Seafloor TriDrone Programming manual

- TriDrone USV

- TriDrone Carry Case

- TriDrone Hardware Kit

- Data Collector Cable

- Accessory Pouch

-Spektrum Remote

Control with case

-USB Drive

-Mast

IMPORTANT

THANK YOU FOR PURCHASING SEAFLOOR SYSTEMS' PRODUCTS FOR YOUR SURVEYING NEEDS.

Please read through all of these Instructions and tips before proceeding with the operation. We do our best

to provide a simple setup process for all applications however please contact your nearest authorized

dealer if you encounter issues.

Always disconnect any power sources connected to your vessel before servicing vessel or accessories.

PRODUCT INCLUDES:

STEP: 1

Remove the vessel from the

case. Remove the remote case

from the top of the lid. Remove all

accessories from accessory pouch

located at the bottom of the case.

QUICKSTART INSTRUCTIONS

TriDrone Portable Remote Surveying Vessel

QUICKSTART INSTRUCTIONS

STEP: 2

Attach the thruster to the rear bracket of the vessel and secure by tightening

retaining screw.

STEP: 3

Insert fully charged 4S battery

and connect to power

distribution cable.

STEP: 4

Open bow hatch lid with provided hatch wrench,

and remove lid.

STEP: 5

Run the data collector cable through the inside of the hull through to the

hull hatch lid.

QUICKSTART INSTRUCTIONS

STEP: 6

Connect data collector cable to

transducer.

STEP: 8

Connect the thruster cable to the bulkhead

located at the stern of the vessel.

STEP: 7

Attach antenna to the mounting screw located at the front of the frame.

QUICKSTART INSTRUCTIONS

Operation: Be sure to observe and follow all local water safety regulations and procedures. Always

operate vessel within line of sight, and immediately stop operation if hazards or safety risks arise.

Your setup is now complete.

Welcome to the Seafloor Squad!

WARRANTY INFORMATION

For warranty information, visit https://www.seafloorsystems.com/terms-and-conditions 4415 Commodity Way, Shingle

Springs, CA, 95682 • 530-677-1019 https://www.seafloorsystems.com/

STEP: 9

Switch power to the "On" position.

STEP: 10

Connect the remote by holding the power button for

approximately 2 seconds. The remote will beep when

activated. You are now ready to survey.

Table of contents

Other Seafloor Marine Equipment manuals

Seafloor

Seafloor EchoBoat-240 User manual

Seafloor

Seafloor HydroLite-DFX User manual

Seafloor

Seafloor HydroCat 180 User manual

Seafloor

Seafloor Sonarmite User manual

Seafloor

Seafloor AutoNav User manual

Seafloor

Seafloor EchoBoat 160 ASV User manual

Seafloor

Seafloor HyDrone ASV User manual

Seafloor

Seafloor AutoNav PLUS User manual

Popular Marine Equipment manuals by other brands

Clarion

Clarion CMS2 Owner's manual & installation manual

EBS

EBS M7000 installation manual

Kongsberg

Kongsberg M3 Bathy installation manual

NPK

NPK SCS-1002 operating manual

Furuno

Furuno FE-800 installation manual

Harken

Harken 1561 instructions

Simrad

Simrad DD15 manual

Notifier

Notifier FS-BSO Installation and maintenance instructions

Raymarine

Raymarine ST40 Quick reference guide

E2S

E2S E2XS112UL Instructions/service manual

R2Sonic

R2Sonic 2026 Operation manual

COBHAM

COBHAM SAILOR 6000 installation manual

Clarion

Clarion GR10BT Owner's manual & installation manual

Raymarine

Raymarine Maxiview ST80 Owner's handbook

GUIDANCE MARINE

GUIDANCE MARINE 20- Series Installer's guide

Raymarine

Raymarine ST60 Tridata Owner's handbook

olympia electronics

olympia electronics ΒS-531/1/MAR quick start guide

Sonic

Sonic 2024 Operation manual