Sanyo PLL405WP-B0X1 User manual
INSTRUCTION MANUAL
PLL405WP-B0X1
40inch Multimedia LCD monitor
with Network-PC
ENGLISH
nWe reserve the right to change specifications without notice.
nAll trademarks used in this user manual are the property of their respective owners.
nThis manual is printed on recycled paper.
FCC DECLARATION OF CONFORMITY
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for Class A Personal Computers and
peripherals, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the device is operated in a residential environment. This device generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. Operation of this device in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at his
own expence.
CAUTION Changes or modifications not expressly approved by manufacturer could void the users
authority to operate the device under FCC compliance regulations.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
CANADIAN NOTICE
CE MARKING DECLARATION OF CONFORMITY
This LCD monitor complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” and 73/23/
EEC “Low Voltage Directive” as amended by Directive 93/68/EEC.
WARNING This is a class A product. In a domestic environment this product may cause radio inter-
ference in which case the user may be required to take adequate measures.
ENGLISH
FOR YOUR SAFETY ................................................................ 1
SAFETY PRECAUTIONS ................................................... 1
SPECIAL NOTES ON LCD MONITORS ............................... 3
CLEANING ......................................................................... 3
BEFORE YOU OPERATE THE MONITOR .................................. 4
FEATURES ......................................................................... 4
CHECKING THE CONTENTS OF THE PACKAGE ............... 4
INSTALLATION .................................................................. 5
CONTROLSAND CONNECTORS ...................................... 6
CONNECTING YOUR MONITOR ........................................ 7
BASIC OPERATION ............................................................ 8
TROUBLE SHOOTING .............................................................. 9
APPENDIX ................................................................................ 10
SPECIFICATIONS ............................................................... 10
DIMENSIONS ...................................................................... 11
CONNECTOR PINASSIGNMENT ........................................ 11
TABLE OF CONTENTS
ENGLISH
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor
and contact your dealer immediately. Further use may be dangerous and can cause fire or electric
shock.
NEVER REMOVE THE CABINET
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of
fire or electric shock.
DO NOT PUT ANY OBJECT INTO THE MONITOR
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug
your monitor immediately and contact your dealer. Using the monitor with any object inside may
cause fire, electric shock or damage.
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
The monitor may cause an injury if it falls or is dropped.
DO NOT USE THE MONITOR NEAR WATER
Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric
shock.
OPERATE UNDER THE SPECIFIED POWER SUPPLY
Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage will
cause malfunction and may cause fire or electric shock.
PROTECT THE CABLES
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy
objects on the cables. If damaged, the cables may cause fire or electric shock.
ADVERSE WEATHER CONDITIONS
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in
power may cause malfunction. It is also advised not to touch the plug in these circumstances as it
may cause electric shock.
FOR YOUR SAFETY
WARNING
SAFETY PRECAUTIONS
1 FOR YOUR SAFETY
ENGLISH
CAUTION
INSTALLATION LOCATION
Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky
areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun
shines directly on the monitor.
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not
place any heavy objects on the monitor, and that all cables are routed such that children may not pull
the cables and possibly cause injury.
MAINTAIN GOOD VENTILATION
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause
fire. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls.
Ventilation slots on the back of the cabinet will be blocked and the monitor may overheat if the stand
is removed. This may cause fire or damage. Operating the monitor on its back, side, upside down or
on a carpet or any other soft material may also cause damage.
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal
cable is disconnected. If you do not disconnect them, it may cause fire or electric shock. It is
recommended that two people are used when moving the monitor.
UNPLUG THE MONITOR
If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid
accidents.
HOLD THE PLUG WHEN DISCONNECTING
To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable itself
as this may cause fire or electric shock.
DO NOT TOUCH THE PLUG WITH WET HANDS
Pulling or inserting the plug with wet hands may cause electric shock.
DO NOT TURN ON AND OFF THE POWER FREQUENCY
Do not alternate between turning the power ON and OFF frequency as it may cause damage.
ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room.
When using the monitor over a prolonged time, a ten minute break every hour is recommended as
looking at the screen continuously can cause eye strain.
OTHERS
FOR YOUR SAFETY 2
ENGLISH
Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image, when the same image is displayed for hours. In
this case, the screen is recovered slowly by changing the image or turning off the
Power Switch for hours. There is the possibility that the previous screen has been
fixed. Pay attention sufficient when you use LCD Monitor.
You may find slightly uneven brightness on the screen depending on the desktop
pattern you use.
Contact your dealer for the backlight replacement when the screen is dark, flickering
or not lighting up. Never attempt to replace it by yourself.
Due to the nature of the backlight, the screen may flicker during initial use. Turn off
the Power Switch and then turn it on again to make sure the flicker disappears.
If you drop any materials or liquids such as water into the monitor when cleaning,
unplug the power cable immediately and contact your dealer.
For safety reasons, turn off the power switch and unplug the monitor before you
clean it.
To protect the LCD panel, do not scratch or rub the screen with a hard object.
Never use any of the following strong solvents. These will damage the cabinet and
the LCD screen.
Thinner
Benzine
Abrasive cleaner
Spray-type cleaner
Wax
Acid or Alkaline solvent
Touching the cabinet with any product made from rubber or plastic for a long time
may cause degeneration or loss of paint on the cabinet.
Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Then
wipe the cabinet with a soft dry cloth.
Periodic cleaning with a soft dry cloth is recommended.
Don't use tissue paper etc. because these will damage the LCD screen.
The following symptoms are normal with LCD monitors and do not indicate a problem.
NOTE When you first turn on the LCD monitor, the picture may not fit in the display area
because of the type of computer that is used. In this case, adjust the picture
position to its correct position.
n
n
n
SPECIAL NOTES ON LCD MONITORS
3 FOR YOR SAFETY
n
n
WARNING n
CAUTION n
NOTE n
n
n
CABINET
LCD
SCREEN
CLEANING
ENGLISH
u39.6” Wide Screen TFT Color LCD Monitor
uSupports Resolutions up to 1280 × 768
uSuper Wide Viewing Angle, High Brightness and High Contrast
uIntegrated PC platform
uLAN interface connection
uOperating System: Windows®Professional
uPivot function is available for portrait screen style mounting
The following accessories are included in your package. Check to see if they are enclosed with the
monitor.
nPower Cable*
nRecovery CD-ROM
nInstruction Manual
nSample: Pivot®software / VIA Driver (CD)
Pivot®: This software enables to rotate the orientation of the screen to display in portrait or
landscape mode.
Consult english.txt in CD-ROM for installation.
CAUTION * Check the rating of the Power Cable enclosed is as follows.
n120V area : 10A/125V
nHigher than 120V area : 10A/250V
CHECKING THE CONTENTS OF THE PACKAGE
BEFORE YOU OPERATE THE MONITOR
BEFORE YOU OPERATE THE MONITOR 4
FEATURES
ENGLISH
5 BEFORE YOU OPERATE THE MONITOR
INSTALLATION
Install the stand on a stable surface. The monitor may cause injury or damage if it
falls or is dropped.
n
CAUTION
n
Unplug the monitor before installation to avoid electric shock or damage.
n
The monitor is heavy. Two person handling is recommended.
n
Do not give a strong impact to the monitor. It may cause damage.
PROCEDURE AND CONDITIONS FOR MONITOR INSTALLATION
AEnvironmental temperature and humidity for installation:
Please be sure that an environmental temperature and humidity DO NOT exceed the range
described in the page 10 SPECIFICATIONS.
BSize of screw
nM6
nLength: After fasten the bracket with screws, the length of screw in the monitor should be
more than 10-15mm.
nPosition: more than 6 points
ATTENTION TO THE PORTRAIT INSTALLATION
For portrait installation, place the panel with rotating it 90 degrees in a counterclockwise
direction.
Placing the panel with rotating it 90 degrees clockwise may cause damage to the screen.
Follow the instructions below when installing the monitor to the wall.
NOTE
ENGLISH
CONTROLS AND CONNECTORS
BHandles
CUSB Connector 2Port ( )
DRS-232C Connector ( COM2 )
ELAN Connector ( )
FSoft Off Button ( )
GBrightness Knob (BRIGHTNESS)
HVolume Knob (VOLUME)
IExternal Speaker Output Terminal (SPEAKER)
JAC Connector (AC IN)
KMain Power Switch (POWER)
<Front>
APower Indicator
<Back>
BEFORE YOU OPERATE THE MONITOR 6
ENGLISH
7 BEFORE YOU OPERATE THE MONITOR
[Example of Connection]
Power Cable (Accessory)
Computer
(Not included)
RS-232C Cable (Not included)
Speaker (Not included)
Speaker Cable (Not included)
LAN Cable (Not included)
Mouse
USB Keyboard
(Not included)
USB Mouse
(Not included)
NOTE nThe signal cables used for connecting the computer and monitor may vary with the type
of computer used. An incorrect connection may cause serious damage to both the
monitor and the computer.
nMake sure you tighten the finger screws at each end of the signal cable.
CONNECTING YOUR MONITOR
AEnsure that both the computer and the monitor are switched off.
BConnect the computer to the monitor with the LAN cable. (See page 11 for CONNECTOR PIN
ASSIGNMENT.)
CConnect the RS-232C cable to the computer while using the RS-232C control feature. (See page
11 for CONNECTOR PIN ASSIGNMENT.)
nThis Serial Port is COM2.
DConnect the monitor to the USB compliant computer with the USB cable when using the USB hub
features. (See page 11 for CONNECTOR PIN ASSIGNMENT.)
EConnect the monitor to the speakers with the Speaker Cable when using the speakers.
nWhen connecting speakers, rating of speaker should be 10W (4W) or equivalent.
FConnect the Power Cable to the monitor first and then to the power supply.
NOTE
NOTE
Table of contents
Other Sanyo Monitor manuals
Sanyo
Sanyo CE52LH1R - 16:9 User manual
Sanyo
Sanyo VMC-8521P User manual
Sanyo
Sanyo VMC-8613B User manual
Sanyo
Sanyo PID-42AE1 - 16:9 User manual
Sanyo
Sanyo PDP-32H1ENV User manual
Sanyo
Sanyo CE42LM5R User manual
Sanyo
Sanyo AVL-3210 User manual
Sanyo
Sanyo CE20LM5 User manual
Sanyo
Sanyo CE42LM4N-NA - CE - 42" LCD Flat Panel... User manual
Sanyo
Sanyo VM-6609PA User manual
Sanyo
Sanyo CE42LM5WP User manual
Sanyo
Sanyo C-15LP1A User manual
Sanyo
Sanyo PID-42AE1 - 16:9 User manual
Sanyo
Sanyo VMC-L2017 User manual
Sanyo
Sanyo VM-6609 User manual
Sanyo
Sanyo CE42LM4R-E User manual
Sanyo
Sanyo VMC-8415FP User manual
Sanyo
Sanyo CE42SR1 User manual
Sanyo
Sanyo CE42SRE1 User manual
Sanyo
Sanyo VRM-30 User manual
