Siemens VN2001-A1 User manual

A6V10370415_en--_a 1

INSTALLATION INSTRUCTIONS

Model VN2001-A1 Ethernet Module (10/100 BaseTx)

The optional Model VN2001-A1 Ethernet Module (10/100 BaseTx) is an interface card which provides dual

interconnecting copper wire links for networked systems.

FEATURES

The principal features of the VN2001-A1 (10/100 BaseTx) include:

Is easily plugged into the host card or assembly

Is automatically identified by the system at power up

Protects the Ethernet signal path from overvoltage caused by electrostatic

discharge (ESD) or electrical fast transients (EFT)

Provides optimal ground fault detection (user selectable)

Provides Power-over-Ethernet (PoE), 24V, 500mA (user

selectable)

Can be used in the UL and ULC markets

PRE-INSTALLATION

1. Determine from the site-specific shop drawings whether the VN2001-A1 should be set for ground fault

supervision alone, Power-over-Ethernet (PoE) plus ground fault supervision, or neither function.

2. For ground fault supervision alone, set the jumpers as illustrated in Figure 2a. For Power-over

Ethernet plus ground fault supervision, set the jumpers as illustrated in Figure 2b. If neither ground

fault supervision nor PoE is required, set the jumpers to the default setting as illustrated in Figure 2c

a. Ground Fault Only b. Power-over-Ethernet and c. Open (default setting)

Ground Fault

Figure 2

Jumper Settings

18V-30V

GND

Figure 1

VN2001-A1 Ethernet Module

(10/100 BaseTx

18V-30V

GND

18V-30V

GND

A6V10370415_en--_a 2

OPERATION

The VN2001-A1 Ethernet Module (10/100 BaseTx) can be used both in Voice networks of FV2025/2050

Fire Voice Control Panels and in generic Ethernet systems.

Operation in a Voice Network of FV2025/2050 Fire Voice Control Panels

The VN2001-A1 Ethernet Module (10/100 BaseTx) is an optional card that plugs into the VCC Card Cage to

provide an electrical interface for an Ethernet backbone network of FV2025/2050 Fire Voice Control Panels

(see Figure 3). Each link in a Backbone is independently of any other link. It can be implemented as either

copper wire or fiber-optic cable without any regard to what is used for the other links in the network.

NOTE: For installation instructions applicable to fiber-based links, see Siemens Industry, Inc., Building

Technologies Division, document number A6V10370419 Installation Instructions for the Model

VN2002-A1 Ethernet Module (MM) and the Model VN2003-A1 Ethernet Module (SM).

The backbone is a dual self-healing, redundant, ring network that is able to detect failures and then

automatically isolate and recover from them using an alternate routing.

VOICE CARD

CAGE

VOICE CARD

CAGE

VOICE CARD

CAGE

COPPER / FIBER ETHERNET BACKBONE

NETWORK

FV2025/2050

PANEL FV2025/2050

PANEL

VN2001-A1 (10/100 BASE Tx)

VN2002-A1 (MM)

VN2003-A1 (SM) ETHERNET

MODULES

Figure 3

Ethernet Network Topology in a Voice Network of FV2025/2050 Panels

Operation in a Generic Ethernet Network

In addition to its use in an Ethernet backbone network of FV2025/2050 Fire Voice Control Panels (as

illustrated in Figure 3), the VN2001-A1 Ethernet Module (10/100 BaseTx) can also be used to support copper

wire connections among standalone FN2012-A1 Ethernet Switches (modular).

Controls and Indicators

The two LEDs on the VN2001-A1 which are located at the copper cable connector indicate the following:

Green = Link established

Yellow = Signal activity

A6V10370415_en--_a 3

MOUNTING

Mounting the VN2001-A1 Ethernet Module, 10/100 BaseTx, in a Voice Network of FV2025/2050 Fire

Voice Control Panels

CAUTION: Power down the Voice Panel before mounting the VN2001-A1.

1. Open the middle door of the FV2025/2050 Fire Voice Control Panel.

2. Unscrew the latch on the front of the Card Cage and remove the Card Cage cover.

3. If a VCC2001-A1 Voice CPU is installed in card slot X202, remove it. If no VCC2001-A1 is

installed, proceed to the next step.

4. Referring to Figure 4, if the two knockouts for Ethernet modules are still present in the Card

Cage top panel, remove them. To avoid damage to sensitive electronic components, remove

any burrs that may be present in the knockout opening.

5. Install the VCC2001-A1 Voice CPU card into card slot X202 according to instructions provided in

Siemens Industry, Inc., Building Technologies Division, document number A6V10397772

Installation Instructions for the Model VCC2001-A1 Voice CPU Card..

Figure 4

Removing knockouts for Ethernet Modules

6. Refer to the site specific shop drawings to determine which position on the Voice CPU Card the

module is to be installed in.

7. Insert the VN2001-A1 through the specified knockout opening on top of the VCA2002-A1 Card

Cage and carefully press it into the multi-pin connector mounted on the VCC2001-A1 Voice

CPU card. The multi-pin connector is located approximately 21/2”below the knockout opening,

as illustrated in Figure 5. Install the second module for the other link in the same manner

through the remaining knockout opening.

8. Tighten the fastening pin on the top of each module (see Figure 5) by turning it clockwise until

KNOCKOUTS FOR

ETHERNET MODULES

COVER LATCH

CARD CAGE COVER

COVER GUIDE

CARD CAGE TOP PANEL

COVER GUIDE

A6V10370415_en--_a 4

the modules are firmly held in place by the Card Cage.

NOTE: If it becomes necessary to deinstall the VCC2001-A1 Voice CPU Module, first remove the

Ethernet modules that have been mounted on it.

Figure 5

Ethernet Modules Installed in the VCA2002-A1 Card Cage

9. Replace the Card Cage cover by re-inserting it into the top of the Card Cage and sliding it

downward until it reaches bottom.

10. Screw the cover latch back into the Card Cage cover.

Mounting the VN2001-A1 Ethernet Module, 10/100 BaseTx, in an FN2012-A1 Ethernet Switch (Modular)

1. Remove the screws fastening the cover to the body of the FN2012-A1 Ethernet Switch

(modular) and lift the cover off the assembly.

2. Please refer to Figure 6. If necessary, remove one of the knockouts in the FN2012-A1 Ethernet

Switches (modular) side panel.

VN2002/VN2003-A1

ETHERNET MODULE (MM or SM)

VN2001-A1 ETHERNET

MODULE (10/100 BaseTx)

MULTI-PIN CONNECTOR

FASTENING PIN

A6V10370415_en--_a 5

Figure 6

Mounting the VN2001-A1 Ethernet Module in the FN2012-A1 Ethernet Switch

3. Insert the VN2001-A1 Ethernet Module (10/100 BaseTx) through the knockout opening and

carefully press it into the multi-pin connector mounted on the circuit card inside the switch body.

The multi-pin connector is located approximately 21/2inches inside the opening.

4. Screw the fastening pin on the VN2001-A1 module into the mating hole in the side of the

FN2012-A1 Ethernet Switch (modular).

5. Replace the cover on the FN2012-A1 Ethernet Switch (modular).

WIRING

There are no wiring operations for installing the VN2001-A1 onto the VCC2001-A1 Voice CPU card or

into an FN2012-A1 Ethernet Switch (modular).

When using the VN2001-A1 Ethernet Module (10/100 BaseTx) to connect FV2025/2050 Panels, consult

the site-specific shop drawings for instructions on cabling FV2025/2050 Panels together to establish

Ethernet rings. A single multi-conductor cable is used to connect from one module to the next in the ring.

Ethernet cable specifications are provided in Siemens Industry, Inc., Building Technologies Division,

document number A6V10380472 Installation Instructions for the Model VCA2002-A1 Card Cage, Table

2 Cable Specifications.

FN2012-A1 ETHERNET

SWITCH (MODULAR)

KNOCKOUT FOR

ETHERNET MODULES

MULTI-PIN

CONNECTORS

FASTENING PIN

HOLE FOR FASTENING PIN

VN2001-A1 ETHERNET

MODULE (10/100 BASE Tx)

A6V10370415_en--_a 6

ELECTRICAL RATINGS

VN2001-A1 Ethernet Module (10/100 BaseTx) Power Requirements

Ethernet option, no PoE

Aux (20 –30VDC) 35mA max

MoNET: 36mA

With PoE active

Aux (20 –30VDC) 35mA, max

MoNET: 36mA, max

A6V10370415_en--_a 7

‘This page has been left intentionally blank’

A6V10370415_en--_a 8

‘This page has been left intentionally blank’

Siemens Industry, Inc. Siemens Canada Limited Document ID: A6V10370415_en--_a

Building Technologies Division Building Technologies Division P/N: A5Q00054390

Florham Park, NJ 2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

Table of contents

Other Siemens Control Unit manuals

Siemens

Siemens SIRIUS 3SF5811 A Series User manual

Siemens

Siemens SINORIX CPY-35 User manual

Siemens

Siemens PM-E F pm DC24V PROFIsafe User manual

Siemens

Siemens SINAMICS G120 User manual

Siemens

Siemens SINUMERIK 808D Quick start guide

Siemens

Siemens PS-35 User manual

Siemens

Siemens Siwarex U Application guide

Siemens

Siemens SIJECT 16i User manual

Siemens

Siemens SIMATIC ET 200SP User manual

Siemens

Siemens SIMATIC EMS400S PSB-S User manual

Siemens

Siemens SINAMICS V60 User manual

Siemens

Siemens SIMOCODE pro User manual

Siemens

Siemens LVM User manual

Siemens

Siemens SINAMICS G110M User manual

Siemens

Siemens LAL Series User manual

Siemens

Siemens SINUMERIK 840DE SL Quick start guide

Siemens

Siemens Simatic S7-1500 User manual

Siemens

Siemens V P45 Series User manual

Siemens

Siemens CZM-1B6 Service manual

Siemens

Siemens SIPROTEC User manual

Siemens

Siemens 3AD8 User manual

Siemens

Siemens SINUMERIK 808D User manual

Siemens

Siemens RWF50 User guide

Siemens

Siemens SINAMICS DCM User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual