Sercomm SW-BSW01N User manual

1 SW-ESW01N QIG V0.5

SW-ESW01N, SW-BSW01N Z-Wave Binary Switch Installation Guide

SW-ESW01N is a powered Z-Wave Plus electrical power measuring device, which is compatible with Z-Wave Plus enabled

devices, regardless of the manufacturer and can also be used with other devices with the Z-Wave logo. If device is not part of

Z-Wave network, with auto network add, the device will activate add process as soon as the device is powered on. The user can

also manually activate add process by pressing the On/Off button. Once it is included into a Z-Wave network, SW-ESW01N can

also act as a repeater in the network.

With a Z-Wave controller, user can also control the energy switch remotely. The energy switch has built-in over voltage, over

current protection and OTA feature.

Specification

Frequency 908-916 MHz

Operating Temperature Temperature: 0° - 40°C (32° - 104°F); Humidity: 0% - 80% RH (non-condensing)

Storage Temperature Temperature: -20° - 70°C (-4° - 158°F); Humidity: 0% - 90% RH (non-condensing)

RF Communication Range Open Air: 80M (Max.)

LED Indicator LED x1

Power 120VAC

Operating Voltage 120V / 60Hz

Max Load 15A Resistive / 400W Incandescent

Over Voltage Protection(OVP) 132V (126V resume)

Over Current protection(OCP) 15.5A

Dimensions (H x W x D) 55mm x 55mm x 37.5mm

Compliance FCC, UL ,Z-Wave plus

Package Contents

Warnings and Cautions

To be installed and/or used in accordance with appropriate electrical codes and regulations.

If you are unsure about any part of these instructions, please consult a qualified electrician.

To reduce the risk of overheating, do not install near heat sources, such as fires, boilers or heating vents.

Do not locate the device facing direct sunlight or humid place.

SW-ESW01N

Z-Wave Binary Switch

SW-ESW01N QIG V0.5

Save this instruction sheet. It contains important technical data, which will be useful for future reference.

Operation

1. On/Off and Pairing Button 2. On/Off , Pairing and alarm LED (Green)

Installation

1. Put the SW-ESW01N into a wall receptacle. Make sure the receptacle is working properly. If it is controlled by a wall switch,

make sure it is set to ON all the times.

2. Attach the appliance to the SW-ESW01N and make sure the load does not exceed 15A

Device Functions

The table below summarizes Z-Wave related functions supported by the energy switch.

Function Description

Add(Inclusion)

1. Put the Z-Wave controller into "Add (Inclusion)" mode.

2. Power on the device.

3. The LED is blinking while scanning the network and. This process may

take up to 30 seconds. (In the meanwhile, our device will send its NIF.)

4. If the add process is successful, the LED will turn off and restore to relay state.

If the process failed, press the On/Off button once and the device will be in auto add

mode again.

Remove(Exclusion)

1. Set the Z-Wave controller to "Remove (Exclusion)" mode.

2. Press the On/Off button three times within two seconds.

3. The LED will be blinking for one second.(In the meanwhile, our device will send its

NIF.)

Note 1: if the Remove process is successful, the node ID will be cleared and the device

will be in auto add mode.

Note 2:Relay state default off

Reset to Factory Defaults

1. Press the On/Off button 4 times within two seconds and hold the 4th press until the

LED lights up.

2. The LED will turn off after three seconds. The node ID will be cleared and all

settings will be reset to factory defaults.

3. The device will be in auto add mode.

Note :Relay state default off

Meter

The device support below metering scale.

-0x00 Accumulate power consumption (kWh)

-0x02 Power consumption (W)

-0x04 AC load voltage (V)

-0x05 AC load current (A)

-0x06 Load power factor (PF)

*LED will be blinking quickly every 0.1sec, if OCP(Over Current Protection) or OVP(Over Voltage Protection) kick in.

Otherwise, the blinking speed will be normal every 0.5sec.

SW-ESW01N QIG V0.5

Z-Wave Command Classes

COMMAND_CLASS_BASIC_V1

COMMAND_CLASS_VERSION_V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

COMMAND_CLASS_CONFIGURATION_V1

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1

COMMAND_CLASS_POWERLEVEL_V1

COMMAND_CLASS_ASSOCIATION_V2

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1

COMMAND_CLASS_SWITCH_BINARY_V1

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2

COMMAND_CLASS_METER_V3

COMMAND_CLASS_NOTIFICATION_V4

Association

Support grouping identifier = 1

Support one group with 1 nodes.

All triggering report will be sent to the associated nodes.

Notification

Event type:

OCP:0x06

OVP:0x07

Notification type:

Power management:0x08

Devices From Multiple Vendors In One Network

SW-ESW01N can be included and operated in any Z-Wave network with other Z-Wave certified devices

from other manufacturers and/or other applications. All non-battery operated nodes within the network will

act as repeaters regardless of vendor to increase reliability of the network.

Z-Wave Configuration

Configuration

Parameter Function Size

(Byte) Configuration

Value Default

Setting Description

1 Relay state when power up 1 0~2 0 0 : Last relay state

1 : Relay on

2 : Relay off

2 Auto report relay state 1 0~1 1 0 : Disable

1 : Enable

SW-ESW01N QIG V0.5

Command Class Report

Command Class Report Type Status Description

Switch Binary Relay State Relay on: FF

Relay off: 00 When relay state changes or device

powers up.

Meter OVP, OCP triggered

Scale: Depend on scale type.

Value: Depend on metering result. When OCP or OVP kick in, the

device will send meter report and

alarm report sequentially.

Alarm OVP, OCP triggered

Alarm Type: 08 (Power Management)

Alarm Level: FF (Open), 00 (Close)

SW-ESW01N QIG V0.5

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

Caution!

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to

operate the equipment.

SW-ESW01N QIG V0.5

Canada Statement

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage;

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

This manual suits for next models

Table of contents

Other Sercomm Switch manuals

Sercomm

Sercomm SW-ESW01N User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual