Salini SCC-5925B Manual

CERAMIC COOKTOP

User Manual & Installation Instructions

SCC-5925B

WWW.SALINI.COM.AU

TABLE OF CONTENTS

IMPORTANT SAFETY INFORMATION

INSTALLATION

USING YOUR APPLIANCE

CLEANING & MAINTENANCE

TROUBLESHOOTING

TECHNICAL DATA & SPECIFICATION

DECLARATION OF CONFORMITY

4-5

6-7

8-12

Installation of the appliance must only be undertaken by a licensed electrician.

This manual contains important information including safety, operational & installation information

which will enable you to get the most out of your appliance. Please keep it in a safe place so that it

is easily available for future reference; for you or any person not familiar with the operation of the

appliance.

IMPORTANT SAFETY INFORMATION

IMPORTANT INFORMATION

WARNING AND SAFETY INSTRUCTIONS

• Carefully read the following important information regarding installation safety and maintenance.

• Keep this information booklet accessible for further consultations.

• This appliance is designed for domestic household use and is designed to be built into a standard

kitchen cabinet benchtop or housing unit. For indoor use only.

• IMPORTANT: Your product warranty will be void if the installation is not in accordance with the

instructions. The installation must be carried out by a suitably qualied person, in accordance

with the manufacturer’s instructions, and must be connected in accordance with all applicable

electrical regulations.

• The use of this appliance for any other purpose or in any other environment will void warranty.

• This appliance is designed to cook and heat up food on suitable pots or pans, any other use will

be deemed improper use. The manufacturer declines all responsibility for improper use.

• Your new appliance is guaranteed against electrical or mechanical defects, subject to certain

exclusions, the foregoing does not aect your statutory rights.

• Repairs may only be carried out by service engineers or an authorised service agent.

• Check the appliance for damage after unpacking it. Do not connect or install the appliance if it

has been damaged in transport as this will void the warranty.

• The manufacturer declines all responsibility for damage to persons or property caused by

non-observance of the information outlined in this manual or by interference with any part of the

appliance or by the use of non-original spare parts.

• We recommend you review the troubleshooting information before calling a technician.

• Information, specications and recommendations can change without notice.

• WARNING: Accessible parts may become hot during use, and retain heat after operation. Care

should be taken to avoid touching heating elements and surrounds. While in operation, direct

contact with the hob or ames may cause burns.

• All installation work must be carried out by a qualied electrician.

• This appliance complies with all current Australian and European safety legislation, and designed

to operate safely in normal indoor domestic use.

• Appliance shall only be used with rated voltage and frequency 220/240v, 50Hz.

• Before installation and usage, read all the instructions and make sure that the voltage (V) and the

frequency (Hz) indicated on your appliance data plate are exactly the same as the voltage (V) and

the frequency (Hz) in your home.

WARNING! Proper use and safety precautions are as follows.

All instructions must be read and understood before use.

• WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in re.

• Do not leave frying pans unattended during use.

• Never try to extinguish a re with water, instead switch o the appliance if possible, then cover

ame e.g. with a lid or a re blanket.

• CAUTION: The cooking process has to be supervised. A short term cooking process has to be

supervised continuously.

• WARNING: Danger of re: do not store items on cooking surfaces.

• Do not place objects made of metal such as knives, forks, spoons and saucepan lids on the cook-

ing surface as they can get hot.

• Switch each cooking zone o after each use. When you have nished using the appliance double

check that all the controls are in the o or closed position.

• WARNING: If the surface is cracked, switch o the appliance to avoid the possibility of electric

shock. If the appliance is damaged or faulty do not attempt to use.

• There is a re risk if cleaning is not carried out in accordance with the instructions.

• Do not use a steam cleaner on appliance.

• Children should be supervised to ensure that they do not play with the appliance.

• Cleaning and user maintenance shall not be made by children without supervision.

• This appliance is not intended for use by persons (including children) with reduced physical, sen-

sory or mental capabilities, or lack of experience and knowledge, unless they have been given su-

pervision or instruction concerning use of the appliance by a person responsible for their safety.

• Disconnect the electrical plug prior to any maintenance or cleaning.

• Cleaning should be carried out in accordance with the“Cleaning and Maintenance” section to

avoid possible hazards.

• Never unplug appliance by pulling on the cable.

• Do not disconnect the appliance with wet hands or force the supply cord.

• If the power cord is damaged it must be replaced by the manufacturer or a qualied service

engineer to avoid any electrical hazards.

• WARNING: Use only hob guards designed by the manufacturer of the cooking appliance or indi-

cated by the manufacturer of the appliance in the instructions for use as suitable or hob guards

incorporated in the appliance. The use of inappropriate guards can cause accidents.

• This appliance is not intended to be operated by means of an external timer or separate re-

mote-control system.

• In the event of any incident caused by a technical fault, disconnect the power and report the fault

to be repaired before use.

• Before rst use, carry out a brief inspection test of the appliance, should the appliance not

function, disconnect it from the power supply and call the installer or an authorised service agent.

CAUTION! Cleaning operations must only be carried out when the appliance

is cool and disconnected from the power supply.

It is a requirement for the electrical system to be grounded according to the methods required by

the applicable regulations. Before the appliance is connected with the mains, assemble one full polar

breaker with over 3mm opened on the mains, and the rated current of the breaker is strongly recom-

mended over 40A. Please oer the power wire, which is up to the mustard (3*4 mm2), and let expert

install it in accordance with the gure shown.

Connect ground (yellow/green

one) to the place of ground mark; L

(brown one) to the place of ve-foot

plug; N (blue one) to the place of

four-foot plug.

If a plug and socket are being used

make sure that they are compatible,

and are connected by means of a

power cable that complies to the

applicable regulations. The socket

must be accessible after the hob is

built in. Avoid the use of adapters

and shunts as these could cause

overheating and risk of re.

If a xed connection is being used, t power line with an omnipolar circuit breaker with a contact

opening gap equal to or greater that 3mm in an easily accessible position in proximity to the cooktop.

If the appliance you have purchased is not tted with a mains power lead. A power lead resistant to a

temperature of at least 90°C must be used. Otherwise, the electrical safety of the appliance may be put

at risk.

On rst connection to the electrical mains, an operating check will be carried out automatically and

all the indicator lights will come on for a few seconds. Immediately after installation, carry out a brief

WARNING! This product must be installed by a licensed electrician.

INSTALLATION

• Any work on electric equipment and systems may only be carried out by a qualied electrician.

• Installer or qualied technician must carry out inspection and testing of the installed appliance.

• Means for disconnection must be incorporated in the xed wiring, in accordance with the wiring

rules.

• Means for disconnection incorporated in the xed wiring is in accordance with AS/NZS 3000

• WARNING: Always switch o the electricity supply at the mains during installation and during

maintenance to avoid the possibility of electric shock.

• Before installation, read all the instructions and make sure that the voltage (V) and the

frequency (Hz) indicated on your appliance data plate are exactly the same as the voltage (V) and

the frequency (Hz) in the system.

• Electrical data plate can be found on underside of appliance (Do not remove).

ELECTRICAL CONNECTION

SETTING POSITION

The preparation of the benchtop and cabinet

for installation of the cooktop requires some

carpentry and cabinetry work, this work must

be carried out by a competent tradesperson.

Use the product to create the cut-out into the

benchtop to mount the cooktop, ensure all

required distances are observed see “SETTING

POSITION” section.

The cabinet hole and cut out dimensions listed

in this document are to be used as a guide only,

it is essential to refer to the actual cooktop

before making any cuts.

When mounting the cooktop, ensure the

power supply positioned so that it does not

make contact with the bottom of the casing of

the appliance or oven installed underneath (if

applicable).

The cooktop is to be installed into an appropriate bench top and cabinet. The benchtop material and

the cabinet surrounds should be heat resistant for at least 90°C.

The minimum distances that should be observed:

Cooktop to back wall 50 mm

Cooktop to side wall 50 mm

Cooktop to any cabinets above 750 mm

Cabinet void underneath 200 mm

When installing cooktop with a cupboard underneath,

there must be a dividing shelf installed with a void that is a

minimum of 200mm from the bottom of the appliance and

the top of the dividing shelf. In the case where the cooktop

will be installed over an oven, this void is not required. When

installing above an oven, the oven must be equipped with a

cooking fan to prevent overheating.

The cooktop must not be installed above a built in dishwasher.

PREPARING CABINET & BENCHTOP FOR INSTALLATION

WARNING: Do not attempt to repair the appliance. Service and repair

should only be attempted by a suitably qualied and authorised agent.

inspection and test the cooktop following the instructions for use. If the cooktop fails to operate,

recheck the installation and ensure that the instructions have been followed. If it cannot be operated

correctly, disconnect the appliance from the electrical mains and contact the service center.

min 200mm

min

120mm

USING YOUR APPLIANCE

COMPONENTS OVERVIEW

COOKING ZONES

The cooktop features a range of dierent sized and powered cooking zones. Below is a list of the zones

and their descriptions and power output.

CONTROL PANEL

The cooktop controls are grouped together on the front panel. To operate the touch-control buttons,

lightly press the icons printed on its surface. Below is a list of the buttons and their function.

Power on & o

Timer

Increase

Decrease

Pause & continue

Lock out function

Rear left zone selection

Front left zone selection

Center zone selection

Rear right zone selection

Front right zone selection

ASingle cooking zone 1200W

B Single cooking zone 1800W

E Dual round cooking zone 700\1700W

GDual round cooking zone 1200\2400W

INSTRUCTIONS FOR USE

WARNING! When the burners or plates are in use do not leave them unattended.

• Before use, operators must read and understand the manual safety cautions.

• When the appliance is in use, ensure children are supervised at all times.

• When cooking, always check that pan handles are positioned out of reach for children.

• Always inspect before use. If you see any cracks on the surface of the plate, do not use, disconnect

the appliance from the mains immediately and contact a service agent.

• After you have used the appliance make sure that all the controls are o or closed.

The burners are graduated in their size and rating to designed to provide the exact heat required for

every style of cooking, appropriate sized cookware should be used according to cooking zone size.

There are indicator lights to show which burner or heating element is in operation. When you have

nished using each cooking zone, they should be turned o. Extra care should be observed at the end

of use to ensure that the zones are correctly switched o.

During cooking, ensure all other household equipment and materials do not touch the cooktop, as the

insulation material of this equipment is usually not resistant to high temperatures.

Warning lights indicating residual heat my not be visible to children. Even after the appliance has been

turned o, the cooking zone remains hot for a certain period of time. Make sure that children never

touch the appliance.

BEFORE FIRST USE

Before cooking for the rst time, ensure all packaging is removed from the appliance. Then clean the

appliance surface and surrounds to ensure there is no debris remaining from the installation.

We recommend running an initial operation cycle to remove any surface chemicals and to evaporate

any humidity left from the manufacturing process. It is perfectly normal for a smell to be produced

during this process, ensure that the room is well ventilated.

First place a saucepan of water on each of the front hotplates and turn them on full for at least 30mins

before turning o the front zones. Then place the saucepans on the rear and center zones and turn on

for at least 30mins and then turn them o.

NOTE: If the controls do not work properly after the initial operation cycle, it may be that not all the

humidity has evaporated. In this case repeat the cycle until all of the humidity has been evaporated.

CAUTION! The packaging materials can be dangerous for children. Dispose of

packing materials properly to avoid choking hazards.

INSTRUCTIONS FOR USE

SWITCHING ON THE COOKTOP

The cooktop is equipped with touch-control buttons, to operate the buttons lightly press on the icons

printed on the glass surface. When a button is pressed an audible indicator will beep to conrm the

button has been pressed. Refer to the ‘COMPONENTS OVERVIEW’ section for button details.

INSTRUCTIONS FOR USE

When the appliance is not in use, all components and indicator lights will be switched o. To turn the

cooktop on, hold down power key for 2 seconds. An LED indicator will turn on above the symbol

to conrm that the appliance has been turned on. If no functions are selected within 10 seconds of

switching it on, as a precaution it will automatically turn o.

TURNING ON AND SETTING POWER TO THE SINGLE COOKING ZONES

After turning on the appliance, you must choose to ignite a cooking zone within the rst 10 seconds, or

the cooktop will automatically turn o. Choose the cooking zone to turn on by selecting the corre-

sponding zone selection button refer to the‘CONTROL PANEL’ descriptions in the ‘COMPONENTS

OVERVIEW’ section. Then ignite the cooking zone by setting the power. Each zone has a power setting

indicated between 0-9, when the increase or decrease button is pushed the power will

increase or decrease by 1.

To turn o a cooking zone, lower the power to 0 by selecting the zone then lowering power

by pressing until it shows 0. After 5 seconds the cooking zone will automatically switch o. The

cooking zones will still have residual heat and there will be a ashing indicator to warn that they

are still hot.

TURNING ON AND SETTING POWER TO THE DUEL COOKING ZONES

The duel cooking zones are marked with a double ring outline on the cooking zone. They are operat-

ed in the same method as the single cooking zones, except they have the option to use the single or

double burner within the duel zone, refer to the ‘COOKING ZONES’ information in the‘COMPONENTS

OVERVIEW’ section to determine the power for each zone.

To activate the duel cooking zones with only one of the burners, you can select the zone in the same

way you would for a singe zone, by pressing the corresponding zone selection button once before

setting the power. One LED light indicator will show next to the zone selection button to indicate the

cooking zone is using a single burner . To set the duel cooking zone to use both burners, you must

press the zone selection button twice before setting the power. Two LED indicator lights will show next

to the zone selection button to indicate the cooking zone is using the double burner.

To turn o a cooking zone, lower the power to 0 by selecting the zone then lowering power

by pressing until it shows 0. After 5 seconds the cooking zone will automatically switch o. The

cooking zones will still have residual heat and there will be a ashing indicator to warn that they

are still hot.

TURNING OFF THE COOKING ZONES

To turn o a cooking zone, lower the power to 0. After 5 seconds the cooking zone will automatically

switch o. The cooking zones will still have residual heat and there will be a ashing indicator to

warn that they are still hot.

Table of contents

Other Salini Cooktop manuals

Salini

Salini SCI-4052B User manual

Popular Cooktop manuals by other brands

Bonnet

Bonnet OPTIMUM 700 Technical instructions

Jenn-Air

Jenn-Air JGCP430 installation instructions

Frigidaire

Frigidaire FES367FCC Wiring diagram

Ztove

Ztove EZ2 DUO instruction manual

Kleenmaid

Kleenmaid cooking GCTK9011 Instructions for use and warranty details

Casselin

Casselin CSASRE24 manual

Jenn-Air

Jenn-Air JGC2536EB00 Use & care guide

Waldorf

Waldorf RN8603E-B Technical data sheet

Whirlpool

Whirlpool SMP658CNEIXL quick guide

Wolf

Wolf CI243C/B Use and care guide

Fulgor Milano

Fulgor Milano F5PGK305S1 installation instructions

GE JP389 Specifications

Wells

Wells WV-2HFG owner's manual

IKEA

IKEA Lagan HGA4K user manual

Samsung

Samsung NA36N9755 installation manual

Miele

Miele KM 404 operating instructions

Lacor

Lacor 69562 Instructions for use and maintenance

Keating Of Chicago

Keating Of Chicago MG-2 manual