Scosche HD7000AB User manual
rJ
.SC:O.Sc=f
It:
HD7000AB
AFTERMARKET STEREO INSTALLATION
KIT
FOR SELECT HARLEY-DAVIDSON
2006-2013
FLHX STREET GLIDE,
1996-2013
FLHT
ELECTRA GLIDE
&
1998-UP FLTA ROAD GLIDE MODELS
(WITH FACTORY-EQUIPPED RADIO)
PARTS INCLUDED:
1. DASH
KIT
(1)
Mounting Panel
(2)
Left
&
Right Mounting Brackets
(4)
Screws (bracket attachment)
(2)
Spacers (*Road Glide models only)
2. NEOPRENE GASKET STRIP
(not shown)
OPTIONAL
ACCESSORIES:
(Sold separately)
HDSWC1 Handlebar Control
Interface w/plug and play
harness
HD01
B Power/Speaker harness
(For non-handlebar
control cycles)
7424
LEFT
MOUNTING
BRACKET
7422
MOUNTING
PANEL
INTRODUCTION/PRELIMINARY
7501
SPACERS*
7423 RIGHT
MOUNTING
BRACKET
This premium installation kit is
for
select Harley Davidson Road Glide & Street Glide motorcycles
Included are all the parts you need
to
mountyour carstereo
or
CD playerinto yourbike's dash. Refer
to
the individual instructions in this manual
to
remove your factory radio and assemble the kit.
CAUTION
DISCONNECT THE CYCLE1S NEGATIVE BATTERY.TERMINAL BEFORE THE INSTALLATION TO
HELP PREVENT ELECTRICAL DAMAGE. WE RECOMMEND THE USE OF A VOLT/OHM METER
OVER A TEST LIGHT TO
CHECK
WIRING. A TEST LIGHT OR GROUNDED WIRE PROBE CAN
CAUSE DAMAGE TO THE CYCLE•s COMPUTER
AND/OR
DIAGNOSTIC SYSTEMS.
PREPARATION:
• Work on a clear level surface • Place bike on kickstand with wheel tilted toward the leaning direction
• Use felt
or
soft cloths
to
cover and protect painted surfaces
TOOLS REQUIRED
(not
Included):
T-25/T-27
Torx
1/4''
or
6mm hex drive
3/16''
or
Smm hex drive 7/16'' socket
or
box
wrench (Road Glide models only)
LIABILITY
DISCLAIMER
This manual is
based
on carefully documented research. Absolute accuracy is attempted, but not guaranteed.
Use the manual as a reference guide as your bike may differ. Scosche Industries, Inc. cannot be held responsible for
Inconsistencies that may occur due to vehicle manufacturing changes or options,
or
damage that may occur
to
the vehicle
during the Installation
of
components while using this booklet.
If you have any further questions, call
our
toll free technical help line at:
1·890·621-3695x3
@
2014
SCOSCHE
INDUSTRIES,
INC
..
51
HD7000AB
(3000597) 7/14
FACTORY STEREO REMOVAL
2006-2013
FLHX
STREET
GLIDE
1996-2013
FLHT
ELECTRA
GLIDE
0 Drape a protective cloth over the front fender.
Carefully lift away windshield,
store
in
a safe location and
replace the middle Torx bolt for
support during the remaining
removal steps.
Extract
(3)
T-27 Torx bolts from
bottom edge
of
windshield.
Extract
(2)
T-27 Torx bolts from outer
side
of
the fairing (under mirrors).
2
Extract
(2)
T-27 Torx bolts from
inside the fork tubes (facing
forward).
FACTORY
STEREO
REMOVAL
~
While supporting
the
outer
\.:1
fairing, remove
the
middle
windshield bolt, lift away and
unplug headlight to remove
fairing shell. Store fairing in a
safe place until re-assembly.
Extract
(2)
1,4'' 6mm hex
bolts from each side
of
the radio housing.
Unbolt and remove inner fairing support
brackets from each side (3/16" hex &
T-25 Torx screws) Note
that
the
Torx
screw is also a shared speaker screw.
Carefully
back
the
radio
out
of
the
fairing, unplug wiring
connectors, antenna and
remove
the
radio.
NOTE: Reuse the
(4)
factory bolts
to
mount
the
HD7000B
kit (see page
6)
.
3
FACTORY STEREO REMOVAL
1996-UP
FLTR ROAD
GLIDE
0 Drape a protective cloth over the front fender.
a
DO
NOT remove the windshield on Road Glide models
Extract
(2)
T-25
Torx
bolts
from
bottom
left and
right
sides
of
the
fairing.
Remove the metal strap under
the nuts, and push the studs
out
to remove the signals.
CAUTION: Do not let turn
signals drop
or
dangle.
4
Use a 7
/16"
socket
or
box
wrench to remove
(2)
nuts that
hold the each turn signal at the
lowerfairing.
Extract
(2)
T-25 Torx
bolts from outer left
and right sides
of
the
fairing.
FACTORY
STEREO
REMOVAL
Carefully lift fairing at
headlights
to
release
support hooks, unplug
headlights and remove.
Store fairing
in
a safe place
until reassembly.
NOTE!: Be sure
to
reattach support hooks
during reinstallation.
Have a helper hold on the outer
fairing and extract the last
(2)
T-25
Torx bolts from the upper fairing
nearthe speaker grilles.
Extract
(2)
W'
6mm hex
bolts from each side
of
the radio housing.
Carefully back the radio out
of
the fairing, unplug wiring
connectors, antenna and remove the radio.
NOTE: Reuse the
(4)
factory bolts
to
mount the
HD7000B
kit (see page
6).
5
KIT
ASSEMBLY
REMOVE
SLEEVE
FROM
AFTERMARKET
STEREO
1. Locate the locking mechanism on your
DIN
stereo sleeve
{typically) on the side.
2. Slip mounting sleeve towards rear
of
stereo
and remove {Figure
1).
FIGURE 1
ISO-DIN
MOUNT
ONLY
1. Attach the 7423 and 7424 side brackets
to
the 7422 front
panel using the hardware supplied with the kit (Figure
2).
2. Remove supplied trim ring and sleeve from new stereo.
3. Slide new stereo into kit from rear and fasten within the kit's
brackets using the ISO hardware provided with the stereo.
NOTE: If hardware is not included with aftermarket stereo,
reuse factory hardware.
STEREO MOUNTING BOLTS
(re-use
bo
l
ts
from factory stereo)
FIGURE 2
7424
LEFT
MOUNTING
BRACKET
7422
PANEL
BRACKET MOUNTING SCREWS
' ' ' '
I
(s
upp
lied with
HD7000B
dash
ki
t)
______
.:....._
___,
7423
RIGHT
MOUNTING
BRACKET
'
~-----'
7501
SPACER
(Road Gli
de
models only)
NOTE: Due to variances
in
motorcycle manufacturing, the
HD7000B
dash kit includes a strip
of
Neoprene gasket material for optional use. Ifyou experience a gap around the perimeter
of
the faceplate then use the supplied adhesive backed gasket strip to seal the space.
6
7
Table of contents
