Sharp LCD MONITOR User manual
Applicable models
LL-P202V/LL-S242A
LCD MONITOR
TOUCH DISPLAY DRIVER 2
OPERATION MANUAL
Version 1.0
for Mac
2
E
Contents
Introduction......................................................................3
System Requirements..................................................3
Setting up the Computer.................................................4
Install............................................................................4
Touch Panel Settings.......................................................5
How to congure settings.............................................5
Calibration ....................................................................7
Properties.....................................................................8
Pen Settings (LL-P202V Only) ......................................10
Digitizer pen ...............................................................10
Uninstall..........................................................................12
Touch Action ..................................................................13
Important Information
• This software has been shipped after strict quality control and product inspection. If, however, you nd any failure or
malfunction, contact your product dealer.
• Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a
third party, nor for any other malfunctions or damage to this software arising during use, except where indemnity liability is
recognized under law.
• Transcribing or duplicating part or all of this manual and/or this software without permission from our company is not
permitted.
• As a part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for
product improvement without prior notice.
• The contents or details may vary depending on the screen conguration and OS version, etc.
• This manual does not contain basic operating instructions for Mac OS.
Trademarks
• Apple, Mac and Mac OS are registered trademarks of Apple Inc.
• Intel is a trademark or registered trademark of Intel Corporation or its subsidiaries in the U.S.A. and other countries.
• All other brand and product names are trademarks or registered trademarks of their respective holders.
3E
Introduction
System Requirements
The touch display driver 2 is a program that enables you to use the touch panel to operate the computer that is connected to the
touch panel.
To use the touch panel, the touch panel must be connected to a computer, and the touch display driver 2 must be installed on
the computer.
OS Mac OS X v10.7, Mac OS X v10.8, Mac OS X v10.9
CPU Intel processor
Memory At least 2 GB
Free space on hard drive At least 5 MB
TIPS
• Depending on the application software, touch operation may not be possible or differ from mouse operation (for example, if
the application processes mouse and other operations independently).
4
E
Setting up the Computer
Install
Caution
• To install, an administrator name (user name) and password are required.
• If an older version of the touch display driver 2 is installed, remove (uninstall) the old version before installing the touch
display driver 2. (See page 12.)
• Do not touch the touch panel when connecting the USB cable.
If you touch the touch panel, it will lead to a malfunction. In this case, disconnect and then reconnect the USB cable.
1. Start your computer.
2. Exit all applications that are running.
3. Connect the USB cable for the touch panel to the computer.
Touch Panel port
USB cable (Supplied)
To the USB terminal
of the PC
4. Run the setup program.
(1) Double-click the “TouchDisplay” folder, and then double-click the “Mac” folder.
(2) Double-click “SharpTouchDisplay2.pkg”.
5. Click “Continue”.
Follow the on-screen instructions to install the driver.
• If a screen prompting you to enter the name and password appears, enter the name and password of the administrator
and click “Install Software” (or “OK”).
• If the “When this software nishes installing, you must restart your computer. Are you sure you want to install the software
now?” screen appears, click “Continue Installation”.
6. Whentheinstallationnishedscreenappears,click“Restart”.
This completes the installation of the touch display driver 2.
Each time the computer is started, the touch display driver 2 will start automatically to enable the touch panel to be used.
5E
Touch Panel Settings
The touch display driver 2 starts automatically and the icon ( ) appears on the menu bar.
Caution
• If LL-P202V and LL-S242A are connected at the same time, a screen for selecting the model will appear each time you select
a setting.
• Depending on the connected model, the screen image is different.
• Default value may vary according to the models.
Howtoconguresettings
nConguringsettingsfromthemenubar
1. Click the touch display driver 2 icon ( ) on the menu bar.
2. Click a menu to change a setting.
• Current Resolution: The model currently being used and the current screen resolution appear.
• Calibration: See page 7.
• Properties: See page 8.
• Hardware Information: Select this to specify “Rotate Mode”.
- Rotate Mode:
To correct the touch position when the screen is rotated, select the screen angle from the following:
Standard (0°) / 90° / 180° / 270°
• Digitizer pen (LL-P202V only): See page 10.
• Version Information: Shows the version of the touch display driver 2.
• Disable TD Driver:
Select to disable the touch panel function.
To disable a single touch panel function, see “Function Setting”. (See page 9.)
nConguringsettingsfromSystemPreferences
1. Click “System Preferences” from the Apple menu ( ).
2. Click “SharpTouchDisplay2”.
3. Click the menu and select settings.
Menu
TIPS
• If the “Show Setting Utility in menu bar” checkmark is removed, the touch display driver 2 icon ( ) does not appear on the
menu bar.
6
E
nSettings when two devices are connected at the same time
• If two displays of the same model are connected, touch operation will only be enabled on one model.
• If LL-P202V and LL-S242A are connected at the same time, select the model to apply the touch panel settings to.
* Two models cannot be set at the same time.
1. Click “System Preferences” from the Apple menu ( ).
2. Click “SharpTouchDisplay2”.
The “Device Selection” screen appears.
3. Select the model whose settings you want to change.
Touch Panel Settings
7E
Calibration
If black bands appear at the top and bottom or left and right of the screen, perform position adjustment so that the mouse cursor
correctly moves to the point that is touched.
* If black bands appear both at the top and bottom and at the left and right, the touch position is not correct. In this case, change
the display.
nCalibration Method
Follow the steps below to congure the setting.
1. Click the touch display driver 2 icon ( ) on the menu bar.
2. Click “Calibration”.
Auto
If black bands appear on the screen, position adjustment is automatically performed.
Select “Auto” and click on “Apply”.
Manual
If the automatically adjusted touch position is not correct, enter the display resolution (Width, Height) and click “Apply”.
To check the monitor resolution, touch “Input Select” in the menu screen of the touch display. The resolution will be shown in the
screen that appears.
For details, see the LCD MONITOR manual.
Touch Panel Settings
8
E
Properties
Settings for the touch action can be congured in the properties.
nDouble Click Range
Set the range over which the position can shift between the rst touch and the second touch and still be recognized as a double-
click (“Narrow” (8 pixels) to “Wide” (64 pixels)). To return the setting to the default setting, click “Default” (32 pixels).
nDouble Click Speed
Set the time that is recognized as a double-click. When a second touch occurs within the set time after the rst touch, it is
recognized as a double-click.
Speed Setting (Auto)
The inside of the frame can be touched twice (double-clicked) to set the speed automatically based on the interval between the
touches.
Set Manually
The speed can be set manually from “Slow” (about 1 second) to “Fast” (about 0.3 seconds).
Test
When the inside of the frame is double-clicked by touching it twice, the screen changes. If the screen does not change, repeat
the setting.
Default
Click to restore the default setting.
TIPS
• Depending on the application software, changing the setting may not have any effect (for example, if the setting is set
separately in the application).
Touch Panel Settings
9E
nSecondary click
You can set press and hold to be recognized as a secondary click.*
Enable press and hold for secondary click
When the checkbox is selected, press and hold is recognized as a secondary click.
Press and Hold Duration
Set the time until press and hold is recognized as a secondary click (“Short” (0.5 sec) to “Long” (1.5 sec)).
Press and Hold Effective Range
Set the effective range for determination that the screen is being touched continuously (“Narrow” (0 pixels) to “Wide” (20 pixels)).
* If the Mac OS left-click long press action interferes with the press and hold action, do the following:
• Use “Click or tap with two ngers”
• Adjust “Press and Hold Duration” to a longer setting (toward “Long”)
nFunction Setting
Select the touch action to be used. (See page 13.)
Touch actions that are followed with a mark have multiple actions that can be used. Click a touch action and selected the
desired action.
Caution
• Touch actions that can be used vary depending on the OS.
*
* OS X v10.8/v10.9 only
Touch Panel Settings
10
E
Pen Settings (LL-P202V Only)
Digitizer pen
Settings for the digitizer pen can be congured.
nButton Settings
Assign functions to the function buttons of the digitizer pen.
The factory default settings are shown below.
Button action Function
Function button 1 Press and release button1 *1Secondary click
Press button1 and move *2Scroll
Function button 2 Press and release button2 *1Undo
Press button2 and move *2Rotate
The functions below can be assigned to Function button 1 and Function button 2.
Button action Function
Press and release button1/Press and release button2 Secondary click, Look up, Undo, Redo, Back, Forward, PageUp, PageDown,
Disable
Press button1 and move/Press button2 and move Scroll, Rotate, Zoom in or out, Shift, Option, Command, Show Desktop,
Disable
*1 Press and release the button without moving the pen (screen touch or hover action)
*2
Move the pen while holding down the button (screen touch or hover action)
Restore defaults
Click to return to the default setting (factory default setting).
Other manuals for LCD MONITOR
2
This manual suits for next models
2
Table of contents
Other Sharp Monitor manuals
Sharp
Sharp PN-V602 User manual
Sharp
Sharp PN-E471R User manual
Sharp
Sharp PN-K321H User manual
Sharp
Sharp PN-525E User manual
Sharp
Sharp PN-L603W User manual
Sharp
Sharp PN-E803 User guide
Sharp
Sharp PN-85TH1 User manual
Sharp
Sharp PN-HW751 User manual
Sharp
Sharp PN-C703D User manual
Sharp
Sharp LC-121M2E User manual
Sharp
Sharp PN-E471 User manual
Sharp
Sharp LL-172G User manual
Sharp
Sharp PN-T321 User guide
Sharp
Sharp PN-L862B User manual
Sharp
Sharp PN-HW651 User guide
Sharp
Sharp PN-L851H User manual
Sharp
Sharp LC-15M4E User manual
Sharp
Sharp LL-T1820-H User manual
Sharp
Sharp LC-20VM2 User manual
Sharp
Sharp PN-L805H User manual
