Schumacher SL197U User manual
SL197U
Magnetic Mount Work Light
OWNER’S MANUAL
SL197U
Magnetic Mount Work Light
OWNERS MANUAL
1. IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
1.1 SAVE THESE INSTRUCTIONS – This manual contains important safety and
operating instructions.
1.2 Read, understand and follow all instructions, cautions and warnings listed in this
manual. Failure to follow all instructions and abide by all cautions and warnings
could result in personal injury, injury to others and property damage.
1.3 IMPORTANT! CHARGE WORK LIGHT IMMEDIATELY AFTER PURCHASE,
AFTER EACH USE, AND AT LEAST EVERY 6 MONTHS.
1.4 DO NOT turn on the work light while it is being charged.
1.5 DO NOT handle or move the work light while it is being charged.
1.6 DO NOT look directly into the light or shine the light directly into the eyes of any
person or animal.
1.7 DO NOT allow children to use the work light.
1.8 DO NOT operate the work light if it has received a sharp blow, been dropped, or
otherwise damaged in any way; take it to a qualied service person.
1.9 DO NOT leave the battery in a discharged state.
1.10 DO NOT use the work light with a charger which has a damaged cord or plug,
replace the cord or plug immediately.
2. PERSONAL SAFETY PRECAUTIONS
WARNING! TO REDUCE THE RISK OF BURNS OR FIRE, FOLLOW THESE
SAFETY PRECAUTIONS:
2.1 DO NOT disassemble the work light; take it to a qualied service person when
service or repair is required. Incorrect reassembly may result in a risk of re.
2.2 DO NOT crush, puncture, short external contacts or dispose of in re or water.
2.3 DO NOT expose to temperatures above 140°F (60°C).
2.4 Recycle or dispose of the used battery as required by local regulations.
2.5 If the electrolyte in the cells gets on your skin, wash thoroughly with soap
and water. If it gets into your eyes, rinse thoroughly with cool water and seek
immediate medical attention.
2.6 This product contains a lithium ion battery. In case of re, you may use
water, a foam extinguisher, Halon, CO2, ABC dry chemical, powdered graphite,
copper powder or soda (sodium carbonate) to extinguish the re. Once the re
is extinguished, douse the product with water, an aqueous-based extinguishing
agent, or other nonalcoholic liquids to cool the product and prevent the battery
from re-igniting. NEVER attempt to pick up or move a hot, smoking, or burning
product, as you may be injured.
2.7 WARNING: This product contains one or more chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
3. SET UP INSTRUCTIONS
3.1 Remove any cord wraps and uncoil the charging cable.
4. FEATURES
1. ON/OFF button
2. Charging socket
3. Charging status LED indicator
4. 15 SMD LEDs
5. Sliding magnetic bracket
6. USB/Micro USB charging cable
1 2 3 4 5 6
5. CHARGING
IMPORTANT! CHARGE THE WORK LIGHT IMMEDIATELY AFTER PURCHASE,
AFTER EACH USE, AND AT LEAST EVERY 6 MONTHS. Failure to do this will
reduce the battery’s capacity and may void the warranty.
5.1 Insert the micro USB end of the charging cable into the micro USB port on the
end of the work light.
5.2 Insert the USB end of the cable into the USB port on your charger.
5.3 Plug your charger into a live power source.
5.4 The red charging status LED will light, to indicate charging has begun.
5.5 When the battery is fully charged, the LED will change to green.
5.6 Unplug the unit from your charger.
5.7 Recharge the work light after use, and at least every 6 months.
6. OPERATING INSTRUCTIONS
6.1 Attach the work light to any ferrous metal surface.
6.2 To adjust the work light to the desired position, slide and swivel the magnetic
mounting brackets.
6.3 Press button once to turn on at high power.
Press button a second time to turn on at lower power.
Press button a third time to turn the unit off.
6.4 Recharge the work light after use, and at least every 6 months. VOTING
7. MAINTENANCE INSTRUCTIONS
7.1 After use and before performing maintenance, unplug and disconnect the work light.
7.2 Use a dry cloth to wipe any dirt or oil from the charging cable and case.
7.3 Ensure that all of the work light’s components are in place and in good working
condition.
7.4 Servicing does not require opening the unit, as there are no user-serviceable parts.
7.5 Any servicing should be performed by qualied service personnel.
8. STORAGE INSTRUCTIONS
8.1 Store inside, in a cool, dry place.
8.2 Take care to avoid/prevent damage to the charging cable and unit. Failure to do
so could result in personal injury or property damage.
8.3 Charge the work light’s internal battery immediately after purchase, after every
use and every 6 months.
8.4 All batteries are affected by temperature. The ideal storage temperature is at
70°F (21 ˚C). The internal battery will gradually self-discharge (lose power) over
time, especially in warm environments. Leaving the battery in a discharged state
may result in permanent battery damage. To ensure satisfactory performance and
avoid permanent damage, charge the internal battery every 6 months.
9. TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
The work light does
not operate. The battery is not charged. Recharge the battery to full
charge.
10. DISPOSAL INFORMATION
Do not dispose of this product with other household waste. To prevent
possible harm to the environment or human health from uncontrolled
waste disposal, and to promote the sustainable reuse of material
resources, recycle it responsibly. To discard your used device, please
use the return and collection systems or contact the retailer where the
product was purchased, for environmentally-safe recycling.
11.SPECIFICATIONS
Battery type ...........................................................Lithium Ion, 3.7V, 2200 mAh
Light ............................................................................................... 15 SMD LED
Lumen output ............................................................150 lm (high); 100 lm (low)
Operating time...................................................... 6 hours (high); 12 hours (low)
Charging time.......................................................................................... 3 hours
12.REPLACEMENT PARTS
USB to Micro USB charging cable.....................................................3899003752Z
View other automotive tools made by Schumacher on our website.
Table of contents
Other Schumacher Work Light manuals
Schumacher
Schumacher SL176 Series User manual
Schumacher
Schumacher SL 175R User manual
Schumacher
Schumacher SL 184RU User manual
Schumacher
Schumacher SL879U User manual
Schumacher
Schumacher SL26-GU User manual
Schumacher
Schumacher RED FUEL SL158 User manual
Schumacher
Schumacher SL 137-GU User manual
Schumacher
Schumacher SL184U Series User manual
Schumacher
Schumacher SL26-GU User manual
Schumacher
Schumacher SL175U Series User manual
Popular Work Light manuals by other brands
PowerSmith
PowerSmith PWLD080T Operator's manual
MaxLite
MaxLite 73683 installation instructions
Heitronic
Heitronic Trend 27867 Installation and operating instructions
Monzana
Monzana Gore MZCL10 manual
EINHELL
EINHELL TE-CL 18/2000 LiAC Original operating instructions
Bayco
Bayco NIGHTSTICK Dual-Light Xtreme Lumens... instruction manual