Seko PoolMatch pH User manual
0000138883 rev. 1.0
PoolMatch
pH · ORP
INSTRUCTIONS MANUAL
HANDBUCH
MANUAL DE INSTALACION
MANUEL D’INSTALLATION
MANUALE D’INSTALLAZIONE
EN
DE
ES
FR
IT
0000138883 rev. 1.0
PoolMatch | pH · ORP
0000138883 rev. 1.0 EN
1
1. PACKAGE CONTENT
*The values from the table represents the number of items inside the package.
A: Tapping saddle
for securing PSS3
onto 2” hose
(=50 mm)
B: Foot filter
(PP riser)
C: Mounting
bracket kit
(=6 mm screws)
D: FPM Lip valve
(3/8” GAS)
E: PSS3 probe-
holder (1/2” GAS)
F: pH probe
G: Redox probe
H: pH 7 Buffer
solution
I: pH 4 Buffer
solution
J: 475 mV
Calibration solution
K: Water
L: 4x6 (IDxOD mm)
PVC tube (4m)
M: 4x6 (IDxOD mm)
PE tube (5m)
N: Reducer for
injection valve
(1/2” M to 3/8” F)
Item*
System
A
B
C
D
E
F
G
H
I
J
K
L
M
N
PoolMatch pH
2
1
1
1
1
1
-
1
1
-
1
1
1
1
PoolMatch ORP
2
1
1
1
1
-
1
-
-
1
1
1
1
1
WARNING!
Before carrying out ANY work inside control panel of the PoolMatch
device, make sure you disconnect it from the power supply.
Failure to comply with the instructions contained in this manual
could cause injury to people and/or damage to the appliance and
the system.
PoolMatch | pH · ORP
0000138883 rev. 1.0 EN
2
WARNING!
These products are DANGEROUS and require special precautions during use, handling and storage.
•NEVER mix chemical products.
•NEVER allow children or people who have not read this manual to use or tamper with PoolMatch or any
of its peripheral components (including chemical products).
pH chemical products:
•ABSOLUTELY not recommended => pure sulphuric acid
•Recommended for lowering pH => negative pH (with a sulphuric acid base)
•Recommended for raising pH => positive pH (sodium carbonate or bicarbonate)
ORP chemical products:
•ABSOLUTELY not recommended => all types of organic chlorine
The pH / ORP probes are subject to wear and tear and therefore are not covered by the warranty.
2. INSTALLATION INSTRUCTIONS
Use with salt chlorinator:
For the pH systems, to prevent the
risk of system malfunctioning or
damage, observe the following
instructions:
1. Position the pH measuring
probe prior to the chlorinator
cell.
2. To eliminate eddy currents,
connect the pool water to an
electrical ground point
3. Position the product injection
point after the chlorinator cell.
The probe’s angle of
inclination must never
exceed 45° from
vertical.
For optimum probe
reading, position it
perpendicular to the
tubing.
Probe positioning
Installation plant
Warning!
Make sure that the injection pressure is below 1.5 bar
2 m
Warning!
PoolMatch | pH · ORP
0000138883 rev. 1.0 EN
3
3. ELECTRICAL CONNECTIONS
Connect the power supply cable to the mains and the servocontrol pre-wired cable to the auxiliary contact of the
filter box (230 Vca).
Wiring diagram:
1. Input Level Probe (Product Tank)
2. Input Frequency signal by Water meter pulse sender
3. RS485 Serial Port (optional)
4. Input Temperature Probe (PT100 sensor not included)
5. Output Relay Auxiliary Pump (Dry contact, Relay 250 Vac 10 A)
6. Output Relay Alarm remote (Dry contact, Relay 250 Vac 10 A)
4. TECHNICAL SPECIFICATIONS
Specifications
PoolMatch pH
PoolMatch ORP
Measure range
3.0 ÷ 10.0 pH
200 ÷ 999 mV
Set Point range
6.0 ÷ 8.0 pH
400 ÷ 850 mV
Alarm range
5.0 ÷ 9.0 pH
300 ÷ 900 mV
Accuracy
± 0.04 pH
± 2 mV
Resolution
0.01 pH
1 mV
Power supply
230 VAC 50 Hz
Insulation class
II
Consumption
10 W
Pump flow rate
1.6 l/h
Max. back-pressure
1.5 bar
Probe calibration
Automatic
Pump state
Proportional dosing
Peristaltic tube (ID x OD mm)
Norprene 4.8 x 8 mm
Dimensions (H x W x D mm)
185 x 124 x 110 mm
Weight
1.0 kg
Recirculating pump
230V
1
2
3
4
5
6
PT100 temperature probe
2 wires 3 wires
4
PoolMatch | pH · ORP
0000138883 rev. 1.0 EN
4
5. SETUP INSTRUCTIONS POOLMATCH SYSTEM
Program Setup –Press for 5 seconds
At the entry of each menu item, the parameter can be directly modified using the arrow keys ( and ).
Confirmation of the current setting and switching to the next item is done by pressing the button.
The menu has a circular structure: once you arrive at last item, the confirmation of the parameter set by
pressing , determines the return to the first menu item.
1 –It is possible to select between 5 available languages: EN, FR, IT, DE, ES
2 –7.4pH (5-9pH) / 700mV (300-900mV)
3 –Acid (Acid/Alka) / Low (Low/High)
4 = 30seconds (range from 1 to 360 seconds)
5 = 60seconds (range from 1 to 360 seconds)
4
4.1 –(Enabled/disabled)
4.2 –(Auto/Manual 25°C)
4.3 –(0-60min.)
4.4
This menu is available only for models that have the RS485 Modbus connector
▪Baud Rate (2400, 4800, 9600 or 19200)
▪Polarity (Even, Odd or None)
▪Address (from 1 to 240)
▪RS485 Watchdog (Off, 1-30000 seconds)
▪Watchdog Config (Hardware Reset, Watchdog Alarm, Stop Dosing, Reset Comunication)
4.5
▪Pulse/ liter 1:1
▪Unit measure m³, l.
4.6
▪Two points
▪Single point
▪Referece
4.7
▪On/Off
▪Timed
▪Prop
▪Off
1) Button to increase the value
2) Button to decrease the value
3) Button Menu/Esc
4) Button Cal/OK
5) Button to set the setpoint
6) Digital display
1
2
3
4
5
6
* Timed dosing only
PoolMatch | pH · ORP
0000138883 rev. 1.0 EN
5
Save and exit Program setup –Press
Pressing the key determines the exit from the programming menu with saving of the parameters, if the
parameter of the menu item in which one is in has not been changed when pressing the key.
Set Point adjustment
Press the button for 3 seconds, use and to set the desired value.
Stand-by mode (backlight on)
Press and buttons simultaneously for 5 seconds to switch off the unit backlight. Dosage and
calibration are disabled. To exit standby, press and buttons simultaneously.
Priming
Only while the pump is in stand-by press down and in the same time.
Flowrate counter reset
To reset value of "Permanent Totalizer" press button for 3 seconds, in stand-by mode only.
Offset/Slope Menu
Press and buttons the unit show Offset/Slope calibration value, press or to scroll the
menu.
°
Alarm list
- LEV
- WDG
- OFA1 & OFA2
- Stand By
- Flow
Flowater totalizer
Absolut
Resetable
Temperature
measure
pH/ORP
measure
PoolMatch | pH · ORP
0000138883 rev. 1.0 EN
6
6. pH CALIBRATION
5 s
Set pH calibration
4 pH
60 s
7 pH
60 s
4 pH calibration
7 pH calibration
H2O
Save and exit
16
15
13
14
12
9
10
4
5
6
7
1
2
3
8
11
PoolMatch | pH · ORP
0000138883 rev. 1.0 EN
7
7. ORP CALIBRATION
5 s
Set ORP calibration
475mV
60 s
H2O
475 mV calibration
Save and exit
9
10
4
5
6
7
1
2
3
8
11
PoolMatch | pH · ORP
0000138883 rev. 1.0 EN
8
8. PROPORTIONAL DOSING
Setpoint = 7.4 pH
Dosing mode = Acid
Setpoint = 700 mV
Dosing mode = Low
This manual suits for next models
1
Table of contents
Languages:
Other Seko Water Pump manuals
Seko
Seko KOMPACT DPT User manual
Seko
Seko OPL Mini L Manual
Seko
Seko OPL BASIC User manual
Seko
Seko SAM 5-ME User guide
Seko
Seko TDS Series User manual
Seko
Seko MSA Series User manual
Seko
Seko KOMPACT AMC User manual
Seko
Seko AKTUA ATR-05S Manual
Seko
Seko KOMPACT AMC 200 User manual
Seko
Seko KRONOS 50 User manual
Popular Water Pump manuals by other brands
Sykes AmeriPumps
Sykes AmeriPumps GP100M Operation and maintenance instructions
DUROMAX
DUROMAX XP WX Series user manual
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 operating instructions
Franklin Electric
Franklin Electric IPS Installation & operation manual
Xylem
Xylem e-1532 Series instruction manual
Milton Roy
Milton Roy PRIMEROYAL instruction manual