SAFECONTROL Touch-101-L User manual
LAN
12/24VDC
SAFECONTROL s. r. o.
Vaníčkova 315/7
169 00 Praha 6
IČO: 02084287
DIČ: CZ02084287
support@safecontrol.cz
www.safecontrol.cz
Touch-101-L
Installation guide
Mounting
Connection
1
Connect the supply voltage to the pa-
nel using the supplied DC connector.
2
Made in Czech Republic
Connect the Ethernet cable
to the ETH port.
1
2
Prepare a hole of the size
256 x 174 mm.
1
4x
4x
1
Information for users on the disposal of electrical and electronic equipment
(corporate and enterprise use)
For proper disposal of electrical and electronic equipment, request detailed
information from your dealer or suppliers.
Information for users on the disposal of electrical and electronic equipment
in other countries outside the European Union
The below symbol is only valid in the countries of the European Union. For proper
disposal of electrical and For detailed information, contact your local authorities
or equipment retailer.
Secure the panel with
screws and struts.
Panel with a sheet thickness
of max. 2.5 mm.
2
1
2
256 mm
174 mm
1
3
3
3
Device settings Reset the device
to default parameters
LTE
WiFi
To work with WEBserver, you need to have the current version
of Google Chrome installed.
1. Set the IP address from the range 192.168.1.0/24 on the PC network
interface, e.g. 192.168.1.101.
2. Open Google Chrome and enter the URL 192.168.1.250.
3. Enter the credentials: user admin, password admin.
4. After logging in, it is necessary to agree to the license conditions
and confi rm them by changing the password.
Setting a new IP address:
1. Go to the Hardware settings page.
2. In the Network settings section, click Edit.
3. Use the fi gure to select the correct network topology.
4. Fill in the required network parameters.
5. Click Save.
6. Edit the IP address on the network interface of your PC to the new
range.
7. Change the URL in the browser to the new IP address of WEBserver.
The device has the following default settings:
• IP address on LAN port 192.168.1.250, mask: 255.255.255.0
• Username: admin
• Password: admin
1. Connect the device to the power supply.
2. Wait for the device to start up safely (2–3 minutes).
3. Using a plastic tool, quickly press the reset button 5 times.
Maximum within 3 s.
4. The device is set to the default settings.
5. If everything went well, the device should not turn itself off .
Note: The process of setting the default settings is performed only by
setting up the network settings and the admin user. No data or other
settings will be deleted from the device by this process.
To connect via LTE/GSM networks, it is necessary to connect
the LTE modem to the USB port. See the online documentation
for supported LTE modems.
1. Make sure the PIN code protection is turned off on the SIM card.
2. Connect the LTE modem with the inserted SIM card to the USB port.
3. No further settings are required, the system automatically adjusts
the network confi guration.
4. In the Hardware settings section, check the connection status
and signal strength..
To connect via WiFi.
1. Go to the Hardware settings section.
2. In the Network settings section, click Edit.
3. Enable WiFi at the bottom.
4. Save the network settings.
5. Click Edit Network Parameters again.
6. Enter the SSID and password or click to Find WiFi network.
Click on the found network and enter the password.
7. Save network settings.
8. Check connection status and signal strength.
3
Enter pin code.
123
456
789
REF 0
Setup
SA VE
Home page
settings
Click here and enter the pin
code “1066“.
Set the target address at the format
below: http(s)://192.168.10.250/display.
Select http or https according to
the server. If you use it in conjunction with
the SAFECONTROL WEBserver, write
after the address/display for registration
to automatically log in.
Press the button to save the settings
and exit this menu. By pressing
reconnect buttons to verify server
availability. If the server is still not
available, check the network
connection and hardware settings.
Enter pin code.
1
2
3
4
7
REF
5x
Other SAFECONTROL Monitor manuals
