Schletter RAPIDPRO User manual
RAPIDPRO
MODULE CLAMP
INSTALLATION GUIDE
INSTALLING FURTHER MODULES ........................................................... 5
2
RAPIDPRO MODULE C LAMP | V 1 | INSTALLATION GUIDE | 202102
SCHLETTER SOLAR GMBH | SUBJECT TO CHANGES
Table of contents
RAPIDPRO MODULE CLAMP INSTALLATION GUIDE ........................................... 3
TOOLS NEEDED ....................................................................................... 3
TIGHTENING TORQUE ................................................................................... 3
SAFETY INSTRUCTIONS ................................................................................. 3
VERTICAL INSTALLATION ................................................................................. 4
1. PROFILE ARRANGEMENT ........................................................................ 4
2. INSTALLING THE FIRST MODULE ............................................................... 4
3.
4. INSTALLING THE FINAL MODULE ............................................................ 6
NOTE ON DISASSEMBLY ........................................................................... 6
3
SCHLETTER SOLAR GMBH
RAPIDPRO MODULE CLAMP INSTALLATION GUIDE
TOOLS NEEDED
Screwdriver with Bit TX-drive T40 bit holder
TIGHTENING TORQUE
Screw connections M8 : 15 Nm
SAFETY INSTRUCTIONS
Planning, installation and commissioning of the solar power system must only be performed
by qualified technical personnel. Improper execution can result in damage to the system and
premises and endanger persons.
Falling hazard! Working on the roof as well as ascending -and descending poses a risk of
falling. It is vital to observe accident prevention regulations and use appropriate fall protec-
tion equipment.PV mounting systems do not meet the existing normative requirements for
climbing aids or fall protection measures. They are therefore neither suitable as climbing
aids nor as fall protection and must not be used for these purposes.
Injury hazard! Falling objects pose a risk of injury to people. Prior to installation, set up
barriers in the hazard area to warn people nearby.
Break hazard! PV modules may be damaged if stepped on or if handled inappropriately.
Electrical current hazard! Installation and maintenance of the PV modules must only be
performed by qualified technical personnel. Observe the safety instructions issued by the PV
module manufacturer!
RAPIDPRO MODULE CLAMP | V1 | INSTALLATION GUIDE | 202102
SCHLETTER SOLAR GMBH | SUBJECT TO CHANGES
4
SCHLETTER SOLAR GMBH
Vertical installation
1. PROFILE ARRANGEMENT
Check that the arrangement of the module support profiles corresponds to their
module configuration.
Observe the clamping points as per the manufacturer's instructions.
2. INSTALLING THE FIRST MODULE
Place the module on the profile ends.
Align the module.
Click in 2 RapidPro end clamps and tighten the screws (TX-drive T40).
Connect module cables accordingly.
Insert end clamps at least 10 mm from the end of the profile.
RAPIDPRO MODULE C LAMP | V1 | INSTALLATION GUIDE | 202102
SCHLETTER SOLAR GMBH | SUBJECT TO CHANGES
5
SCHLETTER SOLAR GMBH
3. INSTALLING FURTHER MODULES
Click in 2 RapidPro centre clamps.
Place and align the next module.
Connect module cables accordingly.
Tighten screws.
Repeat steps until the last module of the sequence is installed.
Observe module distance (see illustration)
Distance of the modules between the module rows at least 10 mm or in accordance
with the installation guidelines of the module manufacturers.
Module-row distance
approx. 10 mm
RAPIDPRO MODULE C LAMP | V 1 | INSTALLATION GUIDE | 202102
SCHLETTER SOLAR GMBH | SUBJECT TO CHANGES
6
SCHLETTER SOLAR GMBH
4. INSTALLING THE FINAL MODULE
Click in 2 RapidPro end clamps and tighten the screws.
Please ensure that the clamp fits against the module frame (see illustration).
Note on disassembly
To loosen or dismantle the module clamps, please proceed as follows: When loosening
the clamps, pull the upper part of the clamp upwards together with the screw so that the
clamp is loosened from the module frame and the screw does not unscrew from the
upper part of the clamp.
Further information regarding our systems is available on our website:
www.schletter-group.com under Downloads in the solar section.
RAPIDPRO MODULE CLAMP | V1 | INSTALLATION GUIDE | 202102
SCHLETTER SOLAR GMBH | SUBJECT TO CHANGES
0
0
SCHLETTER SOLAR GMBH
Alustrasse 1
83527 Kirchdorf
GERMANY
www.schletter-group.com
We reserve the right to changes, including
technical modification.
Table of contents
Other Schletter Power Tools manuals
