Seiko H024A Quick start guide

Movement

Item H024A

Jewels

Cal. No.

—

[SPECIFICATIONS]

•Hourly time signal

•Alarm test system

•Sound for button operation confirmation

•Battery life indicator

Additional mechanism

Monthly rate within normal temperature range: less than 15 secondsLoss/gain

Nil

Regulation system

Use 10-second gate.Measuring gate by quartz tester

SB-BU (SR1130W)

Battery life is approximately 3 years.

Voltage: 1.55V

Battery

(x 1.2)

Movement

size

Outside diameter ø31.0 mm

29.0 mm between 3 o’clock and 9 o’clock sides

28.5 mm between 12 o’clock and 6 o’clock sides

ø30.0mm

29.0 mm between 3 o’clock and 9 o’clock sides

28.5 mm between 12 o’clock and 6 o’clock sides

Casing diameter

5.5 mm

Height

Analogue section Digital sectionTime indication

Driving system Multiplex driving system

Step motor, 1 piece

2 hands

(Hour and minute hands)

Nematic Liquid Crystal, FEM (Field Effect

Mode)

•Time/calendar display

• Hour, minute and second

• Selection of 12h/24h-format indication

• Year, month, date, day of the week and

fully automatic calendar between the year

2006 and 2055

•Stopwatch display

•Hour, minutes, seconds and 1/1000

seconds

• Up to 23 hours 59 minutes 59 seconds and

999

• Data recall function

•Alarm display

• Daily alarm (2 channels)

•Timer

• Up to 23 hours and 59 minutes

•Time display

• Hour and minute hands, two

hands straight 10-second

increments

Display system

Cal. H024A

2 jewels

PARTS CATALOGUE /TECHNICAL GUIDE

PARTS CATALOGUE Cal. H024A

2/7

●For the part 6, please see the remarks on the following pages.

Disassembling procedures Figs. :

Reassembling procedures Figs. :

Lubricating : Types of oil Oil quantity

Moebius A

Moebius F

Silicone Oil 500,000 c.s.

Normal quantity

* Do not disassemble the

buttons except when

they need to be replaced.

Case back

Case back gasket

Movement

Hour, and

minute

hands

Dial

Button spring clip

Piezoelectric element

Button D

Button C

Button B

Button A

5Dial ring

Case ring

(AO-3)

(AO-2)

Cal. H024A

PARTS CATALOGUE

3/7

●For the parts , , , and , please see the remarks on the following pages.

ql wd e;8q;

Battery connection (–)

4270 380

Buzzer lead terminal

4246 368

Dial washer

0491 233

Insulator for circuit block

4216 366

Connector guard

4398 371

Connector guard screw

0012 316

Connector

4313 366

Liquid crystal panel

Liquid crystal panel frame

4540 366

0012 316

• Connector guard screw

(2 pcs.)

0012 168

• Switch spring screw

(2 pcs.)

• Train wheel bridge

screw(1 pc.)

• Coil block screw

(1 pc.)

Battery

(See the front page.)

Switch spring screw

0012 168

Train wheel bridge screw

0012 168

Train wheel bridge

0125 366

Intermediate center wheel

and pinion (B) 0817 155

Step rotor

4146 154

Coil block screw

0012 168

Coil block (B)

4002 366

Coil lead terminal

4246 367

Center wheel and pinion

Intermediate center wheel

and pinion (A)

0817 154

Hour wheel

Minute wheel and pinion

0261 380

Main plate

Switch spring

Rotor stator (B)

4239 454

Circuit block

4004 139

0100 366

PARTS CATALOGUE Cal. H024A

4/7

Remarks

•Discrimination of the hand installation height

These parts are determined by the hand installation height. Refer to the table below to choose the

appropeiate part.

The caliber H024A has numerals to indicate the hand installation height, which is printed on the dial and

movement.

Standard typeStandard typeHeight

Numeral for

discrimination

Printed position

Printed on Dial Movement

Discrimination

Hour wheel

Center wheel

and pinion

Numeral for

discrimination

0221 607 0271 489

Part code

The numeral is printed at the

right end. The numeral is printed

below the caliber number.

• In a case where the numeral for discrimination is not printed on the movement (switch spring), see the

numeral printed on the dial or refer to the table above to identify each part by its shape.

Switch spring (standard type)

4250 010

Liquid crystal panel

The type of liquid crystal panel differs depending on the model. Refer to "SEIKO Watch Parts Catalogue (CD-

ROM)" or "Watch Parts Catalogue (SEIKO Watch Service Site)" to choose the appropriate type of the crystal

panel.

● Piezoelectric element 4589 006

Piezoelectric element, which is adhered to the case back, can be provided independently.

Center wheel and pinion Hour wheel

5/7

TECHNICAL GUIDE Cal. H024A

AC terminal

Tweezers Switch spring

I. STRUCTURE OF THE CIRCUIT BLOCK

2. To reset the circuit of the watch with its case back

closed, press the buttons “A”,”B”, “C” and “D” at the

same time and hold them for 2 to 3 seconds until the

display becomes blank. Then release the buttons and

check that the display shows “12:00’00” AM, Sunday,

January 1st” .

* Before closing the case back, apply a small quantity of

sillicon oil to the contact portion of the case back with

the buzzer lead terminal (piezoelectric element).

3. Be sure to set the digital time first before setting the

analogue time, as the analogue section is governed by

the "second" of the digital section.

* For time/calendar setting, refer to the instruction booklet

of each caliber.

1. After the battery is replaced with a new one, or after the

battery is re-installed following the repairing

procedures, be sure to short-circuit the AC terminal of

the circuit block and the switch spring with conductive

tweezers to reset the circuit as illustrated at right.

II. REMARKS ON INSTALLING THE BATTERY

H024A

Upconverter coil

Crystal unit

AC terminal

Input terminal (–)

Buzzer output terminal

C-MOS-IC

Input terminal (+)

Coil output terminal

• The explanation here is only for the particular points of Cal. H024A.

• For the repairing, checking and measuring procedures, refer to the “TECHNICAL GUIDE, GENERAL

INSTRUCTIONS.”

6/7

TECHNICAL GUIDE Cal. H024A

III. REMARKS ON DISASSEMBLING AND REASSEMBLING

1. Set the switch spring in position, taking care not to

damage the two guide pins for the main plate. Then,

tighten the two switch spring screws.

• How to install

Battery

Switch spring

2. Make sure the two hooks of the switch spring engage

the main plate.

3. Insert the battery sideways, and have the hook of the

switch spring’s battery clamp portion catch the main

plate.

Use the universal movement holder for disassembling and reassembling.

Hour and minute hands

• Remarks on installing

After installing the battery in the movement, place the move-

ment on a flat metal plate or the like to install the hands.

* Install the hour and minute hands at the 12 o’clock position

within 60 seconds after resetting the circuit.

• Remarks on removing the hands

When using a tool such as a bow-shaped hand remover,

exercise care so as not to damage the dial with the tool during

the hand removing process. Remove the hands either in the

direction of 2 o'clock and 8 o'clock or in the directions of 4

o'clock and 10 o'clock.

H024A

Guide pin

Hook

Battery clamp portion

Main plate

Switch spring screw

7/7

TECHNICAL GUIDE Cal. H024A

IV. VALUE CHECKING

1.3KΩ~ 1.5KΩ

•Time accuracy

To measure the accuracy, light up all the segments. To do so, press buttons “C” and “D” at the same

time in the TIME/CALENDAR SETTING display.

After the measurement, press any one of the button “A”, “B”, “C” or “D” to return to the TIME/

CALENDAR display.

•Coil block resistance

140Ω~ 200Ω

•Upconverter coil resistance

•Current consumption

For the whole movement : less than 3.76μA

For the circuit block alone : less than 1.3μA

Notes:

• Before measuring the current consumption, be sure to reset the circuit. Otherwise, current consumption

cannot be measured properly.

• When the current consumption for the whole movement exceeds the standard value, measure the

current consumption for the circuit block alone. If the result is within the standard value range of the

current consumption for the circuit block alone, overhaul and clean the movement parts and then

measure the current consumption for the whole movement again.

Table of contents

Popular Watch manuals by other brands

Pandora

Pandora WATCH2 quick guide

Casio

Casio QW-4343 Service manual

Suunto

Suunto X6 user guide

MotionX

MotionX 365 user guide

Garmin

Garmin VENU SQ 2 owner's manual

QCY

QCY Watch GTC manual

Canyon

Canyon Cindy CNE-KW41WP quick guide

Esq

Esq Watches Operating instructions warranty & service guide

Crane

Crane AA5-CDSM-3A user manual

Timex

Timex W-214 product manual

DETOMASO

DETOMASO MATERA manual

Geemarc

Geemarc Watch N Shake user guide

LORUS

LORUS W590 instruction manual

STENLILLE

STENLILLE Actío user manual

Casio

Casio 5594 Operation guide

Sinn

Sinn HUNTER'S WATCH 3. Edition manual

Slazenger

Slazenger SLZ800 manual

iTOUCH

iTOUCH 3360 user manual