Sengled ZM005 User manual
ZM005 User Manual
1. Introduction
ZM005 is a cost-effective embedded ZIGBEE Low Energy module launched by
sengled, CustomNodes QPG6095ZDTR13 technology, which are fully integrated
System-on-Chips that integrate a 2.4 GHz, IEEE 802.15.4-2003-compliant
transceiver, 32-bit ARM @ Cortex @ - M4 core, maximum working frequency of
64 MHzThe highest 512 kB flash and 64 kB of RAM12 channel peripherals
reflection system, may realize the MCU peripheral autonomic interaction
Integrated PA, TX power up to 10 dBm (2.4 GHz) powerful peripherals, QFN40
6x6 mm package.
2. Module samples
3. General information
1. At 2.4 GHz (250 KBPS O-QPSK DSSS), the Rx current is 3 mA
2. A combination of 64 MHz ARM Cortex-M4 and a high-performance 2.4 GHz radio
is designed for IoT connectivity Provide industry-leading energy-saving wireless SoC
3.Built-in 64kBytes SRAM, 512KBytes Flash
4.Single power supply 1.8 to 3.6V
5. supported with 10dBm maximum TX power
6.10 golden-finger pins are easy installation with PCB-Through-PCB
7.Compact size 24*17
8.PCB antenna
9.Sengled Zigbee Module
FCC Certification Requirements.
According to the definition of mobile and fixed device is described in Part 2.1091(b), this
device is a mobile device.
And the following conditions must be met:
1. This Modular Approval is limited to OEM installation for mobile and fixed applications
only. The antenna installation and operating configurations of this transmitter, including
any applicable source-based time- averaging duty factor, antenna gain and cable loss
must satisfy MPE categorical Exclusion Requirements of 2.1091.
2. The EUT is a mobile device; maintain at least a 20 cm separation between the EUT and
the user’s body and must not transmit simultaneously with any other antenna or
transmitter.
3. A label with the following statements must be attached to the host end product: This
device contains FCC ID: 2AGN8-ZM005.
4.This module must not transmit simultaneously with any other antenna or
transmitter.
5.The module is limited to OEM installation ONLY.
6.The OEM integrator is responsible for ensuring that the end-user has no
manual instructions to remove or install module.
7. The host end product must include a user manual that clearly defines operating
requirements and conditions that must be observed to ensure compliance with current
FCC RF exposure guidelines.
For portable devices, in addition to the conditions 3 through 6 described above, a
separate approval is required to satisfy the SAR requirements of FCC Part 2.1093
If the device is used for other equipment that separate approval is required for all other
operating configurations, including portable configurations with respect to 2.1093 and
different antenna configurations.
For this device, OEM integrators must be provided with labeling instructions of finished
products. Please refer to KDB784748 D01 v07, section 8. Page 6/7 last two
paragraphs:
A certified modular has the option to use a permanently affixed label, or an electronic
label. For a permanently affixed label, the module must be labeled with an FCC ID -
Section 2.926 (see 2.2 Certification (labeling requirements) above). The OEM manual
must provide clear instructions explaining to the OEM the labeling requirements,
options and OEM user manual instructions that are required (see next paragraph).
For a host using a certified modular with a standard fixed label, if (1) the module’s FCC
ID is not visible when installed in the host, or (2) if the host is marketed so that end
users do not have straightforward commonly used methods for access to remove the
module so that the FCC ID of the module is visible; then an additional permanent label
referring to the enclosed module:“Contains Transmitter Module FCC ID:
2AGN8-ZM005” or “Contains FCC ID: 2AGN8-ZM005” must be used. The host OEM
user manual must also contain clear instructions on how end users can find and/or
access the module and the FCC ID.
The final host / module combination may also need to be evaluated against the FCC
Part 15B criteria for unintentional radiators in order to be properly authorized for
operation as a Part 15 digital device.
The user’s manual or instruction manual for an intentional or unintentional radiator shall
caution the user that changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment. In
cases where the manual is provided only in a form other than paper, such as on a
computer disk or over the Internet, the information required by this section may be
included in the manual in that alternative form, provided the user can reasonably be
expected to have the capability to access information in that form.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
To ensure compliance with all non-transmitter functions the host manufacturer is
responsible for ensuring compliance with the module(s) installed and fully operational. For
example, if a host was previously authorized as an unintentional radiator under the
Declaration of Conformity procedure without a transmitter certified module and a module
is added, the host manufacturer is responsible for ensuring that the after the module is
installed and operational the host continues to be compliant with the Part 15B
unintentional radiator requirements.
Canada Regulations:
This device complies with Industry Canada’s licence-exempt RSSs. Operation
is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présentappareilestconforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitationestautorisée aux deux
conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareildoit accepter tout brouillageradioélectriquesubi,
mêmesi le brouillageest susceptible d’encompromettre le fonctionnement.
Caution：
IC statement
The host product shall be properly labelled to identify the modules within the host
product.
The Innovation, Science and Economic Development Canada certification label of
a module shall be clearly visible at all times when installed in the host product;
otherwise, the host product must be labelled to display the Innovation, Science
and Economic Development Canada certification number for the module,
preceded by the word “Contains” or similar wording expressing the same meaning,
as follows:
“Contains IC: 20888-ZM005” or “where: 20888-ZM005 is the module’s certification
number”.
Le produit hôte doit être correctement étiqueté pour identifier les modules dans le produit
hôte.
L'étiquette de certification d'Innovation, Sciences et Développement économique Canada
d'un module doit être clairement visible en tout temps lorsqu'il est installé dans le produit
hôte; sinon, le produit hôte doit porter une étiquette indiquant le numéro de certification
d'Innovation, Sciences et Développement économique Canada pour le module, précédé
du mot «Contient» ou d'un libellé semblable exprimant la même signification, comme suit:
"Contient IC: 20888-ZM005" ou "où: 20888-ZM005 est le numéro de certification du
module".
A label with the following statements must be attached to the host end product: This
device contains IC: 20888-ZM005.
Table of contents
Other Sengled Lighting Equipment manuals
Sengled
Sengled Snap Crystal N1E-EE6 User manual
Sengled
Sengled smartsense 0058693001 User manual
Sengled
Sengled W1G-N83W3 User manual
Sengled
Sengled element Z01-hub User manual
Sengled
Sengled 0059693040 User manual
Sengled
Sengled Smart User manual
Sengled
Sengled W1G-N84 User manual
Sengled
Sengled Soft White A19 Bulbs User manual
Sengled
Sengled B11-U21W User manual
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
