Samsung SCH-LC11 User manual
User manual
SCH-LC11
introducing your mobile device
In this section, learn about your mobile device’s layout, keys, display, and icons
Unpack
Check your product box for the following items:
Mobile device
Battery
Travel adapter (charger)
User manual
The items supplied with your device may vary depending on the software and accessories available in your region or
offered by your service provider. You can obtain additional accessories from your local Samsung dealer.
Device layout
The front of your device includes the following keys and features:
The rear of your device includes the following keys and features:
Keys
Key Function
Power Turn the device on and off (press and hold);
Side keys Short press of the side key will help you set up your
device automatically. Long press of the side key will reset
the status of your device as the state of the factory
LED indicators
Your device’s LED indicators consist of four LEDs:
LED Display
LED 1 LTE Network Status (including the signal strength)
LED 2 1x / EVDO Network Status (including the signal strength)
LED 3 WiFi & Internet Status
LED 4 Power & Charging
Power & Charging Status Indication
Scenario LED 1 LED 2 LED 3 LED 4 Comments
TA
not
connected
Power Off / No
Battery [X][X][X][X]ㅡNo light
Power On [X][X][X][B]
ㅡLED4 : Blue - Solid
ㅡmeans a remained battery
capacity of 100~20%
Low Battery [X][X][X][Y]
ㅡLED4 : Yellow - Solid
ㅡmeans a remained battery
capacity of 20~6%
Critical Low
Battery [X][X][X][R]
ㅡLED4 : Red - Solid
ㅡmeans a remained battery
capacity of 5~1%
TA
connected
Charging [X][X][X][G]
- Blinking -
ㅡLED4 : Green - Blinking
Charging Error [X][X][X][R]
- Blinking -
ㅡLED4 : Red - Blinking
Fully Charged [X][X][X][G]ㅡLED4 : Green - Solid
LTE Network Service Indication
Scenario LED 1 LED 2 LED 3 LED 4 Comments
LTE_Strong / Modest RF
Signal [B][X][X][B]
ㅡLED1 : Blue - Solid
ㅡStrong RF signals, meaning to
2~4 Antenna Bars
LTE_Weak RF Signal [Y][X][X][B]
ㅡLED1 : Yellow - Solid
ㅡWeak RF signals, meaning 1
Antenna Bar
LTE_Critical Weak RF &
No Service [R][X][X][B]
ㅡLED1 : Red - Solid
ㅡAntenna Icon Only & No Service
LTE Service Roaming [W][X][X][B]ㅡLED1 : White - Solid
LTE Service Failure [R]
- Blinking -[X][X][B]ㅡLED1 : Red - Blinking
No WAN Connection [X][X][X][B]ㅡLED1 : No light
1x / EVDO Network Service Indication
LTE EV
1x
Scenario LED 1 LED 2 LED 3 LED 4 Comments
1x / EVDO_Strong /
Modest RF Signal [X][B][X][B]
ㅡLED2 : Blue - Solid
ㅡStrong RF signals, meaning to
2~4 Antenna Bars
1x / EVDO_Weak RF
Signal [X][Y][X][B]
ㅡLED2 : Yellow - Solid
ㅡWeak RF signals, meaning 1
Antenna Bar
1x / EVDO_Critical Weak
RF & No Service [X][R][X][B]
ㅡLED2 : Red - Solid
ㅡAntenna Icon Only & No Service
1x / EVDO Service
Roaming [X][W][X][B]ㅡLED2 : White - Solid
1x / EVDO Service Failure [X][R]
- Blinking -[X][B]ㅡLED2 : Red - Blinking
No WAN Connection [X][X][X][B]ㅡLED2 : No light
WiFi & Internet Status Indication
Scenario LED 1 LED 2 LED 3 LED 4 Comments
WiFi Standby
(No WLAN connection & No
WiFi connected) [X][X][G][B]ㅡLED3 : Green - Solid
WiFi Connected
(WiFi connected but no data
transfer) [X][X][B][B]ㅡLED2 : Blue - Solid
Data Transfer [X][X]
[B]
- Blinking
in proportion to
data rate -
[B]
ㅡLED2 : Blue - Blinking
ㅡBlinking rates depends on the
data transfer rates
Combined Indication
Scenario LED 1 LED 2 LED 3 LED 4 Comments
OTADM Downloading and
Updating [B]
- Blinking
→
[B]
→
Blinking
→
[B]
→
Blinking -[B]
ㅡLED1, LED2, LED3 : Blue -
Blinking Sequentially
No SIM [W][W][W][B]
ㅡLED1, LED2, LED3 : White -
Solid
assembling and preparing your mobile
device
Get started by assembling and setting up
your mobile device for its first use.
Install the SIM card and battery
When you subscribe to a cellular service, you will receive a Subscriber Identity Module, or SIM card, with subscription details,
such as your personal identification number (PIN) and optional services.
To install the SIM card and battery,
1. Remove the battery cover. If the device is on, press and hold [ ] to turn it off.
2. Insert the SIM card. Place the SIM card in the device with the gold-coloured contacts facing down.
3. Insert the battery.
4. Replace the battery cover.
Charge the battery
Before using the device for the first time, you must charge the battery.
1. Open the cover to the multifunction jack on the side of the device.
2. Plug the small end of the travel adapter into the multifunction jack. Improperly connecting the travel adapter can cause
serious damage to the device. Any damages by misuse are not covered by the warranty.
3. Plug the large end of the travel adapter into a power outlet.
4. When the battery is fully charged (the [|||||] icon is no longer moving), unplug the travel adapter from the power outlet.
5. Unplug the travel adapter from the device.
6. Close the cover to the multifunction jack.
About the low battery indicator
When your battery is low, the device will change its LED color from green to yellowr. If the battery level becomes too low, it will
show red colors and the device will automatically power off. Recharge your battery to continue using your device.
Other manuals for SCH-LC11
4
Table of contents
Other Samsung Network Router manuals
Samsung
Samsung Ubigate iBG2016 Programming manual
Samsung
Samsung Connect Home Pro ET-WV533 User manual
Samsung
Samsung DCS-VIP User manual
Samsung
Samsung Ubigate iBG2006 User manual
Samsung
Samsung DIR-640LA1 User manual
Samsung
Samsung iES4028FP User manual
Samsung
Samsung OFFICESERV 500 Series User manual
Samsung
Samsung Ubigate iBG1000 User manual
Samsung
Samsung Ubigate iBG1003 User manual
Samsung
Samsung iES4028F Programming manual
Samsung
Samsung iES4028FP User manual
Samsung
Samsung MWR-SH00N User manual
Samsung
Samsung DCS-Compact II User manual
Samsung
Samsung Connect Home Pro ET-WV531 User manual
Samsung
Samsung Techwin SPN-10050 User manual
Samsung
Samsung AHT-E300 User manual
Samsung
Samsung Connect Home Pro ET-WV532 User manual
Samsung
Samsung SCC-RC130 User manual
Samsung
Samsung MagicLAN SWL-2200U User manual
Samsung
Samsung 5G CPE User manual
