemens AG reserves the right to revise this document
from time to time.
Copyright
Copyright © Siemens AG 2012. All rights reserved.
The disclosure, duplication, distribution and editing of
this document, or utilization and communication of the
content are not permitted, unless authorized in writing.
All rights, including rights created by patent grant or
registration of a utility model or a design, are reserved.
5SICAM I/O Unit 7XV5673, Product Information
E50417-B1050-C484-A3, Edition: 03.2012
Registered Trademarks
SIPROTEC®, SENTRON®, and SICAM® are regis-
tered trademarks of Siemens AG. An unauthorized use
is illegal.
All other designations in this document can be trade-
marks whose use by third parties for their own pur-
poses can infringe the rights of the owner.
2 General Information
These Product Information contain the information
required for the proper use of the devices described
here. They are intended for personnel suitably qualified
in electrical engineering with special training or relevant
expertise in the area of automation engineering.
To ensure the safe installation, commissioning,
operation and maintenance of the devices described in
this document, personnel must be familiar with and
practice the safety instructions and warnings in this
document correctly. Only electrically qualified
personnel (see “Personnel qualified in electrical
engineering”) have the special knowledge required to
interpret the general safety notes and warnings in this
document correctly and apply them to suit the job at
hand.
These Product Information are an integral part of the
product. However, they cannot cover all details of all
versions of the devices described here, nor can they
NOTE
For further information, see the Device Manual
SICAM I/O Unit 7XV5673, order number E50417-
H1040-C484.
6 SICAM I/O Unit 7XV5673, Product Information
E50417-B1050-C484-A3, Edition: 03.2012
provide for all possible conditions concerning
installation, operation, or maintenance.
If you need any further information, or if you are facing
special problems that this document does not deal with
in sufficient detail, please feel free to order the manual
mentioned in Chapter 1.
If you have any questions about the device, please con-
tact our Siemens sales partner responsible in your
region.
Our Energy Customer Support Center is available to
you twenty-four hours a day.
Phone: +49 (1805) 24-7000
Fax: +49 (1805) 24-2471
Internet: www.siprotec.com
e-mail: [email protected]
3 Information for Your Safety
These Product Information do not list all the safety
measures required to operate the equipment (module,
device), since specific operating conditions may make
additional measures necessary. However, they contain
important information that you must observe in order to
ensure your personal safety and to avoid material dam-
7SICAM I/O Unit 7XV5673, Product Information
E50417-B1050-C484-A3, Edition: 03.2012
age. Such information is highlighted by a warning trian-
gle and indicated as follows depending on the degree
of danger:
DANGER
Danger means that death or severe injury will occur if
the appropriate safety measures are not taken.
Follow all advice instructions to prevent death or
severe injury.
WARNING
Warning means that death or severe injury can occur
if the appropriate safety measures are not taken.
Follow all advice instructions to prevent death or
severe injury.
CAUTION
Caution means that minor or moderate injury can
occur if the appropriate safety measures are not taken.
Follow all advice instructions to prevent minor injury.
NOTICE
Notice means that damage to property can occur if the
appropriate safety measures are not taken.
Follow all advice instructions to prevent damage to
property.
NOTE
is important information about the product, the handling
of the product, or the part of the documentation in ques-
tion to which special attention must be paid.
8 SICAM I/O Unit 7XV5673, Product Information
E50417-B1050-C484-A3, Edition: 03.2012
Personnel qualified in electrical engineering
Commissioning and operation of the equipment (mod-
ule, device) described in this Product Information must
be performed by personnel qualified in electrical engi-
neering only. As used in the safety notes contained in
this Product Information, electrically qualified personnel
are those persons who are authorized to commission,
release, ground and tag devices, systems, and electri-
cal circuits in accordance with safety standards.
Use as prescribed
The equipment (device, module) must not be used for
any other purposes than those described in the catalog
and the Technical Description. If it is used together with
third-party devices and components, these must be
recommended or approved by Siemens.
If the device is not used in accordance with this product
information, the scheduled protection is impaired.
Correct and safe operation of the product requires ade-
quate transportation, storage, installation, and assem-
bly as well as appropriate use and maintenance.
During the operation of electric equipment, it is
unavoidable that certain parts of this equipment will
carry hazardous voltages. Severe injury or material
damage can occur if the appropriate measures are not
taken:
Before making any connections at all, ground the
equipment at the grounding terminal.
Hazardous voltages can be present on all switching
components connected to the power supply.
Even after the supply voltage has been discon-
nected, hazardous voltages can still be present in the
equipment (capacitor storage).
9SICAM I/O Unit 7XV5673, Product Information
E50417-B1050-C484-A3, Edition: 03.2012
The limiting values indicated in the product informa-
tion must not be exceeded; this also refers to testing
and commissioning.
4 Used Symbols
Table 4-1 Used Symbols
No. Symbol Description
1Direct current
IEC 60417-5031
2Alternating current
IEC 60417-5032
3Direct current and alternating
current
IEC 60417-5033
4Protective conductor terminal
IEC 60417-5019
5Caution, risk of electric shoc
6Caution, risk of danger
ISO 7000-0434
10 SICAM I/O Unit 7XV5673, Product Information
E50417-B1050-C484-A3, Edition: 03.2012
5 Ordering Information
Ordering code for a device:
Optional accessories are listed in the Device Manual
SICAM I/O Unit 7XV5673, order number E50417-
H1040-C484.
Description
SICAM I/O Unit
Order No. /MLFB
SICAM I/O Unit, integrated electrical
Ethernet interface, connection RJ45
Device type
Case 96 mm x 96 mm x 100 mm
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1AA0JJ 0-
673-
57XV
Inputs and outputs
3 Binary inputs with adjustable threshold voltage,
3 Relay outputs (2 NO, 1 CO)
3 Binary inputs with adjustable threshold voltage,
3 Relay outputs (2 NO, 1 CO)
Serial interface and communication protocol
Without serial communication
RS485 – Modbus RTU, I/O mirror
FO 820 nm – Modbus RTU, I/O mirror
0
1
Protection class
Snap-on mounting unit, protection class IP20
Communication interface and communication protocol
Ethernet interface with Modbus TCP /UDP or
I/O mirror
Ethernet interface with Modbus TCP /UDP,
I/O mirror, or IEC 61850 (GOOSE, MMS, Reporting)
Features
Integrated Ethernet switch
2
1
2
Other manuals for 7XV5673
1
This manual suits for next models
1
Table of contents
Other Siemens I/O System manuals
Siemens
Siemens SIMATIC ET 200SP User manual
Siemens
Siemens SIMATIC ET 200S User manual
Siemens
Siemens FDCIO223 User manual
Siemens
Siemens SIMATIC TI505 User manual
Siemens
Siemens SIMATIC PROFINET Parts list manual
Siemens
Siemens Simatic CFU Quick start guide
Siemens
Siemens SIMATIC ET 200S User manual
Siemens
Siemens SIMATIC ET 200SP HA User manual
Siemens
Siemens SIMATIC ET 200eco User manual
Siemens
Siemens SIMATIC ET 200SP User manual
Siemens
Siemens APACS+ Manual
Siemens
Siemens DI 16x24VDC HF User manual
Siemens
Siemens SIMATIC ET 200eco PN Technical Document
Siemens
Siemens SIMATIC ET 200SP HA User manual
Siemens
Siemens SICAM A8000 Series User manual
Siemens
Siemens SIMATIC ET 200AL User guide
Siemens
Siemens SIMATIC ET 200SP User manual
Siemens
Siemens SIMATIC ET 200SP HA User manual
Siemens
Siemens PPM-1U32.BPR User manual
Siemens
Siemens SIMATIC ET 200iSP User manual
