Sharp B-32C1 User manual
8M-B32C1 Dismantle Instruction
1
Dismantle Instruction
LCD MONITOR
MODEL
8M-B32C1
8M-B32C1 Dismantle Instruction
2
Table of contents
1. Scope.................................................................................................................. 3
2. Tools for dismantling............................................................................................... 3
3. Dismantle Procedure .............................................................................................. 3
4. Stand, Back cover and PWB Plate............................................................................... 4
5. Printed circuit boards ............................................................................................. 8
6. Battery................................................................................................................ 9
7. LCD Module ........................................................................................................ 10
8. Capacitors.......................................................................................................... 11
9. Parts List ........................................................................................................... 12
8M-B32C1 Dismantle Instruction
3
1. Scope
This document describes dismantling instruction according to Annex VII of Directive 2012/19/EU.
2. Tools for dismantling
Below tools are required to dismantle this product.
- Screw Driver
- Nipper
3. Dismantle Procedure
This product can be dismantled by below steps.
1. Remove Stand, Back cover and PWB Plate (section 4)
2. Remove Printed circuit boards (section 5)
3. Remove Battery (section 6)
4. Dismantle LCD (section 7)
5. Remove Electrolyte Capacitors (section 8)
8M-B32C1 Dismantle Instruction
4
4. Stand, Back cover and PWB Plate
Stand can be removed with screw driver.
Remove SCREW COVER SEAL on back cover.
Then back cover can be removed with screw driver.
8M-B32C1 Dismantle Instruction
5
Cut the cable tie on VESA angle with nipper, and peel off ALPET SHEET and ALPET SHEET S.
Then remove VESA angle with screw driver. (right side in back view)
ALPET SHEET S
ALPET SHEET
8M-B32C1 Dismantle Instruction
6
Detach the cables from DC switch PWB and remove the PWB with screw driver.
Remove WIRING SHEET (Black PC sheet) from PWB Plate.
Release all the cables that runs through the plate aperture. (cables from beneath the plate).
DC switch PWB
8M-B32C1 Dismantle Instruction
7
Detach Key-FFC from the connector on Main I/F PWB
Release from wire holders and remove the fixing tape on PWB Plate.
Then PWB Plate can be removed with screw driver.
(When the plate is lifted up, cables should go through the aperture of plate)
8M-B32C1 Dismantle Instruction
8
5. Printed circuit boards
All PWBs can be removed by screw driver.
Power PWB (1pcs)
Main I/F PWB (1pcs)
LED Driver PWB (2pcs) UCCT PWB (1pcs) DC switch PWB (1pcs)
Connector PWB (1pcs) Varistor PWB (1pcs)
T-CON PWB (1pcs) Key PWB (1pcs)
8M-B32C1 Dismantle Instruction
9
6. Battery
This model uses only CR2032 Lithium Coin battery on Main I/F PWB.
Battery CR2032 can easily be removed from the battery holder.
8M-B32C1 Dismantle Instruction
10
7. LCD Module
- LCD Dismantle procedure
LCD
Other manuals for B-32C1
1
Table of contents
Other Sharp Monitor manuals
Sharp
Sharp LL-T17A3 User manual
Sharp
Sharp LL-191A User manual
Sharp
Sharp aquos PN-L603B User guide
Sharp
Sharp PN-E602 User manual
Sharp
Sharp PN-L601B Release note
Sharp
Sharp 70LCDINT Quick start guide
Sharp
Sharp PN-70TA3 User manual
Sharp
Sharp PN-R903 User manual
Sharp
Sharp PN-Q901 User manual
Sharp
Sharp PN-C605B User manual
Sharp
Sharp PN-L803CA Installation manual
Sharp
Sharp PN-G655E User manual
Sharp
Sharp LC-28HM2 User manual
Sharp
Sharp PN-K322B User guide
Sharp
Sharp PN-Y475 User guide
Sharp
Sharp PN-K321 User manual
Sharp
Sharp LL-T15A4 User manual
Sharp
Sharp PN-K321 User manual
Sharp
Sharp IV-08MP User manual
Sharp
Sharp PN-E702 User guide
