SELT V ZIIIP User manual

TECHNICAL AND OPERATIONAL DOCUMENTATION

INSTALLATION MANUAL,

OPERATING MANUAL AND INSTRUCTIONS FOR SAFE USE

(Translated from the original manual)

5. Steel and aluminium components and structural sets

5.7. Veranda V ZIIIP / Pergola V ZIIIP

5.7

DT-E

Translated from the original manual

DT-E 5.7: SYSTEM VERANDA V ZIIIP –SYSTEM PERGOLA V ZIIIP

Edition 3 / March 2021 / EN page 2 / 40

PRODUCT NAME:

VERANDA V ZIIIP

PERGOLA V ZIIIP

MARKING OF PRODUCT MANUFACTURER:

Manufacturer name:

SELT Sp. z o. o.

Manufacturer’s registered office:

45- 449 Opole, ul. Wschodnia 23A

Contact details:

Tel: +48 77 553 21 00 (secretariat)

Fax: +48 77 553 22 00

Website:

www.selt.com

E-mail:

[email protected]

PRODUCT SAFETY MARKING:

The product meets the CE safety requirements.

THIS TECHNICAL AND OPERATIONAL DOCUMENTATION:

Is valid from: 01 March 2021

Is applicable to the above listed product versions.

Translated from the original manual

DT-E 5.7: SYSTEM VERANDA V ZIIIP –SYSTEM PERGOLA V ZIIIP

Edition 3 / March 2021 / EN page 3 / 40

TABLE OF CONTENTS

1INTRODUCTION............................................................................................................................................................ 4

1.1 SAFETY GUIDELINES FOR THE PRODUCT................................................................................................................. 4

1.2 EXPLANATION OF SYMBOLS AND SIGNS ................................................................................................................. 4

1.3 TERMS AND DEFINITIONS ....................................................................................................................................... 5

1.4 SUBJECT, INTENDED USE AND CONTENTS OF THE DOCUMENTATION................................................................... 6

2PRODUCT TECHNICAL INFORMATION.......................................................................................................................... 7

2.1 TECHNICAL PARAMETERS: ...................................................................................................................................... 7

2.2 PRODUCT SPECIFICATION ..................................................................................................................................... 10

3TRANSPORT AND STORAGE OF THE PRODUCT.......................................................................................................... 11

3.1 COMPLETENESS AND QUALITY CONDITION OF THE DELIVERY ............................................................................. 11

3.2 GENERAL CONDITIONS FOR TRANSPORT AND STORAGE OF THE PRODUCT ........................................................ 11

3.3 OBLIGATORY DESCRIPTIONS TO BE PLACED ON THE PRODUCT PACKAGING ....................................................... 11

4PRODUCT INSTALLATION........................................................................................................................................... 12

4.1 GENERAL REQUIREMENTS FOR SAFE INSTALLATION ............................................................................................ 12

4.2 REQUIREMENTS FOR SAFE INSTALLATION OF THE PRODUCT AT HEIGHTS........................................................... 12

4.3 PREPARATION FOR INSTALLATION........................................................................................................................ 13

4.4 GENERAL GUIDELINES FOR PRODUCT INSTALLATION........................................................................................... 13

4.5 INSTALLATION TOOLS ........................................................................................................................................... 13

4.6 INSTALLATION....................................................................................................................................................... 13

4.6.1 BRACKETS –DIMENSIONS ................................................................................................................................ 14

4.6.2 INSTALLATION –VERSION WITH BRACKETS ..................................................................................................... 16

4.6.3 INSTALLATION - WALL VERSION (WITH FRONT POSTS)................................................................................... 23

4.7 ELECTRIC DRIVE..................................................................................................................................................... 30

4.7.1 CONNECTION TO ELECTRICAL INSTALLATION .................................................................................................. 30

4.7.2 START-UP AND ADJUSTMENT .......................................................................................................................... 30

5SYSTEM OPERATION AND PRODUCT SAFETY............................................................................................................. 31

5.1 GENERAL REQUIREMENTS FOR OCCUPATIONAL HEALTH AND SAFETY ................................................................ 31

5.2 SAFETY REQUIREMENTS RELATED TO SPECIAL CONDITIONS AND PLACES OF PRODUCT USE.............................. 31

5.3 OPERATIONAL SAFETY........................................................................................................................................... 31

5.4 MISUSE OF THE SYSTEM........................................................................................................................................ 32

6SYSTEM USE AND MAINTENANCE.............................................................................................................................. 33

6.1 USING THE PRODUCT IN ACCORDANCE WITH ITS INTENDED USE........................................................................ 33

6.2 INSTRUCTION FOR NON-PROFESSIONALS............................................................................................................. 34

6.3 TECHNICAL INSPECTIONS AND REPAIRS................................................................................................................ 34

6.3.1 BASIC ACTIVITIES PERFORMED DURING THE PERIODIC INSPECTION............................................................... 34

6.3.2 NOTES ON CURRENT MAINTENANCE............................................................................................................... 34

6.4 MAINTENANCE...................................................................................................................................................... 35

6.5 GENERAL PRODUCT INFORMATION...................................................................................................................... 36

7GENERAL WARRANTY CONDITIONS........................................................................................................................... 36

7.1 WARRANTY EXCLUSIONS ...................................................................................................................................... 36

8COMPLAINT / TECHNICAL DEFECTS ........................................................................................................................... 38

8.1 COMPLAINTS......................................................................................................................................................... 38

8.2 TECHNICAL DEFECTS ............................................................................................................................................. 38

9PRODUCT DISASSEMBLY / UTILISATION / DISPOSAL.................................................................................................. 38

10 MARKING AND LABELLING THE PRODUCT WITH THE CE MARK ................................................................................ 39

10.1 PRODUCT COMPLIANCE WITH THE CE STANDARD ............................................................................................... 39

10.2 INFORMATION ACCOMPANYING THE CE MARKING ............................................................................................. 39

Translated from the original manual

DT-E 5.7: SYSTEM VERANDA V ZIIIP –SYSTEM PERGOLA V ZIIIP

Edition 3 / March 2021 / EN page 4 / 40

1INTRODUCTION

1.1 SAFETY GUIDELINES FOR THE PRODUCT

The product has been manufactured in accordance with the latest technical knowledge in the field of construction and

manufacturing and meets the safety requirements in accordance with the following standards.

No.

Subject

European Legal Basis

Polish Legal Basis

External blinds and awnings.

Performance requirements

including safety

EN 13561:2015

PN-EN 13561:2015

Construction Products

Regulation (CPR)

Regulation No 305/2011 of the

European Parliament and of the

Council

Act of April 16, 2001 on building products

(Journal of Laws of 2020, item 215) as

amended

Essential requirements for the

machinery

Directive 2006/42/EC of the

European Parliament and of the

Council

Regulation of the Minister of Economy of

October 21, 2008 on the essential

requirements for machines (Journal of

Laws 2008 No. 199, item 1228) as

amended (Dz.U. Journal of Laws

2011.124)

Related documents: Declaration of Performance (external products), Declaration of Conformity and instructions for

installation, use of motors and control.

1.2 EXPLANATION OF SYMBOLS AND SIGNS

The following symbols (pictograms) indicate particularly important threats and safety information.

Pictogram

Pictogram meaning

Information

INFORMATION

Prior to using the product, its operating manual should be read.

Following the operating manual guarantees:

- failure-free use of the product,

- warranty coverage against product defects.

Keep the operating manual for safety of people.

INFORMATION

No harmful or dangerous consequences for people or facilities.

NOTE!

A situation likely to cause product damage or other damage.

No threat for people.

WARNING!

Threat of danger.

DANGER!

This symbol marks all safety information which, if not observed, could

endanger the life or health of persons. Health or life hazard. Risk: danger of

serious injury or death. Unsafe operation that may cause injury or damage to

the product.

WARNING!

Threat to human life or health due to electric shock.

ENVIRONMENT

Marking of electronic or electric equipment, which should be collected in the

designated points.

Translated from the original manual

DT-E 5.7: SYSTEM VERANDA V ZIIIP –SYSTEM PERGOLA V ZIIIP

Edition 3 / March 2021 / EN page 5 / 40

1.3 TERMS AND DEFINITIONS

For the purposes of this documentation the following terms and definitions shall apply:

Product: PERGOLA V ZIIIP

Product made of fabric/material, placed outside; above, in front of or within an opening in a building, or anywhere within

the outer surface of a building; extending in a horizontal and/or inclined and/or vertical plane, pulled in by rolling up the

fabric fixed to the front beam that is mounted with the side guiding beams (side guides). The possible movement of the

fabric - up - down (rolling up - unfolding) is carried out with the use of an electric drive. The product may have front

supports for guiding beams or mounting brackets. The structure of the product is offered in a standard colour from the RAL

palette after confirmation of their availability by the manufacturer. The product serves the function of a sun shading

system.

Fabric:

A part of the product made of fabric or other material that is set in motion by means of a control mechanism, ensuring that

the product fulfills its function. It acts as a sun shield.

Front supports:

A part of the product that serves as a support for the beams guiding the fabric (side guides).

Mounting brackets:

A part of the product that serves as a support for the side beams guiding the fabric, ensuring that the product fulfills its

function.

Guiding beams (side guides):

A part of the product connected to the cassette, acting as a fabric guide and including a fabric tensioning mechanism and

constituting a suspension for the beams supporting the fabric.

Cassette:

Oval-shaped part of the product, fixed to the ground or wall with brackets, or supported only on guiding beams (in the

version with mounting brackets).

PRODUCT VERSIONS:

Veranda V ZIIIP single-module with mounting brackets –a sun protection system consisting of a cassette and two side

guides connected to it together with the fabric, supported on a load-bearing surface by means of mounting brackets

supporting the side guides and cassette mounting brackets, constituting one separate product.

Veranda V ZIIIP multi-module with mounting brackets –a sun protection system consisting of a structure of two or more

single-module veranda awnings joined together, supported on a load-bearing surface by means of common mounting

brackets supporting the side guides and independent cassette mounting brackets, consitutitng one joint product.

Pergola V ZIIIP single-module with front supports (TA - terrace awning) –a sun protection system consisting of a wall-

mounted structure including cassette and two side guides connected to it together with the fabric, supported on the load-

bearing surface only by the cassette mounting brackets and two front supports, constituting one separate product.

Pergola V ZIIIP multi-module with front supports (TA - terrace awning) –a sun protection system consisting of a wall-

mounted structure consisting of two or more single-module Pergolas V connected to each other, supported on the load-

bearing ground only by the cassette mounting brackets and common front supports.

Translated from the original manual

DT-E 5.7: SYSTEM VERANDA V ZIIIP –SYSTEM PERGOLA V ZIIIP

Edition 3 / March 2021 / EN page 6 / 40

1.4 SUBJECT, INTENDED USE AND CONTENTS OF THE DOCUMENTATION

This documentation covers the products manufactured by SELT Sp. z o.o.

This documentation applies to all types of PERGOLA V ZIIIP.

User’s manual and instructions for safe use, with motor manual, should be handed over to the end

user

IMPORTANT INSTRUCTION RELATED TO SAFETY

WARNING - IT IS VERY IMPORTANT TO PROCEED ACCORDING TO THIS MANUAL

TO ENSURE PEOPLE SAFETY.

KEEP THIS MANUAL

The documentation is valid together with the product-specific information available on the website

www.selt.com

This documentation contains:

important guidelines for installation, use and maintenance of the product,

important recommendations for storage and transport,

guidelines, which observance would ensure long-lasting and failure-free operation of the product.

SELT Sp. z o.o. shall not be responsible for damages resulting from non-observance of the recommendations included in

this documentation.

For further improvement of the product, SELT Sp. z o.o. reserves the right to introduce changes, which, while maintaining

significant technical parameters, will be considered as appropriate for increasing the quality of product operation and

safety of use.

Copyrights for this documentation remains with SELT Sp. z o.o. with its registered office in Opole. This documentation may

not be used in any way, either in whole or in part, without the permission of SELT Sp. z o. o.

Translated from the original manual

DT-E 5.7: SYSTEM VERANDA V ZIIIP –SYSTEM PERGOLA V ZIIIP

Edition 3 / March 2021 / EN page 7 / 40

2PRODUCT TECHNICAL INFORMATION

Technical specifications of the product are available after logging in on website www.selt.com

2.1 TECHNICAL PARAMETERS:

Veranda V ZIIIP - single-module veranda version with guide rail brackets

Translated from the original manual

DT-E 5.7: SYSTEM VERANDA V ZIIIP –SYSTEM PERGOLA V ZIIIP

Edition 3 / March 2021 / EN page 8 / 40

Pergola V ZIIIP –terrace awning version single-module with front posts

Translated from the original manual

DT-E 5.7: SYSTEM VERANDA V ZIIIP –SYSTEM PERGOLA V ZIIIP

Edition 3 / March 2021 / EN page 9 / 40

Pergola V ZIIIP

Module dimensions:

Width of single

module

Projection

Maximum

height of the

front posts

Tilt angle

adjustment

range –pergola

version

Tilt angle

adjustment range

- veranda version

Supporting structure

up to 5000

up to 6000 mm

2450 mm

from 10° to 45°

from 0° to 45°

Axial spacing of mounting:

Cassette:

Guide rail

brackets:

Front

supports for

the guide

Support beams

Height of

mounting

brackets

Single

Modular

Maximum:

1600 mm

2870 mm

5700 mm

1900 mm

250

200

Scope of use / exploitation

+5 to +40°C (opening / closing of the fabric)

- 30 to +50°C (supporting structure)

Air humidity

90% no steam condensation (opening / closing of the fabric)

to the full extent (supporting structure)

Fabric:

Serge 100 / Serge 600 –in accordance with the current price list

Fabric tensioning system:

Pneumatic: gas springs ST500 600N, jump 500mm, length 1075mm

Electric drive - motor with the following parameters

- supply voltage

230V/50Hz

- power

270 W

- power consumption

1,2 A

- protection level

IP 44

- torque

40 Nm

- rotation speed

17 rpm

- operating temperature

up -10 to +40°C

Technical data of electric motors

Drives (types of drives):

-remotely controlled electromechanical drive

Connection to the electrical system

Power cord fixed with a Hirschmann plug (not for Somfy IO)

Support beams:

Fabric supporting tubes from 1 to 2 pieces, depending on the size

Installation:

Application

External

Site installation

-Single or multi-module

-on mounting brackets to the load-bearing surface or on the cassette and front

supports

-To the ground or to the wall (structural element) and the ground

Translated from the original manual

DT-E 5.7: SYSTEM VERANDA V ZIIIP –SYSTEM PERGOLA V ZIIIP

Edition 3 / March 2021 / EN page 10 / 40

Detailed data for parameters of the individual motors are available on the websites of motor manufacturers and on the

website:

https://www.selt.com/automatyka-en

2.2 PRODUCT SPECIFICATION

Products manufactured by SELT Sp. z o. o. have appropriate technical and operational parameters.

List of product types:

Installed outside the building, started by electromechanical drive connected with the control system,

Single and multi-module versions connected in width direction,

wall-mounted version (with front supports) or self-supporting version (with mounting brackets).

They have the following features:

Electric movable roof.

Possibility of modular assembly.

They do not protect against rain and snow.

The system is not rainproof and should be rolled up when it rains.

It is forbidden to unroll the fabric during rain, snow or sub-zero temperatures.

They protect against excessive penetration of sunlight in their outline, protect surfaces against heating, thus

contributing to the improvement of thermal comfort in terms of their outline.

Includes a special fabric tensioning system provided by a belt and gas spring assembly.

Possibility of using mounting brackets and cassette mounting brackets or front supports and cassette mounting

brackets.

It is possible to set the inclination angle of the cover in the range of 10° to 45° (assembly with the use of front

supports) or from 0° to 45° - version (assembly on mounting brackets).

They do not emit toxic substances during operation.

Noise emission by a product with an electromechanical drive (associated with the working movement of moving

parts, produced by an electric motor during operation) is not considered a significant hazard and is a matter of

comfort.

Motors have cover protection degree not worse than IP 44.

The construction of the product and the drive allows for safe stopping of the movable roof cover in any position

within the working area and remaining there in a state of rest.

The movement of the movable roof (rolling up and unfolding) can be activated by a manual switch or remotely

controlled.

Covers of moving parts have been designed and made in a way that ensures safety for the operators, assuming

that they are properly operated.

Note:

Deflection/sagging of the fabric does not cause incorrect operation of the system and is not a defect of

the product.

Table of contents

Other SELT Tent manuals

SELT

SELT SUNBREAKER 500 User manual

SELT

SELT SB400 PRO User manual

Popular Tent manuals by other brands

OZTENT

OZTENT JV SIGNATURE EDITION owner's manual

GigaTent

GigaTent Summer Chalet Mini Tent owner's manual

Coleman

Coleman 2000007827 Setup instructions

ShelterLogic

ShelterLogic 107153 Assembly instructions

Outsunny

Outsunny 84C-230 manual

Napier

Napier SPORTZ COVE 61 Series instructions

EuroTrail

EuroTrail ATLANTIS PRO manual

Reimo

Reimo Marina instructions

TiiTENT

TiiTENT TB300 manual

Coleman

Coleman 2000033134 Assembly & instruction manual

Ozark Trail

Ozark Trail W784.1 Assembly instructions and owner's manual

SlingFin

SlingFin CrossBow 2 instructions

Coleman

Coleman 9600-141 instructions

Palram

Palram Arizona 5000 Wave - WINGS manual

COVERPRO

COVERPRO 56184 Owner's manual & safety instructions

Vango

Vango Zenith 100 instructions

Costway

Costway PATIOJOY OP70818 user manual

Clarke

Clarke PUC 88 Assembly guide