Shure UA864 User manual

1/10

UA864 -- Wall-Mounted Active Directional

Antenna

General Description

The UA864 antenna provides active directional RF coverage in an easy-to-install, low-profile enclosure that can be

mounted on walls, ceilings, or metal surfaces with improved reception. The paintable, neutral white housing allows

the antenna to blend into corporate or classroom settings. The 4-position selectable gain switch provides attenua-

tion and boost settings to match the antenna to the environment. UHF variants provide wideband RF coverage.

Features

•Low-profile design

•Wall or ceiling mounting options

•Wideband performance (UHF models only)

•Four-position gain switch

•Metal surface mounting capability

•LED indicators for gain settings

•Neutral white, paintable housing

Positioning Antennas for Diversity Reception

The UA864 is a polarized antenna and must be oriented correctly to optimize reception for each transmitter type.

The gain switch indicates the antenna's orientation. Position the antennas using the following guidelines:

Note: The antenna's inner construction may differ for each model variation.

Handheld and Bodypack Transmitters (vertical)

Shure Incorporated

2/10

Boundary Microphones (horizontal)

Mixed Transmitter Types (vertical and horizontal)

Antenna Placement

Use the following guidelines when mounting antennas:

•Antennas and receivers must cover the same frequency range.

•Mount antennas at least four feet apart for optimal diversity.

•Position antennas so there is nothing obstructing a line of sight to the transmitter (including the audience).

Find More Information Online

For more information, visit http://www.shure.com

Installation

Mounting on a Wall or Ceiling

The mounting plate installs directly to a wall, ceiling, or a standard junction box.

Shure Incorporated

3/10

Required Equipment

•#8 or #6 screws

•Flat washers

•Lock washers

•Drill

•Screwdriver

Installation Steps

1. Align the mounting plate:

Junction box mounting: Align the mounting plate with the junction box so that at least two screws can be

used.

Wall mounting: Use the mounting plate as a template to mark the location for the holes on the mounting sur-

face. Drill the holes accordingly.

2. Secure the mounting plate to the surface with the washers as shown (CAUTION: Do not over-tighten screws).

3. If running RF cable from inside the wall, guide it through the opening in the mounting plate and connect the ca-

ble to the antenna output.

4. Position the antenna mounting posts over the keyhole slots in the mounting plate and slide it into the locked

position.

Mounting to a wall or ceiling

Mounting to an electrical junction box

Shure Incorporated

4/10

Securing the antenna to the mounting plate

Routing the Cable

The output connector can be routed through ports 1or 2on the antenna. When connecting to an RF cable in the

wall, run the cable through the opening in the mounting plate.

Rotating the Cover

The cover can be detached and rotated in any direction for a matched appearance when using multiple antennas.

1. Remove the screws holding the cover in place from the back of the antenna

2. Remove the cover and rotate to the desired position

3. Replace the screws to secure the cover

Painting the Antenna

The cover of the antenna can be painted to match the installation environment. Use the following guidelines when

painting the antenna cover:

•Remove the antenna cover before painting

•Only use non-metallic paint, as any metallic content may interfere with RF reception

•Allow the paint to dry completely before reinstalling the cover

Shure Incorporated

5/10

•Avoid painting in the screw holes

Warning: Do not touch the internal components of the antenna when the cover is removed.

Connecting to a Receiver

This antenna is compatible with any receivers, distribution systems, and splitters that operate within the antenna's

frequency range. For receivers with multiple antenna ports, connect each antenna being used to a separate port.

Note: The antenna requires bias voltage from the receiver or distribution system to operate and for LED function-

ality. If these devices do not supply bias voltage, the Shure UABIAST inline power supply can be used.

Setting the Gain Switch

Use the gain switch to optimize antenna performance for the RF characteristics of the room or location. Monitor

the RF signal from the receiver to ensure optimal signal strength.

RF Gain Set

ting (dB) Use Scenario

Pad: −10, −20 Provides increased isolation from other RF sources when the desired wireless microphone

signal strength is strong. If the RF OVERLOAD LED illuminates when using a higher gain

setting, the pad should be used to attenuate the signal, but only after verifying that the trans-

mitter is an appropriate distance from the antenna.

0 (Default) Suitable for typical room installations and provides enough RF gain in most cases when ca-

ble runs are between 10 and 50 feet.

Boost: +10 Provides an extra 10 dB of RF gain to compensate for signal loss if using long cable runs (50

feet or more).

Note: Bias power supplied by receiver antenna ports or an external power source is required for antenna to oper-

ate and for illuminating the LEDs.

Selecting Antenna Cables

Use 50 ohm low-loss coaxial cable, such as RG-8U. Shure offers pre-terminated antenna cables ranging from 6 to

100 feet.

NOTE: When ordering cables from Shure, select the low-loss "Z" models (available for longer cables) when using

frequency bands above 1000 MHz.

Shure Incorporated

6/10

Cable Maintenance

To maintain top performance for antenna cables:

•Avoid sharp bends or kinks in the cables.

•Do not deform cables with makeshift clamps, such as bending a nail over the cable.

•Do not use in permanent outdoor installations.

•Do not expose to extreme moisture.

Specifications

Connector Type

BNC, Female

Impedance

50 Ω

Power Requirements

10 to 15 V DC bias from coaxial connection, 75 mA

RF Frequency Range

UA864US 470–698 MHz

UA864LO 470–698 MHz

UA864HI 530–790 MHz

UA864A 650–952 MHz

UA864Z16 1240–1260 MHz

UA864Z17 1492–1525 MHz

UA864Z18 1785–1805 MHz

Reception Pattern

3 dB Beam Width at center frequency

UA864US 100 degrees

UA864LO 100 degrees

UA864HI 95 degrees

Shure Incorporated

7/10

UA864A 90 degrees

UA864Z16 70 degrees

UA864Z17 70 degrees

UA864Z18 70 degrees

Third-order Overload Intercept Point (OIP3)

>30 dBm

Antenna Gain

On Axis, 0 dB Gain Setting at center frequency

UA864US 2.5 dBi

UA864LO 2.5 dBi

UA864HI 3.0 dBi

UA864A 5.5 dBi

UA864Z16 7.5 dBi

UA864Z17 6.5 dBi

UA864Z18 4.5 dBi

Signal Gain

±1 dB, Switchable

+10 dB0 dB−10 dB−20 dB

RF Overload LED Threshold

−15 dBm

Dimensions

176 x 176 x 51 mm (H x W x D)

Weight

UA864 487 g (17.2 oz.)

UA864Z 454 g (16 oz.)

Shure Incorporated

8/10

Operating Temperature Range

−7°C (20°F) to 49°C (120°F)

Storage Temperature Range

−29°C (-20°F) to 74°C (165°F)

Certifications

This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking.

The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance

Authorized European representative:

Shure Europe GmbH

Headquarters Europe, Middle East & Africa

Department: EMEA Approval

Jakob-Dieffenbacher-Str. 12

75031 Eppingen, Germany

Phone: +49-7262-92 49 0

Fax: +49-7262-92 49 11 4

Email: [email protected]

Shure Incorporated

9/10

Polar Pattern

Shure Incorporated

10/10

Other manuals for UA864

Table of contents

Popular Antenna manuals by other brands

Alfa Network

Alfa Network APA-L01 Specifications

Naval

Naval PR-422CA Operation manual

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series manual

TERK Technologies

TERK Technologies TV44 owner's manual

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK quick start guide

HP J8999A instructions

MobilSat

MobilSat MSP-S Mounting instructions

Steren

Steren ANT-UHF 13 instruction manual

Novatel

Novatel 600-G User information

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna owner's manual

TRENDnet

TRENDnet TEW-AO12O Specifications

Radio Shack

Radio Shack 15-1837 owner's manual

CommScope

CommScope CMAX-OMFX-43M-I53 Installation instruction

Ramsey Electronics

Ramsey Electronics DAP25 Kit assembly and instruction manual

COBHAM

COBHAM SAILOR 800 VSAT Replacement procedure

Trango Systems

Trango Systems AD900-9 Specification sheet

Steren

Steren ANT-100 user manual

Proxim

Proxim 5054-PA-23 quick start guide