Seeworld S702 User manual
1
GPS+GSM+SMS/GPRS+OBD II
S702 User Manual
V1.0
2
User Manual
Welcome to use SEEWORLD GPS
Tracking terminal，please read this manual
carefully to install and operate the terminal
exactly. This user manual is for reference
only. If some contents and operation steps
are inconsistent with those for the actual
product, the latter will prevail.
Using the GPS tracker, we can
position,monitor the vehicle including OBD
data on the position server via GPRS,GPS
and Internet. It can help customers to
manage transparently,reduce
cost,maintain security and raise efficiency.
Now it is widely used in business traffic,
logistics distribution,automobile lease,
intelligent transportation, shipping
market,army and police,rescuing,Safety
Supervision,Intelligent city…
There are two different functions to suit
different needs :
A：GPS+OBD II
B：GPS only
3
Ⅰ. Product Features
■Supports quad bands,
i.e. 850/900/1800/1900MHz,
universal in the world.
■Easy to install, connect the OBD interface to
work.
■Supports single positioning and feedbacks
position via GPRS at setting times.
■Supports vehicle positioning and tracking.
■Vehicle status and speed from OBD data is
better than ACC.
■Vehicle collision, falling alarm by
SMS/Platform (optional).
Ⅱ. Components & Accessories
2.1 Components
4
-Top Front(Up side)-
-Top Back-
2.2 Accessories（reference
pictures）
5
OBD II Extension Cable
Optional accessory for the device, when the
OBD interface is not very good and the GPS
signal is poor, we can use an extension cable
to strength GPS signal.
Ⅲ. Environment for use
1. Limited working temperature：-20℃~80℃
2. Storage temperature：-45℃~90℃
3. Humidity：<95%
4. sure the terminal is installed in OBD2 interface
of the vehicle
Ⅳ. Basic Specifications
Voltage 12VDC/24VDC
6
Standby Current <3mA
Work current <120mA
GPS positioning
accuracy 15m
GSM positioning
accuracy 100m
GPS Frequency 1575MHz
GSM Frequency 850/900/1800/1900MHz
Hot/warm/cold start
time <3s，<15s，<60s
Dimensions (mm) L*W*H：56.5 X 47 X 24.6
Net Weight 45 g
Ⅴ. Installation
5.1 Before Installation
5.1.1 Open the packing case, then check if the
terminal is Ok and the accessories are intact, or
please contact your dealer;
5.1.2 Choosing a SIM card: You need a suitable
SIM card for using the terminal, please contact your
dealer if you have any question;
5.2 Install the SIM card
7
Pinch the sides of the front cover with one hand, the
other hand gently open the back cover.
8
First use your thumb to press the SIM card cover,
then push it outside to pull down the SIM card
cover.
ow you can insert your SIM card.
9
Turn the installed SIM card holder door to its
original position, gently push the lid with your
fingers so it is locked.
Close the back cover, use a screwdriver to
packaging the two screws into the the back cover.
Ⅵ. Set up the terminal
Please refer to the Operation Commands
Ⅶ. Use the terminal
7.1 Power on
Connect terminal to the vehicle OBD2 interface and
it wll power on.
10
7.2 LED indicators
The red LED flickers fast when the terminal is
searching for GSM network, it flickers intermittently
when the terminal has registered the GSM network
successfully.
The blue LED flickers fast when the terminal is
searching for the GPS satellite signal, it flickers
intermittently when the terminal when the terminal
has searched the satellites and can be positioned.
7.21 Red LED(indicates GSM working state)
Fast flicker Searching for GSM
network
Intermittently flicker GSM/GPRS works
normally
Table of contents
Other Seeworld GPS manuals
