SAFERACKS Bin Rack User manual
S
afe
R
acks
®
©2021Copyright Eagle
Industrial Group Inc.
US Patents D553,401 / 7,357,262 /
D697,785 / 7,152,145. Other Patents
Pending.
Limited Lifetime Warranty U.S. Only.
If you have any questions, please visit our
website or give us a call at:
877-655-3443
www.SafeRacks.com
WARNING:
This product can expose you to
chemicals including lead, which is
known to the State of California to cause
cancer and birth defects or other
reproductive harm. For more
information, go to:
www.P65Warnings.ca.gov.
Bin Rack - Assembly Instructions
Components:
Upper Post (x4)
Lower Post (x4)
Upper/Lower Shelf (x2)
Sliding Rail (x6) Tie Support (x1)
Top Cap (x4) Threaded Insert (x4)
Sleeve Pair (x22) Threaded Foot (x4)
Bins NOT Included
Holds 50lb
Cable Tie
Base (x2)
Drywall
Anchor &
Screw (x2)
Cable Tie (x2)
*Screwdriver required - not included
Per Bin!
S
afe
R
acks
®
Connect sleeve pairs to the notches
above those in Step 2 and ensure they
are of equal height. Place sliding rails on
each side and secure to a snug fit.
Connect sleeve pairs to the next set of
notches. Slide tie support over and
secure to a snug fit. (Note: The two
notches at the top of the lower-front
posts are not used.)
Attach upper posts to lower posts using
the threaded insert. (Note: This step can
be skipped if you have already assembled
the posts.)
Connect sleeve pairs to the marked
notches near the middle of the upper
posts. Place sliding rails on each side and
secure to a snug fit. Repeat for remaining
sliding rails.
Connect sleeve pairs to the top of each
post and ensure they are of equal height.
Slide upper shelf over and secure to a
snug fit.
NOTE: This product holds 50 lbs per bin. Store heavier bins towards the bottom, and never
load a bin with more weight that you can safely raise above your head. Our design is for use
with 27 gallon bins only. Do not use with anything other than 27 gallon bins. Ensure the
sides of the bin are properly secured before sliding in and out.
*Position sleeves slightly
above the notch, then
compress and lower until
secured to desired notch.
1. 2. 3. 4.
5. 6. 7. 8.
Connect sleeve pairs to the lowest notch
on each post. Slide lower shelf over post
and secure to a snug fit. (Note: A rubber
mallet can be used to ensure the shelf is
tight.
Before you begin, you may choose to
assemble the posts fully, but this is not
required. These instructions show the
post assembly in Step 5.
Upper
Post
Lower
Post
Threaded
Insert
Top
Cap
Threaded
Foot
21 11/16”
A. To secure your rack against a wall, drive the
plastic drywall anchor until the anchor is flush
against the wall. Secure the cable tie base to the
wall by inserting the metal screw into the
plastic anchor and tightening. Do not over
tighten.
B. Repeat the steps above ensuring that the
center-center distance is 21 11/16”. Once both
mounts are secured, use the provided cable ties
to secure the rear vertical posts to the wall.
1. 2.
Other SAFERACKS Rack & Stand manuals
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
