Siemens HL 3000 User manual

This manual suits for next models

2

Table of contents

Other Siemens Accessories manuals

Siemens

Siemens SIWAREX JB User manual

Siemens

Siemens SITRANS WS300 User manual

Siemens

Siemens SITRANS F M MAG 1100 User manual

Siemens

Siemens 4292 Series User manual

Siemens

Siemens SIWAREX WT241 User manual

Siemens

Siemens Desigo QMX3.P44 User manual

Siemens

Siemens SITRANS CU02 User manual

Siemens

Siemens SIWAREX WP321 User manual

Siemens

Siemens QFA2000 User manual

Siemens

Siemens BS-240 Parts list manual

Siemens

Siemens SITRANS WS300 Service manual

Siemens

Siemens SIMATIC MOBY D User guide

Siemens

Siemens QFM2100 Service manual

Siemens

Siemens SITRANS WS100 User manual

Siemens

Siemens HC15 User manual

Siemens

Siemens QNA2 D Series Guide

Siemens

Siemens RUGGEDCOM WIN7014 User manual

Siemens

Siemens SITRANS F C MASS 2100 DI 1.5 User manual

Siemens

Siemens QAA4292.EWSC User manual

Siemens

Siemens SITRANS LR 400 Guide

Siemens

Siemens SITRANS WM300 MFA User manual

Siemens

Siemens QPM11 Series User manual

Siemens

Siemens RUGGEDCOM WIN7237 User manual

Siemens

Siemens QBM97 Series User manual

Popular Accessories manuals by other brands

Hillco

Hillco 2810 Operator's manual

Contours

Contours ZY024 manual

Saivod

Saivod VS621 manual

Virtuox

Virtuox VirtuCLEAN 2.0 user manual

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS user manual

Z-Wave

Z-Wave HSD-200Z user manual

turck

turck FMX-IM-2UPLI63FX quick start guide

Decagon Devices

Decagon Devices 10HS manual

UPPAbaby

UPPAbaby Cup Holder user manual

Elko

Elko SmartSensor Leakage Wireless manual

Grizzly

Grizzly H8371 instructions

Panasonic

Panasonic HG-T Series user manual

IFM Electronic

IFM Electronic Efector 250 Series Brief instructions

DigiDesign

DigiDesign 888/24 I/O installation guide

PROZIS

PROZIS QUAY user manual

patagonia

patagonia PSI Vest user manual

SFC Energy

SFC Energy EFOY GO! manual

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit instruction manual

Your

eye

in

hell

HL 3000 Manual

© Siemens Laser Analytics Sept 2000

Halogen lamp alignement manual

Document number: CID 3002-1103 Rev. 1A

LDS 3000 Operators manual HL 3002

1

1. HL 3002

1.1 General

Sometimes the visibility in the measurement path is poor. The reason for

this might be high dust load, smoke or strong ambient light from the

process (as in a combustion chamber). In this case a stronger light source

must be used in the first alignement step. Siemens Laser Analytics AB

can supply a suitable light source labelled HL 3000. This is a point source

using a 50 W halogen lamp and will produce a very luminous light spot -

normally easy to spot in the alignement procedure.

HL 3002 LDS 3000 Operators manual

2

1.2 The alignement procedure

The sensor is aligned using the sensor alignment kit AK 3002 together

with HL 3000. The aligning procedure is as follows:

Receiver side

1. Start by aligning the transmitter side. This is done by removing the

receiver at the quick connect interface and instead mount HL 3000

which defines the optical axis of the sensor pair. While the receiver is

dismounted - check that the lens is clean on the receiver and that the

purging is working.

Receiver side

HL 3000 generates a considerable amount of heat. Protective gloves should be ised

when it is handled.

Halogen alignement lamp

Note!

LDS 3000 Operators manual HL 3002

3

Transmitter side

2. Dismount the transmitter and check that the lens is clean on the

transmitter and that the purging is working. Then mount the trans-

mitter and twist-dismount the launcher (fiber cable connector in the

middle), twist-mount the cross hair instead. Align with the four bolts

on the flange, the light dot must be centred in the inner ring of the

cross hair.

Transmitter side

Cross hair

Alignement screws

HL 3002 LDS 3000 Operators manual

4

Transmitter side

3. Twist-mount the alignement lamp instead of the cross hair in the

transmitter.

Transmitter side

Alignement lamp

LDS 3000 Operators manual HL 3002

5

Receiver side

4. Mount the receiver back again and twist-mount the cross hair

instead of the detector module. Align with the four bolts on the

flange, the light dot must be centred in the inner ring of the cross

hair.

Receiver side

CD 3002 is now aligned and the holder for the fibre connector and the de-

tector module should be mounted in their places.

Finally, instrument air, or which ever method is used to protect the opti-

cal surfaces, should be connected to the appropriate inlets both at the

transmitter and receiver side of the sensor.

The mechanical stability of the sensor mechanics is sufficient to allow

dismounting (the quick connection) of both the receiver and the trans-

mitter. This means that cleaning of the lenses does not require re-align-

ment of the sensor.

Cross hair

Alignement screws

HL 3002 LDS 3000 Operators manual

6