Siemens SIPROTEC 7SJ80 User manual

E50417-K1150-C342-A6

SIPROTEC

7SJ80 / 7SK80

V4.6

Product Information

Siemens Aktiengesellschaft Order No.: E50417-K1150-C342-A6

Subject to change without prior notice.

Document Release V04.05.01

Edition 07.2010

Caution

Please observe Notes and Warnings for your own safety in Chapter 2.

Note

This Product Information contains important information about the

SIPROTEC 7SJ80 / 7SK80.

It is part of the product supplied, and the information in it should be

considered more up-to-date than any other information if uncertainties

arise.

3SIPROTEC 7SJ80 / 7SK80 V4.60, Product Information

E50417-K1150-C342-A6, Edition 07.2010

Table of Contents

1 General 4

2 Notes on Safety 5

3 Statement of Conformity 7

4 Unpacking and Re-packing 8

5 Storage and Transport 9

6 Dimensions 10

7 Installation Notes 13

8 Connection Notes 14

9 Limit Values of Inputs and Outputs 26

10 General Diagrams 29

11 Operating Pre-conditions 39

4SIPROTEC 7SJ80 / 7SK80 V4.60, Product Information

E50417-K1150-C342-A6, Edition 07.2010

1 General

Disclaimer of Liability

Although we have carefully checked the contents of this publication for

conformity with the hardware and software described, we cannot guaran-

tee complete conformity since errors cannot be excluded.

The information provided in this Product Information is checked at regular

intervals and any corrections that might become necessary are included

in the next releases. Any suggestions for improvement are welcome.

Subject to change without prior notice.

The reproduction, transmission or use of this document or its contents is

not permitted without express written authority. Offenders will be liable for

damages. All rights, including rights created by patent grant or registration

of a utility model or design, are reserved.

Registered Trademarks

SIMATIC®, SIMATIC NET®, SIPROTEC®, DIGSI®, SIMEAS®, SICAM®

and SINAUT®are registered trademarks of SIEMENS AG. All other pro-

duct and brand names in this manual might be trademarks, the use of

which by third persons for their purposes might infringe the rights of their

respective owners.

Note:

For further information see

SIPROTEC 7SJ80 V4.60, Manual E50417-G1140-C343,

SIPROTEC 7SK80 V4.60, Manual E50417-G1140-C344,

SIPROTEC System Description E50417-H1176-C151,

ReadMe-USB.pdf for DIGSI V4.82 (www.siprotec.com).

5SIPROTEC 7SJ80 / 7SK80 V4.60, Product Information

E50417-K1150-C342-A6, Edition 07.2010

2 Notes on Safety

This manual does not constitute a complete catalog of all safety measures

required for operating the equipment (module, device) in question

because special operating conditions might require additional measures.

However, it does contain notes that must be adhered to for your own per-

sonal safety and to avoid damage to property. These notes are highlighted

with a warning triangle and different keywords indicating different degrees

of danger:

Danger

means that death, severe injury, or substantial damage to property will

occur if the appropriate safety measures are not taken.

Warning

means that death, severe injury, or substantial damage to property can

occur if the appropriate safety measures are not taken.

Caution

means that minor injury or damage to property can occur if the appropriate

safety measures are not taken.

Caution

means that damage to property can occur if the appropriate safety measu-

res are not taken.

Note

is important information about the project, handling the product, or the part

of the documentation in question, to which special attention must be paid.

6SIPROTEC 7SJ80 / 7SK80 V4.60, Product Information

E50417-K1150-C342-A6, Edition 07.2010

Qualified Personnel

Commissioning and operation of the equipment (module, device) descri-

bed in this manual must be performed by qualified personnel only. As

used in the safety notes contained in this manual, qualified personnel are

those persons who are authorized to commission, release, ground, and

tag devices, systems, and electrical circuits in accordance with safety

standards.

Use as Prescribed

The equipment (device, module) must not be used for any other purposes

than those described in the Catalog and the Technical Description. If it is

used together with third-party devices and components, these must be

recommended or approved by Siemens.

Correct and safe operation of the product requires adequate transporta-

tion, storage, installation, and mounting as well as appropriate use and

maintenance.

During operation of electrical equipment, it is unavoidable that certain

parts of this equipment will carry dangerous voltages. Severe injury or

damage to property can occur if the appropriate measures are not taken:

•Before making any connections at all, ground the equipment at the PE

terminal.

•Hazardous voltages can be present on all switching components con-

nected to the power supply.

•Even after the supply voltage has been disconnected, hazardous vol-

tages can still be present in the equipment (capacitor storage).

•The secondary circles of the current transformer in the system must not

be operated while open.

•The limit values indicated in the manual or the operating instructions

must not be exceeded; that also applies to testing and commissioning.

7SIPROTEC 7SJ80 / 7SK80 V4.60, Product Information

E50417-K1150-C342-A6, Edition 07.2010

3 Statement of Conformity

Further

IEEE Std C37.90

This product is UL-certfied with the values as stated in the Technical Data.

file E194016

This product complies with the directive of the Council of the European

Communities on the approximation of the laws of the Member States

relating to electromagnetic compatibility (EMC Council Directive 2004/

108/EC) and concerning electrical equipment for use within specified

voltage limits (Low-voltage Directive 2006/95/EC).

This conformity has been established by means of tests conducted by

Siemens AG in accordance of the Council Directive in agreement with

the generic standards EN 61000-6-2 and EN 61000-6-4 for the EMC

directives, and with the standard EN 60255-27 for the low-voltage direc-

tive.

The device has been designed and produced for industrial use.

The product is conforming to the international standards of the series

IEC 60255 and the German regulation of VDE 0435.

NOTE concerning battery disposal

The batteries must only be replaced with the same type or a another type

recommended by the manufacturer. Improper replacement involves

explosion hazard. For disposing the batteries it is necessary to observe

the local national / international directives.

8SIPROTEC 7SJ80 / 7SK80 V4.60, Product Information

E50417-K1150-C342-A6, Edition 07.2010

UL-certification conditions

Servicing of the circuitry involving the batteries and replacement of the

lithium batteries shall be done by a trained technician.

Replace Battery with VARTA or Panasonic Cat. Nos. CR 1/2 AA or BR 1/

2 AA only. Use of another Battery may present a risk of fire or explosion.

See manual for safety instructions.

Caution: The battery used in this device may present a fire or chemical

burn hazard if mistreated. Do not recharge, disassemble, heat above

100 °C (212 °F) or incinerate.

Dispose of used battery promptly. Keep away from children.

4 Unpacking and Re-packing

When dispatched from the factory, the equipment is packed in accor-

dance with the guidelines laid down in IEC 60255–21 which specify the

impact resistance of packaging.

This packing shall be removed with care, without force and without the use

of inappropriate tools. The equipment should be visually checked to

ensure that there are no external traces of damage.

Please observe absolutely all notes and hints which may be enclosed in

the packaging.

Before initial energization with supply voltage, or after storage, the relay

shall be situated in the operating area for at least two hours in order to

ensure temperature equalization and to avoid humidity influences and

condensation.

9SIPROTEC 7SJ80 / 7SK80 V4.60, Product Information

E50417-K1150-C342-A6, Edition 07.2010

5 Storage and Transport

SIPROTEC® relays should be stored in dry and clean rooms. The limit

temperature range for storage of the relays or associated spare parts is

−25 °C to +55 °C, corresponding to −13 °F to 131 °F.

The relative humidity must be within limits such that neither condensation

nor ice forms.

It is recommended to reduce the storage temperature to the range

+10 °C to +35 °C (50 °F to 95 °F); this prevents early ageing of the

electrolytic capacitors which are contained in the power supply.

For very long storage periods, it is recommended to connect the relay to

the auxiliary voltage source for one or two days every other year, in order

to regenerate the electrolytic capacitors. The same is valid before the

relay is finally installed.

For further transport, the transport packing can be re-used when applied

in the same way. The storage packing of the individual relays is not suited

for transport. If alternative packing is used, this must also provide the

same degree of protection against mechanical shock and vibration as laid

down in IEC 60255–21–1 class 1 and IEC 60255–21–2 class 1.

The Lithium-batteries in our equipment are subject to Special Provision

188 of the UN Recommendations on the Transport of Dangerous Goods

Model Regulations and Special Provision A45 of the IATA Dangerous

Goods Regulation and the ICAO Technical Instructions. This is only valid

for the original battery or original spare batteries.

10 SIPROTEC 7SJ80 / 7SK80 V4.60, Product Information

E50417-K1150-C342-A6, Edition 07.2010

6 Dimensions

Figure 1 Dimensional drawing of a 7Sx80 for panel flush or cubicle

mounting (housing size 1/6)

Figure 2 Dimensional drawing of a 7SK80 (Terminalblock "D" with cap)

Other manuals for SIPROTEC 7SJ80

This manual suits for next models

Table of contents

Languages:

Other Siemens Control Unit manuals

Siemens

Siemens Desigo PXC4.E16 User manual

Siemens

Siemens SIMATIC FM 351 User manual

Siemens

Siemens SIRIUS 3RW44 User manual

Siemens

Siemens 4AI RTD User manual

Siemens

Siemens SINAMICS G130 User manual

Siemens

Siemens SIMATIC FM 450-1 User manual

Siemens

Siemens SINAMICS PM230 User manual

Siemens

Siemens IM 328-N Operating and installation instructions

Siemens

Siemens 599-02015 Owner's manual

Siemens

Siemens SIMATIC NET CP 343-2 User manual

Siemens

Siemens SIMATIC ET 200SP User manual

Siemens

Siemens Flowrite VF 599 Series Owner's manual

Siemens

Siemens HCP User manual

Siemens

Siemens SIMATIC NET RX1500 User manual

Siemens

Siemens SIMATIC ET 200S User manual

Siemens

Siemens XC1001-A Manual

Siemens

Siemens ZIC-4AC User manual

Siemens

Siemens SIRIUS 3RA2712 Technical Document

Siemens

Siemens SINAMICS S120 Technical Document

Siemens

Siemens SINAMICS S110 Datasheet

Siemens

Siemens RUGGEDCOM ROS User manual

Siemens

Siemens LMU54 Series Operator's manual

Siemens

Siemens A80407-01 User manual

Siemens

Siemens SIRIUS 3RT1.5 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual