SEGUE VK-1314 Manual

Order #XXXXX

Top View

Perspective View

10’

Scale: 19

VK-1314 General Layout

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

Order #XXXXX Grid Layout

Locked layer contains

placeholder marks.

= 1 sq foot

Order #XXXXX

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

Part Identification - Numbering

Spline Connection Base Plate & Extrusion Connection

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

WARNING

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all set screws

and locks during disassembly.

Hex Tool - Essential for Assembly

Extrusion & Lock Connection Engaged Lock

LADDERS OR LIFTS

MAY BE REQUIRED

General Information

Order #XXXXX

Graphic Removal

To remove the graphic

the frame, locate the fabric

pull tab.Gently pull up on the

tab to remove the fabric.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

It is important to first insert

graphic into each alternate

corner then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Corner A

Corner D

Corner B

Corner C

from

SEG Installation

Case 1 of 3

Order #XXXXX Case Packing

Graphics

Lights

Setup Hardware

Top View of Each Level

Level 1 (Bottom Level) Level 2

13 17

16A 2 2A 3 3A 15 4 4A 5 5A

7,7A

8,8A

1,1A

6,6,6A,6A

Level 3

Case 2 of 3

Order #XXXXX Case Packing

Top View of Each Level

Level 1 (Bottom Level) Level 2

Counter

9,9A

11,11

12,12

Shelf

(Qty. 2)

Shelf

(Qty. 4)

Level 3 Level 4

Canopy Pieces

Shelf

(Qty. 2)

Shelf

10,10A

Case 3 of 3

Order #XXXXX Case Packing

Locked layer contains

placeholder marks.

Top View of Each Level

Level 2 Level 3 Level 4 Level 5

Counter Top (2) Side Panels Front Panel

Shelf

Floor

Shelf Supports

Back Panel w/ Door

Level 1 (Bottom Level)

Step 1 of 4

Order #XXXXX VK-1314 Backwall Assembly

Counter

Flange

10 10A

Bolt Bolt

6786

7A 8A 6A

Canopy

Mount

Item

1,1A

2,2A

3,3A

4,4A

5,5A

6,6A

7,7A

8,8A

9,9A

10,10A

Description

Base Plate

42” S44 Vertical Extrusion w/ PR37

42.25” S44 Vertical Extrusion w/ TSP3 & PR37

42” S44 Vertical Extrusion w/ TSP3 & PR37

42” S44 Vertical Extrusion w/ PR37

14” Z45 Horizontal Extrusion

28.9725” Z45 Horizontal Extrusion w/ TSP3

11.0128” Z33 Horizontal Extrusion

11.8331” Z33 Horizontal Extrusion

44.3283” Curved Vertical Extrusion

14” Z140 Horizontal Extrusion

19” Z45 Horizontal Counter Support

31.945“ Vertical Counter Support

Qty.

1,1

2,2

1,1

Steps:

1) Attach base plate [1] to vertical [2] and [15].

2) Attach base plate [1A] to vertical [5].

3) Attach all upper verticals to lower verticals.

4) Connect horizontals [7 to 8] and [7A to 8A].

5) Connect curved verticals [11] to [12].

6) Attach horizontals between vertical as shown, making sure Velcro is facing to back.

7) Attach horizontal [14] between to verticals [2] and [15].

8) Place counter on top of horizontal [14]. See Counter Attachment detail to secure.

9) Apply SEG graphic to TSP3. See SEG Installation sheet for instruction.

10) Connect graphics to Velcro on back of PR37 extrusions.

Velcro at lower

back of bar. Velcro at lower

back of bar.

Velcro at upper

back of bar.

Velcro

PR37

Extrusion

Profile

Completed Assembly

Velcro at upper

back of bar.

Counter Attachment

Wing Nut

Fixed

Screws

Flange

Counter

Attach flange to extrusion [15], using screw.

Insert fixed screws, located on underside of

counter, into holes of flange then secure

with wing nuts.

Keep canopy mounts attached

to [2A] and [5A], when packing.

Step 2 of 4

Order #XXXXX

Using Your Setup Instructions

The Aero Setup Instructions are created specifically for your configuration. The instructions include an

exploded view of the frame which is sequentially labeled. We encourage you to review the instructions

before attempting to assemble your exhibit.

Connections are kept very simple; no tools required. Everything assembles with push-button connectors.

Cleaning and Packing Your Display

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.

2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood

of shipping damage.

Connections are made by holding the button down and

sliding the red tube into opposing tube until the connection

is made. To disassemble push button and pull or twist

extrusions apart.

Push-Button

Numbered Label

Steps:

1) Connect canopy pieces together as shown.

2) Apply pillow case graphic to assembled canopy

Push-Button

Push button then rotate

for packing purposes

Canopy Assembly

Step 3 of 4

Order #XXXXX VK-1314 Backwall Attachments

Completed Assembly

Header Assembly

Canopy

Keep header assembled,

when packing.

Header

Shelves

Screw

Cap

Screw

Cap

Shelves

16A

17 7A

2A 13

Item

16,16A

Description

8” Z45 Vertical Extrusion

38.5928” Z45 Curved Horizontal Extrusion

Qty.

1,1

Steps:

1) Attach assembled header to top horizontals [7A/8A],

making sure header Velcro faces to back.

2) Connect graphic to Velcro on back of assembled header.

3) Attach lights. See Light Attachment detail.

4) Place canopy on top of vertical [2A] and [5A] mounts.

5) Attach shelves to backwall using screw caps and

clamps. See Clamp Attachment detail.

6) Attach monitor mount to horizontal [13]. See Monitor

Mount Attachment detail.

Attach mount plate, using bolts, to Z140

extrusion then secure with wing nuts.

Attach monitor mount to mount plate.

Z140

Extrusion

Wing

Nut

Monitor

Mount

Plate

Monitor Mount Attachment

SEG Graphic

When desired location

is found, tighten

set screw to secure.

Slide connector, located on

back of clamp, into groove

of extrusion.

Clamp

Clamp Attachment

Keep clamps attached to verticals, when packing.

Knob

Set Screw

A10 Clamp

Slide light onto clip then lock clip

into groove of horizontal extrusion.

Clip

Light

Light Attachment

Clip

Light

Horizontal Extrusion

Table of contents

Popular Display Case manuals by other brands

Hatco

Hatco FLAV-R-SAVOR FSCD Series Installation and operating manual

Bonnet Neve

Bonnet Neve SKYLIGHT User instructions

True

True TCGD-50 installation manual

Tecnodom

Tecnodom EVO SELF User and maintenance manual

Delfield

Delfield F15SC48N Specification sheet

saro

saro FIONA instruction manual

Hendi

Hendi 233962 user manual

Hoshizaki

Hoshizaki HNC-120BE-L-BLH instruction manual

Nordcap

Nordcap GENIUS 2 H145-L70 manual

Omcan

Omcan RS-CN-0140-D instruction manual

Tecnodom

Tecnodom M Series User and maintenance manual

freor

freor MERCURY Operation manual

Costan

Costan WHALE 2000 G LG300 User instructions

Costan

Costan IMPALA User instructions

True Manufacturing Company

True Manufacturing Company TCGD-50 installation manual

Bartscher

Bartscher 100L instruction manual

Steelcase

Steelcase Opus Assembly instructions

Hatco

Hatco Glo-Ray GRHD-2P Replacement parts list