Sidchrome SCMT26950 User manual

1 2 3 4 5

Dear Customers,

Thank you for purchasing our digital torque wrench. This manual will help you

to use the many features of your new digital torque wrench. Before operating

the torque wrench, please read this manual completely, and keep it

nearby for future reference

MAIN FEATURES

■ Head Interchangeable

■ Digital torque value readout

■ +/-2 % accuracy

■ +/-2 ° accuracy for 90° angle rotation

■ CW and CCW operation

■ Peak hold and track mode selectable

■ Buzzer and LED indicator for the 9 pre-settable target torques

■ Engineering units (N-m, ft-lb, in-lb, kg-cm, ‘‘°’’) selectable

■ 50 or 250 data memory for recall and joint torque auditing

■ Auto Sleep after about 2 minutes idle

■ Both AA and rechargeable batteries are compatible

NAMES AND FUNCTIONS OF PARTS A

1. LCD Display 9. Max. Value Index

2. Buzzer 10. Units(N.m, ft-lb, in.lb, kg.cm)

3. Communication Port 11. P(Peak hold mode) /T(Track mode)

4. Buttons 12. Clear Button

5. Battery Compartment 13. Max. Value Select

6. Battery Cover 14. Unit/Setting Button

7. LED Indicator 15. Up/Down Button

8. Torque / Angle value

7 8 10 13 15

9 11 12 14

N.m

E.316-30D - E.316-135D

E.316-200D - E.316-340D

Torque Accuracy *1 ±2%

Angle Accuracy *2 +/-2 ° for 90° angle rotation

Data memory size 250

PC Connectivity *3 Yes / USB

Pre-setting No. 9 sets

Bright LED 12 LED / 2 Red+10 Green

Operation Mode Peak Hold / Track

Unit Selection N.m, ft.lb, in.lb, kg.cm

Head Type Round Head Ratchet Insert

Button 2

Battery AA x 2

Battery Life *4

(Continuous operation)

60 hrs.

Battery Life *4

(Standby)

1 Year

Operating Tempe-

rature

-10°C ➜ 60°C

Storage Temperature -20°C ➜ 70°C

Humidity Up to 90% non-condensing

Drop Test 1 m

Vibration Test *5 10 G

Life time *6 10000 cycle

Environmental test *7 Pass

Electromagnetic

compatibility test *8

Pass

SPECIFICATIONS

Note:

*1: The accuracy of the readout is guaranteed from 20% to 100% of

maximum range + /- 1 increment. The torque accuracy is a typical value.

Calibration line is at the middle line of the dark spot on the rubber handle. For

keeping the accuracy, calibrate the wrench for a constant period time (1 year).

And the accuracy is based on the zero degree of offset from perpendicular drive.

*2: The angle accuracy is guaranteed at + /- 2° when rotating wrench to

90° at the speed of 30°/sec.

*3:

Use a special designed USB cable (accessory) to upload record data to PC.

*4: Use two AA batteries (Test condition: Toshiba carbon-zinc R6UG battery)

*5: Horizontal and vertical test

*6: One cycle means swing the torque wrench from 0 N.m to maximum

range and back to 0 N.m.

*7: Environmental test:

a. Dry heat e. Impact (shock)

b. Cold f. Vibration

c. Damp heat g. Drop

d. Change of temperature

*8: Electromagnetic compatibility test:

a. Electrostatic discharge immunity (ESD)

b. Radiated susceptibility

c. Radiated emission

➩

SPECIFICATIONS

ISO 6789 Type 2 Classe A Torque wrench precision : ± 2%

Precaution:

1. Communication function is only supported on some models. Check the

model no. and its speciﬁ cation before using communication function.

2. Do not insert the plug of communication cable into torque wrench that

does not support communication function.

CONNECTING COMMUNICATION CABLE

• Connect the accessory cable between the USB COM port of PC and

torque wrench.

UPLOADING RECORD DATA

• Make sure the connection between PC and wrench is normal.

• Press together to reset the wrench.

• Change the wrench operation mode to “Send”. (Refer to “Peak Hold

Mode Recorded Value Review ” section)

• Use PC to start the uploader program.

• In uploader program, ﬁ rst select the correct COM port No.

• Next, select the ﬁ le path to save the uploaded data.

• Finally, press “upload” button to transmit the torque records to PC.

• The uploaded data is then shown on the column and saved in the *.csv

ﬁ le. Use Microsoft Excel to view *.csv ﬁ le.

CAUTIONS:

Refer to the uploader program user guide for the detail operations

MAINTENANCE AND STORAGE

ATTENTION:

One-year periodic recalibration is necessary to maintain accuracy.

Please contact your local dealer for calibrations.

CAUTION:

Over-torque (110% of Max. torque range) could cause breakage or lose accuracy.

2. Do not shake violently or drop wrench.

3. Do not use this wrench as a hammer.

4. Do not leave this wrench in any place exposed to excessive heat,

humidity, or direct sunlight.

5. Do not use this apparatus in water.(not waterproof)

6. If the wrench gets wet, wipe it with a dry towel as soon as possible. The

salt in seawater can be especially damaging.

7. Do not use organic solvents, such as alcohol or paint thinner when

cleaning the wrench.

8. Keep this wrench away from magnets.

Do not expose this wrench to dust or sand as this could cause serious damage.

10. Do not apply excessive force to the LCD panel.

11. Apply torque slowly and graspe the center of the handle. Do not apply

load to the end of handle

BATTERY MAINTENANCE

When the wrench is not used for an extended period of time, remove the battery.

2. K

eep a spare battery on hand when going on a long trip or to cold areas.

3. Do not mix battery types or combine used batteries with new ones.

Sweat, oil and water can prevent a battery’s terminal from making elec-

trical contact. To avoid this, wipe both terminals before loading a battery.

5. Dispose of batteries in a designated disposal area. Do not throw

batteries into a ﬁ re.

COMMUNICATION

Instruction manual

NUen-E.316/0410

En France, pour tous renseignements techniques sur l'outillage à main,

téléphonez au : 01 64 54 45 14

BELGIQUE

LUXEMBOURG

FACOM Belgie B.V.B.A.

Egide Walschaertsstraat 14-16

2800 MECHELEN

BELGIQUE

✆

: +32 (0) 15 47 39 35

Fax : +32 (0) 15 47 39 71

NETHERLANDS FACOM Gereedschappen BV

Martinus Nijhofflaan 2

2624 ES DELFT

P.O. BOX 1007 . 2600 BA Delft

NETHERLANDS

✆ : 0800 236 236 2

Fax : 0800 237 60 20

DANMARK

FINLAND

ISLAND

NORGE

SVERIGE

FACOM NORDEN

Nordre Strandvej 119B

3150 HELLEBÆK

DENMARK

✆ : +45 49 76 27 77

Fax : +45 49 76 27 66

SINGAPORE

FAR EAST

FACOM TOOLS FAR EAST

N° 25 Senoko South Road

Woodlands East Industrial Estate

Singapore 758081

SINGAPORE

✆ : (65) 6752 2001

Fax : (65) 6752 2697

DEUTSCHLAND FACOM

Otto-Hahn-Straße 9

42369 Wuppertal

DEUTSCHLAND

✆ : +49 202 69 819-329

Fax : +49 202 69 819-350

SUISSE

ÖSTERREICH

MAGYARORSZAG

ČESKÁ REP.

FACOM WERKZEUGE GMBH

Ringstrasse 14

8600 DÜBENDORF

SUISSE

✆ : 41 44 802 8093

Fax : 41 44 802 8091

ESPAÑA

PORTUGAL

FACOM Herramientas S.L.

Poligono industrial de Vallecas

C/Luis 1°, s/n-Nave 95 - 2°Pl.

28031 Madrid

ESPAÑA

✆ : +34 91 778 21 13

Fax : + 34 91 380 65 33

UNITED

KINGDOM

EIRE

FACOM-UK

Europa view

SHEFFIELD BUSINESS PARK

ENGLAND

✆ : (44) 114 244 8883

Fax : (44) 114 273 9038

ITALIA SWK Utensilerie S.r.l.

Via Volta 3

21020 Monvalle (VA)

ITALIA

✆ : (0332) 790 381

Fax : (0332) 790 307

POLSKA FACOM Tools Polska Sp. zo.o.

ul.Modlińska 190

03-119 Warszawa

POLSKA

✆ : (48 22) 510 3627

Fax : (48 22) 510-3656

FRANCE &INTERNATIONAL

FACOM S.A.S.

6-8, rue Gustave Eiffel B.P.99

F-91423 Morangis cedex

FRANCE

✆ : 01 64 54 45 45

Fax : 01 69 09 60 93

http:/ /www.facom.com

Europa link

SHEFFIELD S9 1 XH

Stanley Deutschland GmbH

E.316-30D

845011

E.316-135D

845020

E.316-200D

845038

E.316-340D

845046

N.m

min. max.

ft.lb

min. max.

in.lb

min. max.

kg.cm

mini. max.

mm mm kg

E.316-30D 1,5 ➜ 30 1,11 ➜ 22,12 13,3 ➜ 265,5 15,3 ➜ 306,1 9 x 12 1/4’’ 360 1,52

E.316-135D 6,8 ➜ 135 5 ➜ 99,5 60 ➜ 1195 69 ➜ 1378 9 x 12

3/8’’

375 1,52

1/2’’

E.316-200D 10 ➜ 200 7,4 ➜ 147,5 88 ➜ 1770 102 ➜ 2041 14 x 18 1/2’’ 474 2,4

E.316-340D 17 ➜ 340 12,5 ➜ 250,7 150 ➜ 3009 173 ➜ 3469 14 x 18 1/2’’ 594 2,56

1 2 3 4 5

Dear Customers,

Thank you for purchasing our digital torque wrench. This manual will help you

to use the many features of your new digital torque wrench. Before operating

the torque wrench, please read this manual completely, and keep it

nearby for future reference

MAIN FEATURES

Head Interchangeable

Digital torque value readout

+/-2 % accuracy

+/-2 ° accuracy for 90° angle rotation

CW and CCW operation

Peak hold and track mode selectable

Buzzer and LED indicator for the 9 pre-settable target torques

Engineering units (N-m, ft-lb, in-lb, kg-cm, ‘‘°’’) selectable

50 or 250 data memory for recall and joint torque auditing

Auto Sleep after about 5 minutes idle

Both AA and rechargeable batteries are compatible

NAMES AND FUNCTIONS OF PARTS A

1. LCD Display 9. Max. Value Index

2. Buzzer 10. Units(N.m, ft-lb, in.lb, kg.cm)

3. Communication Port 11. P(Peak hold mode) /T(Track mode)

4. Buttons 12. Clear Button

5. Battery Compartment 13. Max. Value Select

6. Battery Cover 14. Unit/Setting Button

7. LED Indicator 15. Up/Down Button

8. Torque / Angle value

7 8 10 13 15

9 11 12 14

N.m

SCMT26950 - SCMT26951

SCMT26952

%2±1* ycaruccA euqroT

Angle Accuracy *2 +/-2 ° for 90° angle rotation

052ezis yromem ataD

PC Connectivity *3 Yes / USB

stes 9.oN gnittes-erP

Bright LED 12 LED / 2 Red+10 Green

Operation Mode Peak Hold / Track

Unit Selection N.m, ft.lb, in.lb, kg.cm

Head Type Round Head Ratchet Insert

5nottuB

2 x AAyrettaB

Battery Life *4

(Continuous operation)

60 hrs.

Battery Life *4

(Standby)

1 Year

Operating Tempe-

rature

-10°C 60°C

Storage Temperature -20°C 70°C

Humidity Up to 90% non-condensing

m 1tseT porD

G 015* tseT noitarbiV

elcyc 000016* emit efiL

Environmental test *7 Pass

Electromagnetic

compatibility test *8

Pass

SPECIFICATIONS

Note:

*1: The accuracy of the readout is guaranteed from 20% to 100% of

maximum range + /- 1 increment. The torque accuracy is a typical value.

Calibration line is at the middle line of the dark spot on the rubber handle. For

keeping the accuracy, calibrate the wrench for a constant period time (1 year).

And the accuracy is based on the zero degree of offset from perpendicular drive.

*2: The angle accuracy is guaranteed at + /- 2° when rotating wrench to

90° at the speed of 30°/sec.

*3:

Use a special designed USB cable (accessory) to upload record data to PC.

*4: Use two AA batteries (Test condition: Toshiba carbon-zinc R6UG battery)

*5: Horizontal and vertical test

*6: One cycle means swing the torque wrench from 0 N.m to maximum

range and back to 0 N.m.

*7: Environmental test:

a. Dry heat e. Impact (shock)

b. Cold f. Vibration

c. Damp heat g. Drop

d. Change of temperature

*8: Electromagnetic compatibility test:

a. Electrostatic discharge immunity (ESD)

b. Radiated susceptibility

c. Radiated emission

SPECIFICATIONS

ISO 6789 Type 2 Classe A Torque wrench precision : ± 2%

Precaution:

1. Communication function is only supported on some models. Check the

model no. and its speciﬁ cation before using communication function.

2. Do not insert the plug of communication cable into torque wrench that

does not support communication function.

CONNECTING COMMUNICATION CABLE

• Connect the accessory cable between the USB COM port of PC and

torque wrench.

UPLOADING RECORD DATA

• Make sure the connection between PC and wrench is normal.

• Press together to reset the wrench.

• Change the wrench operation mode to “Send”. (Refer to “Peak Hold

Mode Recorded Value Review ” section)

• Use PC to start the uploader program.

• In uploader program, ﬁ rst select the correct COM port No.

• Next, select the ﬁ le path to save the uploaded data.

• Finally, press “upload” button to transmit the torque records to PC.

• The uploaded data is then shown on the column and saved in the *.csv

ﬁ le. Use Microsoft Excel to view *.csv ﬁ le.

CAUTIONS:

Refer to the uploader program user guide for the detail operations

MAINTENANCE AND STORAGE

ATTENTION:

One-year periodic recalibration is necessary to maintain accuracy.

Please contact your local dealer for calibrations.

CAUTION:

Over-torque (110% of Max. torque range) could cause breakage or lose accuracy.

2. Do not shake violently or drop wrench.

3. Do not use this wrench as a hammer.

4. Do not leave this wrench in any place exposed to excessive heat,

humidity, or direct sunlight.

5. Do not use this apparatus in water.(not waterproof)

6. If the wrench gets wet, wipe it with a dry towel as soon as possible. The

salt in seawater can be especially damaging.

7. Do not use organic solvents, such as alcohol or paint thinner when

cleaning the wrench.

8. Keep this wrench away from magnets.

Do not expose this wrench to dust or sand as this could cause serious damage.

10. Do not apply excessive force to the LCD panel.

11. Apply torque slowly and graspe the center of the handle. Do not apply

load to the end of handle

BATTERY MAINTENANCE

When the wrench is not used for an extended period of time, remove the battery.

2. K

eep a spare battery on hand when going on a long trip or to cold areas.

3. Do not mix battery types or combine used batteries with new ones.

Sweat, oil and water can prevent a battery’s terminal from making elec-

trical contact. To avoid this, wipe both terminals before loading a battery.

5. Dispose of batteries in a designated disposal area. Do not throw

batteries into a ﬁ re.

COMMUNICATION

Instruction manual

SCMT26950

SCMT26951

SCMT26952

N.m

min. max.

ft.lb

min. max.

in.lb

min. max.

kg.cm

mini. max.

mm mm kg

SCMT26950 1,5 30 1,11 22,12 13,3 265,5 15,3 306,1 9 x 12 1/4’’ 360 1,52

SCMT26951 6,8 135 5 99,5 60 1195 69 1378 9 x 12

3/8’’

375 1,52

1/2’’

SCMT26952 10 200 7,4 147,5 88 1770 102 2041 14 x 18 1/2’’ 474 2,4

Instruction manual

The Stanley Works - 82 Taryn Drive

Epping Melbourne - Victoria

Australia 3076

Tel : 0384012000

Sidchrome.com.au

BEFORE USING THE WRENCH

BATTERY INSTALLATION B

•Remove the battery cover.

• Insert two AA batteries matching the -/+ polarities of the battery to

the battery compartment.

• Put on the battery cap and rotate it tightly according to the following

ﬁgures.

POWER ON AND RESETTING THE WRENCH

•Press to power on the digital torque wrench.

•Usually press to reset the digital torque wrench before using it.

ATTENTION:

If an external force is applied to the torque wrench during power-on/reset

or wake up period, an initial torque offset will exist in the memory.

ACTIVATION DURING SLEEP MODE

• The wrench will auto sleep after about 2 minutes idle for power

saving. Press to wake up the wrench during the sleep mode.

CAUTIONS:

During communication period (Send appears), the sleep function is disabled.

RESETTING THE WRENCH

• To reset the wrench, loosen the battery cap then tighten it to re-start.

• After reset, remember to press .

LOW BATTERY VOLTAGE PROTECTION

• If the battery serial voltage is under 2.3 volts, the wrench will display

a battery symbol and then turn off after a while.

SET UP

1 . Power On/Clear

2 . Unit Selection/Setting

3 . Up/Down Button

4 . Pre-Setting No.

STEP 1: PRE-SETTING NO.

Note:

1.If is appeared, that

means this wrench has ever been

applied more than 110% of maximum

torque.

2.The maximum capacity for

“Pre-setting No.” is 9 sets.

The “Pre-Setting No.” is in sequential.

STEP 2: UNIT SELECTION

N.m

123

N.m

Pre-setting: M1

N.m

Press

Pre-setting: M2

Pre-setting: M9

N.m

Pre-setting: Unit: N.m

in.lb

Press

ft.lb

Pre-setting: Unit: in.lb

Pre-setting: Unit: ft.lb

Press

kg.cm

Pre-setting: Unit: kg.cm

STEP 3: SET TORQUE VALUE

N.m

Pre-setting Torque Value

N.m

Press

N.m

Increase Max. Torque Value

Decrease Max. Torque Value

Note:

1.The “Unit Selection” is in sequential.

STEP 4: PEAK HOLD /TRACK

MODE SELECTION

N.m

Track Mode

Long Press

Set Peak/Track mode

Press

Record No.

Press

for selection

Set Peak/Track mode

Press

Clear Record

Press

N.m

Peak Hold Mode

Note:

1.Please skip this procedure and

continue to the next spet.

*Note 1

TRACK MODE OPERATION

N.m

Max. Target Value

N.m

((...((... ...))...))

N.m

START

(system initial)

*Note 1

Apply torque over 5 N.m

*Note 2

Current Torque Value

Over 80% of Max.

Target Value

N.m

MPT

Current Torque Value

((...((... ...))...))

Buzzer

Green LED

Over 80% of Set Torque

Approach

Max.

Target Value

(((((((( ))))))))

((((((((  )))))))

Buzzer

Red LED

Approach Max. Set Torque

Note:

1. If is appeared, that means this wrench has ever been

applied over than 110% of maximum torque.

2. When using track mode, if you apply torque over 5 N.m, the LCD

dispay will start to display the torque value. If the applied is less than

5 N.m, the LCD display does not have any value changes.

The smallest torque for E.316-30D series is 0.5 N.m.

3. The green LED will be on for 80%, 85%, 90%, 95% and 97.5% of

maximum setting torque.

4. The red LED will be on 99,5% of maximum setting torque.

PEAK HOLD MODE OPERATION

N.m

Max. Target Value

N.m

((...((... ...))...))

START

(system initial)

*Note 1

Apply torque

Current Max. Value

(Peak Hold)

N.m

((...((... ...))...))

Buzzer Green LED

Over 80% of Set Torque

Released

Apply torque

N.m

Recording

Flashing

*Note 2

Approach Max. Target Value

N.m

*Note 3

(((((((  ))))))) ((((((( ))))))))

Buzzer Red LED

Approach Max. Set Torque

Note:

1. If is appeared, that means this wrench has ever been

applied over than 110% of maximum torque.

2. If is appeared, that means the wrench’s memory is full and

the next value record can not be written in. Please refer the “Peak Hold

Mode Recorded Value Review” section to clear the momory data.

3. The green LED will be on for 80%, 85%, 90%, 95% and 97.5% of

maximum setting torque.

4. The red LED will be on for 99,5% of maximum setting torque.

PEAK HOLD MODE RECORDED VALUE REVIEW

N.m

Peak Hold/Track Mode

*Note 1

Long Press

(Clear)

Record Value

Set Peak/Track Mode

Auto Change

Record No.

*Note 2

Press

*Note 3

N.m

Press

Clear Record

Press

No Yes

Deleted

(give up)

Communication

*Note 4, 5, 6

Communication

Press

N.m

Peak Hold/Track Mode

(Exit)

Note:

1. The “Peak Hold” mode recorded value review also can be operated in

“Track” mode operation.

2. If you operate in the “Peak Hold” mode, the display will show

Pand please go to next step.

3. If the record is empty, it will show .

4. This function is not supported on all type of models.

5. Communication mode is for uploading record data to PC.

6. Communication mode is also for calibration of torque wrench. Please

contact your local dealer for more information.

ANGLE MODE OPERATION

((...((... ...))...))

Flashing

Angle Mode

*Note 1

Auto Change

Apply force and turn

*Note 2

*Note 3

Loose

*Note 5

Note 2:

1. When entering angle mode, the unit will be Degree.

2. When angle is in auto initial mode, please keep the wrench steady

without any disturbance.

3. After a while, the angle function will be in initiative mode with the

ﬂashing .

4. When loosing the wrench with angle mode, the display will show the

corresponding torque value with ﬂashing state.

5. The Green LED will be on with 80%, 85%, 90%, 95% and 97.5% of

target degree.

When reaching the target degree, the green and red LED will be on at the

same time.

Apply force and turn

Approach 80% of target degree

Current Angle

Press

Current Torque

N.m

*Note 4

Reach 80% of target degree

Apply force and turn

Approach target degree

Loose

Current Torque

N.m

*Note 6

((...((... ...))...))

Auto Change

Pre-setting Unit: N-m

Unit Selection: in-lb

Pre-seting Unit: ft-lb

Pre-setting Unit: kg-cm

Press

TORQUE UNIT SELECTION UNDER ANGLE MODE

Angle Mode

*Note 1

*Note 2

*Note 3

ft.lb

N.m

Long Press

Set Peak/Track Mode

in.lb

kg.cm

Press

Note:

1. The unit setting could be also entered from the torque mode.

2. Please skip the procedure and go to next step.

3. The unit selection is cyclic

*Note 4

*Note 3

*Note 4

N.m

Long Press

KEY LOCK

Lock on/off selection

Press

N.m

Auto Change

*Note

Note:

If ‘‘LoC on’’ is set, the display will show while pressing

, ,

Current Degree

This manual suits for next models

Other Sidchrome Power Tools manuals

Sidchrome

Sidchrome SCMTSA-1SHD User manual

Popular Power Tools manuals by other brands

AEG

AEG OMNI-JS Original instructions

SIP

SIP 01533 manual

Ribimex

Ribimex PRS499 quick start guide

3M Fiber Optic Connector Crimp Tool instructions

Ryobi

Ryobi P524 Operator's manual

ROJEK

ROJEK FSN 300A manual

Kemper

Kemper 1740PRO manual

WABCO

WABCO OptiTire installation manual

EINHELL

EINHELL TE-MS 18/210 Li Original operating instructions

Orgapack

Orgapack OR-T 85 Operating and safety instructions

TOUGHCUT

TOUGHCUT Diamond 400 instruction manual

Yaros

Yaros PB-3603 user manual

Fein

Fein BSS 2.0 E Repair instructions

Baileigh Industrial

Baileigh Industrial SS-2725 Operator's manual

Milwaukee

Milwaukee 2674-20 Operator's manual

Fein

Fein BLs 1.6 parts list

Princess

Princess Electric Multi Sharpener user manual

FOREDOM

FOREDOM K.1050 Operation & maintenance manual