Sharp EL-2607R User manual

ELECTRONIC PRINTING CALCULATOR

DRUCKENDER TISCHRECHNER

CALCULATRICE IMPRIMANTE ÉLECTRONIQUE

SZALAGOS ASZTALI KALKULÁTOR

OPERATION MANUAL

BEDIENUNGSANLEITUNG

MODE D’EMPLOI

HASZNÁLATI ÚTMUTATÓ

EL-2607R

ENGLISH ............................................... Page 2

CALCULATION EXAMPLES ............. Page 34

DEUTSCH .............................................. Seite 10

RECHNUNGSBEISPIELE ................ Seite 34

FRANÇAIS ............................................. Page 18

EXEMPLES DE CALCULS ............... Page 35

MAGYAR ................................................ Oldal 26

SZÁMÍTÁSI PÉLDÁK ........................ Oldal 35

Caution!

The socket outlet shall be installed near the equipment and shall be easily accessible.

Vorsicht!

Die Netzsteckdose muß in der Nähe des Gerätes angebracht und leicht zugänglich

sein.

Observera!

Anslut till ett vägguttag som återfinns nära enheten och är lätt åtkomligt.

Let op!

Het stopcontact moet in de buurt van het apparaat zijn en ook gemakkelijk

toegankelijk zijn.

Atenção!

A tomada elétrica deve estar perto do equipamento e ser de fácil acesso.

Attention!

La prise de courant murale doit être installée à proximité de l’appareil et doit être

facilement accessible.

Aviso!

El tomacorriente debe estar instalado cerca del equipo y debe quedar bien accesible.

Attenzione!

La presa della corrente deve essere installata in prossimità dell’apparecchio ed

essere facilmente accessibile.

Huomautus!

Pistorasia tulee asentaa laitteen lähelle paikkaan, jossa sen käyttöä on helppoa.

Figyelem!

A kalkulátort úgy érdemes elhelyezni, hogy a hálózati csatlakozó aljzatot könnyen

el lehessen érni.

– 1 –

THE KEYBOARD DIE TASTATUR LE CLAVIER A BILLENTYŰZET

P P IC K A F 6 3 2 1 0

789

123

000

•

P PIC K A F63210

1716

– 2 –

Thank you for your purchase of the SHARP electronic calculator, model EL-2607R. Your

SHARP calculator is specially designed to save work and increase efficiency in all business

applications and general office calculations. Careful reading of this manual will enable

you to use your new SHARP calculator to its fullest capability.

To insure trouble-free operation of your SHARP calculator, we recommend the following:

1. The calculator should be kept in areas free from extreme temperature changes,

moisture, and dust.

2. A soft, dry cloth should be used to clean the calculator. Do not use solvents or a wet

cloth.

3. If you are not going to use the calculator for a time period, please pull out the power

cord to cut electricity completely.

4. If service should be required, use only a SHARP servicing dealer, a SHARP approved

service facility or SHARP repair service.

5. Do not wind the AC cord around the body or otherwise forcibly bend or twist it.

6. Since this product is not waterproof, do not use it or store it where fluids, for example

water, can splash onto it. Raindrops, water spray, juice, coffee, steam, perspiration,

etc. will also cause malfunction.

SHARP will not be liable nor responsible for any incidental or consequential economic

or property damage caused by misuse and/or malfunctions of this product and its

peripherals, unless such liability is acknowledged by law.

WARNING

THE VOLTAGE USED MUST BE THE SAME AS SPECIFIED ON THIS CALCULATOR.

USING THIS CALCULATOR WITH A HIGHER VOLTAGE THAN THAT WHICH IS

SPECIFIED IS DANGEROUS AND MAY RESULT IN A FIRE OR OTHER TYPE OF

ACCIDENT CAUSING DAMAGE. WE ARE NOT RESPONSIBLE FOR ANY DAMAGE

RESULTING FROM USE OF THIS CALCULATOR WITH A VOLTAGE OTHER THAN

THAT WHICH IS SPECIFIED.

ENGLISH

INTRODUCTION

OPERATIONAL NOTES

– 3 –

POWER SWITCH

PRINT/ITEM COUNT MODE SELECTOR:

“P” (Print mode): The calculator functions as a print/display calculator.

“•” (Neutral): The calculator functions as a display calculator. (Non-

print mode)

“P•IC”: The calculator functions as a print/display calculator with an item

counter.

The counter will count the number of times that

has been

pressed in addition.

Note: •Each time is used in subtraction, 1 will be subtracted from the

count.

•The count is printed when the calculated result is obtained.

•Pressing of

＊

, or clears the counter.

•The counter has the capacity of a maximum of 3 digits (up to ±999).

If the count exceeds the maximum, the counter will recount from

zero.

CONSTANT/ADD MODE SELECTOR:

“K” : The following constant functions will be performed:

Multiplication: The calculator will automatically remember the first number

entered (the multiplicand) and instruction.

Division: The calculator will automatically remember the second

number entered (the divisor) and instruction.

“•” : Neutral

“A” : Use of the Add mode permits addition and subtraction of numbers

without an entry of the decimal point. When the Add mode is activated,

OPERATING CONTROLS

CONTENTS

Page

•OPERATING CONTROLS ........................................................................................3

•INK ROLLER REPLACEMENT ................................................................................7

•PAPER ROLL REPLACEMENT ................................................................................8

•ERRORS ..................................................................................................................9

•SPECIFICATIONS .................................................................................................... 9

•CALCULATION EXAMPLES ................................................................................... 34

– 4 –

the decimal point is automatically positioned according to the decimal

selector setting.

Use of , , and will automatically override the Add mode

and decimally correct answers will be printed at the preset decimal

position.

ROUNDING SELECTOR:

“” : An answer is rounded up.

“5/4” : An answer is rounded off.

“” : An answer is rounded down.

Example: Set Decimal Selector to 2.

4 ⴓ9 = 0.444 ... , 5 ⴓ9 = 0.555 ...

4 9

5 9

0.45 0.56

5/4 0.44 0.56

0.44 0.55

Note: The decimal point floats during successive calculation by the use of

or .

If the decimal selector is set to “F” then the answer is always rounded

down ( ).

DECIMAL SELECTOR:

Presets the number of decimal places in the answer.

In the “F” position, the answer is displayed in the floating decimal system.

GRAND TOTAL MODE SELECTOR:

“GT”: This selector will accumulate the following:

(“✱+” will be printed.)

1. Addition and subtraction totals obtained with

＊

2. Product and quotient totals obtained with

or .

3. Answers obtained with or .

“•”: Neutral, GT OFF

PAPER FEED KEY

LAST DIGIT CORRECTION KEY:

Operation of this key in entered numbers or calculated results shifts the

number one digit to the right together with the decimal point. Used for one

digit correction.

– 5 –

GRAND TOTAL KEY:

Prints and clears the “GT” memory contents.

NON-ADD/SUBTOTAL KEY:

Non-add – When this key is pressed right after an entry of a number in

the Print mode, the entry is printed on the left-hand side with

“#”.

This key is used to print out numbers not subjects to calculation

such as code, date, etc.

Subtotal – Used to get subtotal(s) of additions and/or subtractions. When

pressed following

or , the subtotal is printed with “ ◊”

and the calculation may be continued.

By pressing this key even in the Non-print mode, the displayed number

is printed with “P”.

＊

CLEAR ENTRY/CLEAR AND TOTAL KEY:

Clear entry –When pressed after a number and before a function,

clear the number.

Clear and total –When pressed after a function key, prints the total of

addition and subtraction with “ ✱”. This key also serves

as a clear key for the calculation register and resets an

error condition. The contents of the memory are not

affected by use of

＊

MEMORY PLUS KEY

MEMORY MINUS KEY

RECALL MEMORY KEY

RECALL AND CLEAR MEMORY KEY

CHANGE SIGN KEY:

Changes the algebraic sign of a number (i.e., positive to negative or negative

to positive).

MARKUP KEY:

Used to perform mark-ups, percent change and automatic add-on/discount.

– 6 –

DISPLAY

Display format:

Symbols:

M : Memory symbol

Appears when a number is in memory.

–: Minus symbol

Appears when a number is a negative.

E : Error symbol

Appears when an overflow or other error is detected.

•: Grand total memory symbol

Appears when a number is in the grand total memory.

– 7 –

If printing is blurry even when the ink roller is in the proper position, replace the roller.

Ink roller: Type EA-741R

WARNING

APPLYING INK TO WORN INK ROLLER OR USE OF UNAPPROVED INK ROLLER

MAY CAUSE SERIOUS DAMAGE TO PRINTER.

1. Set the power switch to the OFF.

2. Remove the printer cover by sliding it. (Fig. 1)

3. Move the knob of the ink roller slightly towards you and then lift it up (in the direction

of the arrow). Take care not to catch the ink roller under the case. (Fig. 2)

4. Install the new ink roller and push the knob of the ink roller. Make sure that the ink

roller is securely in place. (Fig. 3)

5. Put back the printer cover.

Note: When you clean the printer cover, remove the printer cover by sliding it. (Fig. 1)

Then clean the printer cover by using a soft, dry cloth. Do not use solvents or a

wet cloth.

Cleaning the printing mechanism

If the print becomes dull after long time usage, clean the printing wheel according

to the following procedures:

1) Install the paper roll and feed it until it comes out of the front of the print mechanism.

2) Remove the printer cover and the ink roller.

3) Put a small brush (like a tooth brush) lightly to the printing wheel and clean it by

pressing .

4) Put back the ink roller and the printer cover.

INK ROLLER REPLACEMENT

Fig. 2

Fig. 1 Fig. 3

Knob of the

ink roller

– 8 –

Paper roll

Paper holder

Fig. 4

Fig. 3

Paper cutter

Paper feed key

PAPER ROLL REPLACEMENT

Paper holder

Fig. 1 Fig. 2

DO NOT PULL PAPER BACKWARDS AS THIS MAY CAUSE DAMAGE TO PRINTER

MECHANISM.

1. Assemble the paper holder. (Fig. 1)

2. Insert the leading edge of the paper into the opening directly behind the print

mechanism. (Fig. 2)

3. Press the paper feed key and feed the paper under the edge of the paper cutter.

(Fig. 3)

4. Place the paper roll in the paper holder at the back of the calculator. (Fig. 4)

Other manuals for EL-2607R

Table of contents

Other Sharp Calculator manuals

Sharp

Sharp el-9950 User manual

Sharp

Sharp EL1192BL - Desktop 2 Color Printing... User manual

Sharp

Sharp EL-1750V User manual

Sharp

Sharp EL1750PIII - Printing Calculator,... User manual

Sharp

Sharp ELSI MATE EL-340W User manual

Sharp

Sharp EL-2125C User manual

Sharp

Sharp EL-M335 User manual

Sharp

Sharp EL-1607P User manual

Sharp

Sharp EL-2901RH User manual

Sharp

Sharp ELSIMATE EL-332A User manual

Sharp

Sharp ELW535B - WriteView Scientific Calculator User manual

Sharp

Sharp WriteView EL-W535XG Installation manual

Sharp

Sharp EL-2910R User manual

Sharp

Sharp ELSI MATE EL-320W User manual

Sharp

Sharp EL-W516B - Scientific Calculator With... User manual

Sharp

Sharp Elsi Mate EL-R297 User manual

Sharp

Sharp ELSIMATE EL-339H User manual

Sharp

Sharp EL-W516T User manual

Sharp

Sharp EL-334M User manual

Sharp

Sharp EL-T100WB User manual

Sharp

Sharp EL-506V Installation manual

Sharp

Sharp EL-2615PIII User manual

Sharp

Sharp ELSI MATE EL-330A User manual

Sharp

Sharp Elsimate EL-337C User manual

Popular Calculator manuals by other brands

HP 35s Instruction guide

Casio

Casio CFX-9970G user guide

LEXIBOOK

LEXIBOOK EL350 instruction manual

HP HP-97 Service manual

Citizen

Citizen SDC-414N instruction manual

Casio

Casio fx-3800P Operation manual

Canon

Canon P26-DHIII instructions

Citizen

Citizen 520DPA instruction manual

Casio

Casio FX-9860GII - SOFTWARE VERSION 2-00 quick start guide

Casio

Casio MS-7UC user guide

Casio

Casio FC-200 owner's manual

Casio

Casio fx-CG50 instructions

HP HP-67 Owner's handbook

Royal

Royal CBC2000 instruction manual

Heathkit

Heathkit IC-2009 Assembly manual

Universal

Universal UNV-15907 owner's manual

Casio

Casio ALGEBRA FX 2.0 user guide

Casio

Casio CLASSPad300 - ClassPad 300 Touch-Screen Graphing Scientific... user guide