Sharp Carousel RK56S27 User manual

For Sharp Carousel®Built-in Kit

Models RK56S27 or RK56S30

S = STAINLESS

THIS KIT IS UL APPROVED TO ALLOW CERTAIN MICROWAVE

OVENS TO BE INSTALLED ABOVE ANY ELECTRIC WALL OVEN.

PLEASE SEE THE OPERATION MANUAL REGARDING APPROVED

BUILT-IN APPLICATIONS.

IMPORTANT:

This Built-in Kit is designed for and approved only for those

Sharp Microwave Ovens specifying Built-In Kit RK56S27 or

RK56S30. Refer to instruction manual for approved models.

PLEASE READ THESE INSTRUCTIONS

THOROUGHLY

BEFORE BEGINNING INSTALLATION!

• Be sure to DISCONNECT THE PLUG of the microwave

oven from the electrical outlet before installing the Built-in

Kit. Remove the Carousel turntable from the oven cavity.

• Because the kit includes metal parts, due caution should

be used in handling and installation to avoid the possibil-

ity of injury.

ITEM PART NAME QTY

AFRONT FRAME

RK56S27: FDECAB252MRK0

RK56S30: FDECAB253MRK0

B BACK FRAME

RK56S27: FDECAB255MRK0

RK56S30: FDECAB255MRK0

C EXHAUST DUCT ASSEMBLY

PDUC-B188MRP0

D SCREW D: XTSS740P20000 2

E SCREW E: XOPS740P16000 4

INSTALLATION INSTRUCTIONS

A B

V-cut

indicates

center of

duct

The opening in the wall or cabinet must be within the

following dimensions:

Cut Out RK56S27 & RK56S30

Height (A) 16

1/4"

Width (B) 261/8" to 26

3/8"

Minimum Depth (C) 20"

Outlet should NOT be in the shaded area as indicated on

Sketch 1.

SKETCH 1

NOTES

• Please allow minimum 3" wood gap between the

microwave oven cutout and the appliance cutout below

the microwave oven. See Sketch 2

3" Min.

Microwave cutout

Wall oven cutout

SKETCH 2

• If the dimension of DEPTH (C) is more than 21", the outlet

location may be any area on the rear wall.

• The oor of the opening should be constructed of plywood

strong enough to support the weight of the oven and oor

load (about 100 pounds). The oor should be level and

90˚ with the face of the cabinet for proper installation and

operation of the oven. Be sure to check the local building

code as it may require that the opening be enclosed with

sides, ceiling and rear partition. The proper functioning of

the oven does not require the enclosure.

STEP 1 CABINET OR WALL OPENING

1. Place the EXHAUST DUCT ASSEMBLY in the center of the

opening. Position the front edge of the duct 3/8" proud of

the front edge of the cabinet. See Sketch 3.

2. Mark the two holes, center punch and pre-drill with 1/16"

drill bit. Secure the EXHAUST DUCT ASSEMBLY with two

SCREWS D. See Sketch 3.

STEP 2 EXHAUST DUCT ASSEMBLY INSTALLATION

3/8”

Screw D

Exhaust duct assembly,

position 3/8" proud of the

front edge of cabinet

SKETCH 3

1. Place the oven adjacent to the wall or cabinet opening.

Plug the POWER CORD into the electrical outlet.

2. Carefully guide the assembled oven into the prepared

opening. Slide the oven on the EXHAUST DUCT

ASSEMBLY. See Sketch 4. Avoid pinching the cord

between the oven and the wall. Adjust the position of

the oven so that the feet of the oven are tted into the

recesses of the EXHAUST DUCT ASSEMBLY and door

will open properly. See Sketch 5.

SKETCH 4

Exhaust

duct

assembly

Foot

Duct recess

SKETCH 5

STEP 3 FRAME INSTALLATION

For any other assistance or information about this kit,

please call Sharp’s Customer Assistance Center at

1-800-BE-SHARP (1-800-237-4277)

SHARP ELECTRONICS CORPORATION

100 Paragon Drive, Montvale, New Jersey 07645 TINSEB567MRR0

STEP 3 FRAME INSTALLATION

3. DISASSEMBLY: The FRONT FRAME and BACK FRAME

come pre-assembled with ball studs engaged in the

receivers. Separate the FRONT FRAME from the BACK

FRAME. Place the assembly face down on a protected

surface. At the location of the ball stud, insert a at head

screwdriver between the FRONT FRAME and the BACK

FRAME and gently pry up to disengage the ball stud from

the receiver. Repeat for each corner. See Sketch 6.

SKETCH 6

4. BACK FRAME INSTALLATION: Position back frame equal

space top to bottom, side to side. Mark for 4 holes, center

punch and pre-drill with 1/16" drill bit. Secure frame with

4 SCREWS (E). See Sketch 7.

Equal gap top, bottom

Equal gap

side to side

Mounting holes

Screw E

SKETCH 7

5. FRONT FRAME INSTALLATION: Place the FRONT

FRAME onto the BACK FRAME and align ball studs

and receivers. Secure the FRONT FRAME to the BACK

FRAME by rmly pushing the front frame onto the back

frame engaging the four (4) snap attachments. See

Sketch 8.

Snap

Attachment

SKETCH 8

This manual suits for next models

Other Sharp Microwave Oven manuals

Popular Microwave Oven manuals by other brands

Daewoo

Daewoo KOG-574R0S Service manual

LG MH7040SS instruction manual

Dometic

Dometic DOTRM13W installation instructions

Sanyo

Sanyo EM-X680 instruction manual

KitchenAid

KitchenAid KMCX4510 Use and care

Smeg

Smeg S45MCX1 Instructions for use

Russell Hobbs

Russell Hobbs RHM2044 user guide

Sunbeam

Sunbeam SMW759 owner's manual

Gallet

Gallet FMOE230S instruction manual

Bosch

Bosch CEG732X.1B User manual and installation instructions

Dometic

Dometic Roadmate 230 operating manual

Samsung

Samsung SJ0396W Owner's instructions

Sanyo

Sanyo EM-P494WS Supplement of service manual

Electrolux

Electrolux EMS2840 user manual

Daewoo

Daewoo KOC-984T2S13 Service manual

Impecca

Impecca CM07M2 user manual

Sanyo

Sanyo EM-G5596V UK2 instruction manual

Samsung

Samsung CE2927 Service manual