Sealey AK714.V2-01 User manual
INSTRUCTIONS FOR:
BLIND BEARING PULLER SET - 5PC
2. INTRODUCTION
1. SAFETY
3. CONTENTS
26mm - 32mm Attachment (Part No: AK714.V2-01)
20mm - 25mm Attachment (Part No: AK714.V2-02)
Slide hammer (Part No: AK714.V2-03)
15mm - 20mm Attachment (Part No: AK714.V2-04)
11mm - 15mm Attachment (Part No: AK714.V2-05)
WARNING! Ensure that Health and Safety, local authority and general workshop practice regulations are
adhered to when using this product.
DO NOT use this product if damaged.
Maintain product in good and clean condition for best and safest performance.
If the vehicle to be worked on is raised, ensure that it is adequately supported with axle stands or ramps and chocks.
Wear approved eye protection. A full range of personal safety equ
Wear suitable clothing to avoid snagging. Do not wear loose jewellery and tie back long hair.
Account for all tools and parts being used.
If working off the vehicle, secure the work piece in a vice or clamp it to a work bench.
DO NOT operate puller if you are tired or under the influence of alcohol, drugs or intoxicating medication.
IMPORTANT: Always refer to the vehicle manufacturer’s service instructions, or a proprietary manual, to
establish the current procedure and data. These instructions are provided as a guide only.
2.1. Introduction
Fully chromed carbon steel medium stroke slide hammer. 370mm Overall length with 1.4kg hammer. Bearing
extractor collets with internal capacity from 11 to 32mm. Supplied in carry-case.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
ipment is available from your dealer.
4. INSTRUCTIONS
4.1. Prior to use of the required
attachment, disassemble and
grease as shown in fig.1.
Reassemble the attachment.
4.2. Screw the attachment into the
shaft, as shown in fig.2. Tighten
the attachment using a wrench.
Note: Do not over tighten.
4.3. Ensure the attachment jaws
are completely closed and insert
the attachment into the inner
diameter of the bearing, fig.3.
4.4 Turn the handle clockwise to
open the attachment jaws to
grip the bearing. See fig.4.
4.5. Hold the bearing puller as shown
in fig.5, slide the hammer to the
bearing end of the shaft and
then forcefully pull the hammer
to the other end of the shaft.
4.6. Ensure the bearing is being
pulled out evenly, if not, remove
the puller attachment and, using
a soft faced mallet, tap the
bearing until it is seated evenly.
4.7. Repeat paragraphs 4.5 and 4.6
until the bearing has been
removed.
4.8. Turn the handle anticlockwise to
close the jaws in order to
release the bearing from the
attachment head. See fig.5.
Loosen
Grease
Attachment Head
Fig.1
Tighten
Fig.2
Bearing
Attachment Head
Fig.3
Attachment Head
Hammer
Open jaws
Fig.4
Attachment Head
Hammer Close Jaws
Fig.5
This manual suits for next models
4
Table of contents
Other Sealey Power Tools manuals
Sealey
Sealey SB997 User manual
Sealey
Sealey STW310 User manual
Sealey
Sealey AK629 User manual
Sealey
Sealey STW307 User manual
Sealey
Sealey YK509F User manual
Sealey
Sealey SA21/S.V3 User manual
Sealey
Sealey SMS2003 User manual
Sealey
Sealey STW309 User manual
Sealey
Sealey CP1209 User manual
Sealey
Sealey SDL12 User manual
Sealey
Sealey SSG8E.V3 User manual
Sealey
Sealey Quality MACHINERY YK6ECB User manual
Sealey
Sealey GSA20.V2 User manual
Sealey
Sealey HCC08 User manual
Sealey
Sealey SB972.V4 User manual
Sealey
Sealey PS981.V2 User manual
Sealey
Sealey SA7/SAS User manual
Sealey
Sealey SA390 User manual
Sealey
Sealey AK6290 User manual
Sealey
Sealey SA609 User manual
