S&T TPMS1209T02-ER User manual
Page 1 of 28
TPMS1209T02-ER
USER MANUAL
Suzhou Sate Auto Electronic Co., Ltd
www.sate.com.cn
Page 2 of 28
Table of Contents
I. TPMS1209T02-ER, Full-time Direct TPMS
-----------------------------------3
II. Parts of TPMS1209T02-ER
--------------------------------------------------------3
III. Installation and Programming of TPMS1209T02-ER Monitor
---------4
1. Installation of Monitor
-----------------------------------------------------------4
2. Programming of Monitor
-------------------------------------------------------5
2.1Programming of Transmitter ID
-----------------------------------------7
2.2 Standard Pressure Programming
----------------------------------------7
2.3 System Time Programming
---------------------------------------------- 9
2.4 Programming of Pressure Unit
-----------------------------------------11
2.5 Deletion of Transmitter ID
-----------------------------------------------12
IV. Installation of TPMS1209T02-ER Transmitter
-------------------------------12
1. Installation of Transmitter
---------------------------------------------------------13
2. Installation of Security Lock
-----------------------------------------------------14
V. System Function of TPMS1209T02-ER
---------------------------------------17
1. Full-time Monitoring
--------------------------------------------------------------17
2. High Pressure Alarm
---------------------------------------------------------------17
3. Low pressure level 1 alarm
------------------------------------------------------18
4. Low pressure level 2 alarm
-------------------------------------------------------18
5. Low pressure level 3 alarm
-------------------------------------------------------19
6. High Temperature Alarm
----------------------------------------------------------19
7. Quick Leak Alarm
-------------------------------------------------------------------20
8. Transmitter Trouble Alarm
--------------------------------------------------------21
VI. TPMS1209T02-ER Auxiliary Functions in Normal Mode
---------------21
Alarm Record Inquiry
------------------------------------------------------------------21
VII. Specifications
-------------------------------------------------------------------------24
VIII. Frequently Asked Questions
----------------------------------------------------25
IX. Warranty Term
-------------------------------------------------------------------------27
X. Important Notes
------------------------------------------------------------------------28
Page 3 of 28
I. TPMS1209T02-ER, FULL-TIME DIRECT TPMS
TPMS1209T02-ER is direct tire pressure monitoring system for trucks
which includes 1 monitor, 1 standard booster and 2 to 38 transmitters and
it can support monitoring of up to 38 tires. The transmitter can be
screwed onto the tire instead of the valve cap and then senses the pressure
inside the tire all the time and transmits the pressure information data to
the booster by RF technology. Then the booster transmits the pressure
information data to the monitor after received and magnified it. The
monitor can receive and deal with the data, then display the pressure on
the screen. The monitor can issue different alarms if the tire pressure is at
an improper level based on the standard pressure, so as to notify the
driver to treat the problem and avoid tire busting or tire damage.
Through TPMS1209T02-ER, the driver can keep the tire running under a
proper pressure so as to avoid excess gasoline consumption and keep the
vehicle in an easily controlled state.
II. Parts of TPMS1209T02-ER
1 Monitor
6 Transmitters
6 Security Locks
1 Bracket
2 Wrenches
4 3M Dual Lock
1 User Manual
1 Standard Booster (optional)
Page 4 of 28
Monitor
Transmitter
III. Installation and Programming
of TPMS1209T02-ER
1. Installation of Monitor
1.1 Insert the pedestal to the back of the monitor as shown in below
picture.
1.2 Choose a suitable location to install the Monitor onto the dashboard.
Make sure to first scrub the surface of the location with alcohol. Next,
strip off the liner of the 3M Dual Lock Fastener, put the sticky side
onto the suitable location, then fix the Monitor with another side of
the 3M Dual Lock Fastener on the platform.
Install Pedestal
LCD
Screen
Key
Alarm Lamp
Pedestal
Transmitter
Security Lock
Wrench
Page 5 of 28
1.3 The monitor power wire consists of 3 different colors of wires. The
Black wire should be connected to the ground. The Red wire should
be connected to the vehicle’s continuous power supply. The Blue wire
should be connected to ignition switch, when switched to “ON”, the
blue wire is connected with 12V power.
The monitor starts to work after it is powered. At this time the monitor
cannot receive any information as the transmitters are not installed. The
screen shows “NSP”, which means there are “No Transmitters
Programmed”.
2 Programming of Monitor
Through the monitor, the user can program up to 38 transmitters ID
number and the standard pressure for each wheel. Operation steps are as
following:
3M Dual Lock
Page 6 of 28
2.1 Programming of Transmitter ID
When the monitor is powered for the first time, the screen shows
“NSP”, which means there is no transmitter programmed into it. If the
user wants to program a new transmitter into the monitor, the operation
should be finished in programming mode. At this time, make sure the
transmitter to be programmed has not been screwed onto the valve cap
yet until the programming has been finished and the monitor returns to
normal mode.
Each transmitter has 4 groups of ID, for example when program the
transmitter with ID of 001 001 001 158 to front right tire position, the
user only needs to input the last 3 digits “158”. Monitor will record the
rest 3 groups of ID automatically.
1. After monitor is powered, the screen will display “NSP”, then press P
for 3 seconds to access the system programming mode, the first
interface is for ID programming as shown below:
2. Press any of the four arrow keys to choose the transmitter position
which needs to be programmed.
3. Then press S for 3 seconds to start programming and the digit flashes,
Page 7 of 28
then press up or down arrow key to adjust the value.
4. Once finish programming of the first digit, press →to start
programming the second digit which flashes. Press up or down arrow
key to adjust the value.
5. Press →again to program the third digit which flashes. Press up or
down arrow key to adjust the value.
6. When finish programming these 3 digits, press S for 3 seconds to save
with the screen flashes twice, beep buzzes twice. Then it will
automatically switch to next tire position.
7. Follow the above operations to program ID of other transmitters.
2.2 Standard Pressure Programming
For example, set the standard pressure of front right tire to 105 psi:
1. When finish programming ID, press P to access the standard pressure
Page 8 of 28
programming mode.
2. Then press any of the four arrow keys to choose the desired tire
position.
3. Then press S for 3 seconds to set the first digit which flashes. Press up
or down arrow key to adjust the value to 1.
4. Once finished programming the first number, press →to program
the second digit which flashes and then press up or down arrow key to
adjust the value to 0.
5. Once finished programming the second number, press
→to
program the third
digit which flashes and then press up or down arrow
key to adjust the value to 5. Then press S for 3 seconds to save with the
screen flashes twice, beep buzzes twice.
Page 9 of 28
Note: The default standard pressure is set to 100 psi in factory.
2.3 System Time Programming
Function: The system clock was preset in the factory. It is the base of
the alarm record, user can check the current date and time as
follows:
1. When finish programming the standard pressure, press P to access
interface for inquiry and programming of time/date, the first
interface displays the year, 1 07 stands for the year 2007:
2. Press ↓key to access the second interface, 211 stands for November
as shown below:
Page 10 of 28
3. Press the ↓key to access the third interface, 312 stands for 12th day
as shown below:
4. Press the ↓key to access the fourth interface, 416 stands for 16
O’clock as shown below:
5. Press the ↓key to access the fifth interface, 533 stands for 33 mins.
As shown below:
Under any interface of system time inquiry, press S for 3 seconds to
start programming. For example change the year to “09”, under the
year interface, press S for 3 seconds, the second digit flashes, press up
or down arrow key to adjust the value. Then press →key, the third
number flashes, then press the up or down arrow key to adjust the value
to“9”. At last press S for 3 seconds to save the change with screen
flashes twice and beep buzzes twice. Then it automatically switches to
Table of contents
Other S&T Computer Hardware manuals
S&T
S&T kontron KBox E-420-R1K/V1K User manual
S&T
S&T Kontron CP3005 Series User manual
S&T
S&T Kontron COMe-cTL6 User manual
S&T
S&T Kontron SL iMX8MM User manual
S&T
S&T kontron COMe-cWL6 User manual
S&T
S&T Kontron OSM-S i.MX8M Mini User manual
S&T
S&T Kontron SMARC-sXEL User manual
S&T
S&T kontron COMe-bV26 User manual
S&T
S&T Kontron VX3060 User manual
S&T
S&T kontron COMe-cEL6 User manual
Popular Computer Hardware manuals by other brands
EMC2
EMC2 VNX Series Hardware Information Guide
Panasonic
Panasonic DV0PM20105 Operation manual
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 user manual
Gigabyte
Gigabyte B660M DS3H AX DDR4 user manual
Raidon
Raidon iT2300 Quick installation guide
National Instruments
National Instruments PXI-8186 user manual
