Sharp PN-R606 User manual
PN-R606 Dismantle Instruction
1
Dismantle Instruction
LCD MONITOR
MODEL
PN- R606
PN-R606 Dismantle Instruction
2
Table of contents
1. Scope.................................................................................................................. 3
2. Tools for dismantling............................................................................................... 3
3. Dismantle Procedure .............................................................................................. 3
4. Back covers .......................................................................................................... 4
5. Printed circuit boards ............................................................................................. 5
6. Battery................................................................................................................ 5
7. LCD Module .......................................................................................................... 6
8. Capacitors............................................................................................................ 7
9. Parts List ............................................................................................................. 7
PN-R606 Dismantle Instruction
3
1. Scope
This document describes dismantling instruction according to Annex VII of Directive 2012/19/EU.
2. Tools for dismantling
Below tools are required to dismantle this product.
- Screw Driver
- Nipper
3. Dismantle Procedure
This product can be dismantled by below steps.
1. Remove Back covers (section 4)
2. Remove the shielding
3. Remove Printed circuit boards (section 5)
4. Remove Battery (section 6)
5. Dismantle LCD (section 7)
6. Remove Electrolyte Capacitors (section 8)
PN-R606 Dismantle Instruction
4
4. Back covers
Back cover can be removed by screw driver.
PN-R606 Dismantle Instruction
5
5. Printed circuit boards
All PWBs can be removed by screw driver.
Main I/F PWB (1pcs) Power PWB (1pcs) LED driver PWB (1pcs)
T-CON PWB (1pcs) OPS PWB (1pcs)
6. Battery
This model uses AAA battery for remote control and CR2032 Lithium Coin battery on Main I/F PWB.
-The remote control battery can be easily removed.
-The battery CR2032 on the main I/F PWB can be easily removed from the battery holder.
PN-R606 Dismantle Instruction
6
7. LCD Module
- LCD Dismantle procedure
1. Remove Rear cover
2. Remove PWBs and Tray
3. Remove the Cables
LCD
PN-R606 Dismantle Instruction
7
8. Capacitors
Electrolyte Capacitors which diameter/height is larger than 25mm is installed on Power PWB.
These capacitors can be removed by using nipper to cut the leads.
On Power PWB
9. Parts List
Parts described in Annex VII of directive 2012/19/EU are as below.
Parts
Note
LCD
60inch LCD module
Printed Circuit Boards
Main I/F PWB
Power PWB
LED driver PWB
T-CON PWB
OPS PWB
Battery
AAA battery
Lithium Coin Battery CR2032
Electrolyte capacitors
(height >25mm, diameter >25mm)
On Power PWB
External electric cables
2 kinds of Power Cord
- for EU
- for UK
Table of contents
Other Sharp Monitor manuals
Sharp
Sharp PN-S655 User manual
Sharp
Sharp PN-U553 User manual
Sharp
Sharp MZ-1D05 User manual
Sharp
Sharp 8M-B32C1 User manual
Sharp
Sharp LL-T1501A User manual
Sharp
Sharp AQUOS LB-1085 User manual
Sharp
Sharp PN-K322B User guide
Sharp
Sharp PN-Q901 User manual
Sharp
Sharp PN-L652B User manual
Sharp
Sharp PN-V550A User guide
Sharp
Sharp PN-CD701 Instruction sheet
Sharp
Sharp PN-525U User manual
Sharp
Sharp LCD MONITOR User manual
Sharp
Sharp LL-151-3D User manual
Sharp
Sharp PN-V601A User guide
Sharp
Sharp PN-V601A User manual
Sharp
Sharp PN-S525 User manual
Sharp
Sharp PN-L702B User manual
Sharp
Sharp PN-E603 User guide
Sharp
Sharp PN-HE751 User guide
