Shopify EVP-3PH User manual

FEATURES

TECHNICAL DATA

SAFETY PRECAUTIONS

1. The device must be installed by a qualiﬁed person,

2. Disconnect all power before working on the device. Don’t touch any terminal

when the power is ON.

3. Verify correct terminal connection when wiring.

4. Don’t dismantle or repair the device whether it operates normally, otherwise

no responsibility is assumed by producer and seller.

5. Never use the device at the site which can be invaded by corrode gas, strong

sunshine light and rain.

6. Clean the device with a dry cloth.

7. Fail to follow these instructions will result in serious injury or death.

3 PHASE VOLTAGE AND CURRENT PROTECTOR

EVP-3PH

Please read complete instructions prior to installation and operation of

the device.

Microcontroller based

Digit display for operating voltage and current value

Protect electrical device against over/under voltage, overcurrent,

three phase asymmetry and incorrect phase sequence.

Voltage measurement accuracy =1%

Parameters setting by keys

LEDs indication for over/under voltage and over current faults

5 Module, DIN Rail mounting

≤50% at 40°C(without condensation)

-1-

Iset<Ir<80A:Ta; Ir=80A: ≤0.1s

Overcurrent setting range 5A~63A

Phase sequence setting

Asymmetry setting range

Hysteresis

Auto reset setting

Asymmetry trip delay

Ts:5s~600s

Ta:5s~600s

OFF-1~20

ON-OFF

ON/OFF

20V~99V-OFF

0.1s; ≤350V:0.02s

≤120V:0.5s ,<120V:0.1s

10s

450V

Protection degree IP20

Pollution degree 3

Electrical life

Altitude

Operating temperature

Storage temperature

Mechanical life

10 5

106

≤2000m

-5°C~40°C

-25°C~55°C

Voltage measurement accuracy ≤1%(over the whole range)

Rated insulation voltage

Humidity

Output contact 1NO

Operation voltage range

AC 50V~400V

Rated frequency

50/60Hz

220~300V

AC 220V

Overvoltage(U>) setting range

Undervoltage(U<) setting range

Rated supply voltage

120~210V

Undervoltage(U<) trip delay

Reset/start delay

Overvoltage(U>) trip delay

Overcurrent(I>) trip delay

* Operating current value

Overcurrent faults trip delay range

Continuous overcurrent times setting

Overvoltage and asymmetry: 5V

Undervoltage:3V

ON-OFF

Phase sequence protection

ON-OFF ON

220V~300V

120V~210V

5s~600s

5A~63A

20V~99V-OFF

OFF-1~20

5s~600s

250V

170V

63A

50V

OFF

15s

Asymmetry trip value

Continuous overcurrent faults times

Auto reset setting

Overcurrent trip delay

Setting range

Step Factory setting

Overvoltage trip value

Reset/start delay

Undervoltage trip value

Technical parameter

Overcurrent trip value

FRONT-FACE PANEL

Digit+/Inquiry of

last fault

Display

Menu selection

Manual ON/OFF

Digit-

Reset/

AAA

VVV

L1 L2 L3

Switch on/oﬀ manually

Press the key for

more than 0.5s

>0.5s

L1 L2

:Synchronous mode; :Asynchronous mode

Operation mode

Output indicator

Inquiry of faults

Display the last fault value and ﬂash.

Exit from display after 3s.

Main menu setting

>2s

L3 main display

End setting, press OK to exit from

settings

In=63A

Only L3 display when setting. L1 and L2 don’t display.

Overvoltage trip value setting V

Change the setting value by pressing

keys.

Undervoltage trip value setting V

Change the setting value by pressing

keys.

Reset/start delay setting S

Change the setting value by pressing

keys.

Overcurrent value setting A

Change the setting value by pressing

keys.

Overcurrent faults trip delay setting S

Change the setting value by pressing

keys.

Asymmetry ratio setting V

Change the setting value by pressing

keys.

Continuous overcurrent faults times

setting

Change the setting value by pressing

keys. OFF: turn off the function.

Phase sequence setting

Change the setting states by pressing

keys.

OFF: turn off the function;

ON: turn on the function;

Auto reset setting

Change the setting states by pressing

keys.

OFF: turn off the function;

ON: turn on the function;

Long press can increase or decrease repidly.

The relay will automatically exit from the menu and not save the

modiﬁed value if not pressing the keys for continuous 60s during

setting.

-2-

Operation mode setting

Change the setting states by pressing

keys.

:Synchronous mode;

:Asynchronous mode

:Synchronous mode; In this mode the

device works as a three phase voltage

protector with N,L1,L2,L3 as single

circuit

:Asynchronous mode : In this mode the

device works as three Individual single

phase protectors which can be

connected to three separate circuits.

Also the device can identify & stop/trip/

reset each of the three circuits

independently

i.e "N - L1" & "N - L2" & "N - L3"

( Modes explained in the bottom tab )

Voltage operating values display on upper L1-L2-L3 and

synchronous over voltage faults code display on the lower

L1-L2- L3

U> faults display(synchronous)

VVV

AAA

Voltage operating values display on upper L1-L2-L3 and

asynchronous over voltage faults code display on the lower

L1-L2- L3

U> faults display(asynchronous)

VVV

AAA

U< faults display(synchronous)

VVV

AAA

U< faults display(asynchronous)

VVV

AAA

Reset/start delay display(synchronous)

VVV

AAA

Reset/start delay display(asynchronous)

VVV

AAA

I> faults display(synchronous)

VVV

AAA

I> faults display(asynchronous)

VVV

Display of phase sequence fault

VVV

AAA

Voltage operating values display on upper L1-L2-L3 and

asymmetry fault code display on lower L2 during the counting of

start delay; After the delay is over, the output relay closes.

Display of (only synchronous)asymmetry fault

VVV

AAA

Display of (synchronous)continuous I> faults

VVV

AAA

Display of (asynchronous)continuous I> faults

Display for continuous overcurrent faults after reset/start delay is over.

overcurrent faults times is more than preset times.

VVV

A AA

Voltage operating values display on upper L1-L2-L3 and delay

time flashes on the lower L3 during the counting of start delay; After

the delay is over, the output relay closes.

Voltage operating values display on upper L1-L2-L3 and delay

time flashes on the lower L1-L2- L3 during the counting of start

delay; After the delay is over, the output relay closes.

Voltage operating values display on upper L1-L2-L3 and

synchronous under voltage faults code display on the lower

L1-L2- L3

Voltage operating values display on upper L1-L2-L3 and

asynchronous under voltage faults code display on the lower

L1-L2- L3

Voltage operating values display on upper L1-L2-L3 and

synchronous over current faults code display on the lower

L1-L2- L3

Voltage operating values display on upper L1-L2-L3 and

asynchronous over current faults code display on the lower

L1-L2- L3

Display for continuous overcurrent faults after reset/start delay is over.

overcurrent faults times is more than preset times.

Start the relay after reset manually.

Disconnect the overload device

Start the relay after reset manually.

Disconnect the overload device

Display L1-L3-L2 when phase failure fault occurs. User can

change the position of L2 and L3 after disconnected supply.

-3-

Manual reset

Auto reset function is off.

0.1s

Ton Ton Ton

0.5s

Iset

Imax

Ton Ton 0.1s Ton

Asy

10s

<10s

The device will begin counting of reset/start delay after reset for

faults.

OPERATING INSTRUCTIONS

O-OFF O-OF F O-OF FO-OFF

L1 L2 L3N

N L1 L2 L3

123 4

567 8

N L1 L2 L3

A A A

V V V

L1 L2 L3

SYMBOL

WIRING DIAGRAM

Rated operating current of circuit breaker is 75% maximum current of the relay

Ie=0.75x Imax

LOAD

Overvoltage and undervoltage

Hys(U> -5V)

Hys(U< +3V)

U< threshold

U> threshold

Overcurrent

Asymmetry

Ts: Reset/start delay

Ta: Overcurrent faults trip delay

FUNCTION DIAGRAMS

If a voltage fault was detected when the reset/start delay of relay is

counting, the output relay opens and faults indication LED lights up.

Voltage faults: if input voltage was detected to have returned to Hys

after tripped for voltage faults, the relay will reset automatically and

begin the counting of reset/start delay.

Current faults: After the relay tripped for current faults, it will reset

automatically begin the counting of reset/start delay.

The operating voltage and current values will be displayed on screen

when the relay is operating normally. If a voltage or current fault was

detected, the output relay opens and faults code display.

L1 L2

-4-

DIMENSIONS

N L1 L2

123

567

89.5

65.5

>0.5s

A A

Popular Surge Protector manuals by other brands

ELAC

ELAC ProteK PR91-W Setup guide

Tsubaki

Tsubaki TSM4000M1 instruction manual

QVS

QVS PP134C Specification sheet

CyberPower

CyberPower CSP604T user manual

Davis Instruments

Davis Instruments Radio Surge Protector user guide

M-system

M-system MGA-100 instruction manual

CyberPower

CyberPower CSP706T user manual

CyberPower

CyberPower B300WRC1 user manual

M-system

M-system MGD-24 instruction manual

Leviton

Leviton 51120-3R Installation

Panamax

Panamax MAX 5400-EX owner's guide

CyberPower

CyberPower B1006T user manual

OBO Bettermann

OBO Bettermann ÜSM-20-230I1PE65 installation instructions

Minuteman

Minuteman MMS7120RCT user guide

Leviton

Leviton 52412-DS3 installation instructions

Savio

Savio LZ-07 user manual

Siemens

Siemens HNM3M120 manual

Mitsubishi Electric

Mitsubishi Electric LITOL LTM-125RF manual