Shure SM35-TQG User manual
SM35
Performance Headset Condenser Microphone
The Shure headworn electret condenser microphone, SM35, user guide.
Version: 3.0 (2022-F)
Shure Incorporated
3/6
1.
2.
3.
SM35
Performance Headset Condenser Microphone
SM35 Headworn Microphone
The Shure SM35 is a headworn electret condenser microphone, intended for use with a wireless bodypack transmitter in live
stage performances.
Wearing the Microphone
Install the windscreen on the microphone boom.
Place the headband around the back of the head, with the boom on the left side.
Place the microphone at the corner of the mouth. To decrease pops and plosives, avoid placing the microphone directly
in front of the mouth
Shure Incorporated
4/6
•
•
•
•
Note: Do not store the microphone in damp, enclosed spaces. Allow perspiration to dry completely before storing.
RPM400 Preamplifiers
The RPM400 preamplifiers offer exceptional dynamic range utilizing an active gain circuit in a concise and small package.
They are offered in two connector versions: TA4F and LEMO, which allows you to quickly take a wireless TL microphone and
make it a wired solution. These preamplifiers require phantom power and can efficiently operate across a wide range of supply
voltages from 12-48v.
Features
Active circuit design with neutral gain mimics wireless for consistent gain output across wired or wireless applications.
High RF immunity against unwanted interference.
Short, compact design.
Belt clip and table mounting kits for easy placement for a variety of applications.
Certifications
Note: Testingisbasedontheuseofsuppliedandrecommendedcabletypes.Theuseofotherthanshielded(screened)cabletypesmaydegradeEMCper
formance.
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Global Compliance
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
www.shure.com
Specifications
Type
Electret Condenser
Frequency Response
40Hzto20,000Hz
Shure Incorporated
5/6
Polar Pattern
Unidirectional (Cardioid)
Output Impedance
100Ω,@1kHz
Sensitivity
57.8dBV/Pa,@1kHz,1000Ωload
Signal-To-Noise Ratio [1]
59.2dB,@1kHz,1000Ωload
Maximum SPL [1]
151.3dB,1000Ωload,@1kHz,1%THD
Dynamic Range [1]
116.5dB,@1kHz,1000Ωload
Self Noise [1]
34.8dBSPLA,1000Ωload
Power Requirements
TA4F +5VDC(nominal),10Vmaximum(DCbias)
XLR connector 12to52VDC,phantompower
Polarity
TA4F Positive pressure on diaphragm produces positive
voltage on pin 3 with respect to pin 1
XLR Positive pressure on diaphragm produces positive
voltage on pin 2 with respect to pin 3
Cable
1.1m (45in.)
Connector
TA4F or XLR
Weight
72g(2.53oz.)
[1] Measurements taken using RPM400 preamp
*All specifications measured with a 48 Vdc phantom power supply. The microphone operates at lower voltages, but with slightly
decreased headroom and sensitivity.
Shure Incorporated
6/6
Accessories
Furnished Accessories
Replacement Kit with Clip + 2 Snap-Fit Foam Windscreens for SM35 RK378
TA4F/TQG XLR Preamplifier RPM400TQG
Replacement Parts
Black Snap-Fit Foam Windscreens (4) for SM35, BETA98, BETA98A, BETA98/S,
BETA98D/S, BETA98H/C, MX183, MX184, MX185, MX202, WH30, WL183, WL184 and
WL185
RK183WS
This manual suits for next models
1
Table of contents
Other Shure Microphone manuals
Shure
Shure Controlled Magnetic 444D Owner's manual
Shure
Shure Microflex MX415DUAL User manual
Shure
Shure WL50 User manual
Shure
Shure LEGENDARY PERFORMANCE MV88 User manual
Shure
Shure 522 User manual
Shure
Shure Microflex MX300 series User manual
Shure
Shure Microflex MX100 Series User manual
Shure
Shure KSM137 User manual
Shure
Shure M2 Owner's manual
Shure
Shure 16A User manual
