Ruijie RGOS 11.X User manual
Ruijie RGOS 11.X High-end Data Center
Switches
(N18000-X) Installation
Contents
■Hardware Installation
Hardware Installation
Preparations Installing the Chassis
to a Specified
Position Grounding Installing Power
Modules or Cards Checking
Tip: Read the Hardware Installation Manual if you install the switch for the first time.
Safety Notes
Do not install the switch in a wet place and keep it away from liquid.
Do not wear loose clothes during installation to avoid hooking components and causing damage.
Therefore, fasten clothes ribbons, scarves, and sleeves.
Place tools and components away from passageways to prevent collision.
Check for potential risks in the working area, for example, ungrounded power supplies, unreliable
grounding of power supplies, or wet floor.
Ambient Requirements
Temperature: 0C to 45C
Relative humidity: 10% to 90%
Cleanness: ≤ 1.4×105(particle diameter ≥ 5 μm)
Ventilation: at least 20 cm clearance around the chassis for efficient heat dissipation
Anti-interference: far away from high-power (radar or radio transmitting station), high-frequency, or
large-current devices
Hardware Installation
Preparations Installing the Chassis
to a Specified
Position Grounding Installing Power
Modules or Cards Checking
Confirming the Cabinet Specifications
The cabinet depth (distance between the front
and rear doors) must be large than 1200 mm.
There must be a distance of more than 180 mm
between the front mounting rails and front door of
the cabinet, and the thickness of the front door
must be smaller than 25 mm, so that more than
155 mm space is available. See Figure 1.
The load capacity of the cabinet must be large
than 400 kg.
If the N18000-X switch uses RG-PA2700I power
modules, check whether the cabinet is an IEC
cabinet, in which the PDU provides power outlets
as shown in Figure 2. In this case, use C19-C20
power cables as shown in Figure 3.
Figure 2 Figure 3
Figure 1
Hardware Installation
Preparations Installing the Chassis
to a Specified
Position Grounding Installing Power
Modules or Cards Checking
Unpacking:
An N18000-X series switch
is packed in carton, so it
can be unpacked more
quickly than an N18000
series switch.
You will find a wrench and a
screwdriver in the carton.
Use them to remove the four
L-shaped plates that fix the
chassis on the pallet. Remove
screws used to
fix the chassis
Hardware Installation
Preparations Installing the Chassis
to a Specified
Position Grounding Installing Power
Modules or Cards Checking
Moving the Chassis: Operation by Four
Persons Recommended
Precautions:
1. Do not hold the panels, power module
handles, or chassis handles when moving
the chassis. These parts are not
designed to bear the weight of the whole
chassis. Holding them to move the
chassis may cause damage to the parts
or even personal injury.
2. Before moving the chassis, remove the
Supervisor Engine modules, line cards,
and power modules to reduce weight of
the chassis.
Do not hold
fan handles
when moving
the chassis
Hardware Installation
Preparations Installing the
Chassis to a
Specified Position Grounding Installing Power
Modules or Cards Checking
Installing Shelf Brackets
An N18000-X chassis is delivered with a
pair of expandable shelf brackets.
Reserve 2 U height above the cabinet
bottom for shelf bracket installation. The
two shelf brackets are marked RIGHT
and LEFT to identify their installation
positions.
See the figure on the right for installation
positions of the shelf brackets.
Hardware Installation
Preparations Installing the
Chassis to a
Specified Position Grounding Installing Power
Modules or Cards Checking
There Is a Ground Bar in the Installation Environment
(Recommended)
①Remove the ground screw from the rear panel of the
chassis.
②Put the OT terminal of the ground cable delivered
with the switch on the ground screw of the chassis.
③Install the ground screw with the OT terminal to the
ground hole, fasten it with a screwdriver, and connect
the other end of the ground cable to the ground bar
of the equipment room. (Adjust the length of the
ground cable based on the distance with the ground
bar.)
There Is No Ground Bar in the Installation Environment
If the switch adoptsAC power supply, the PE cable of the
AC power supply needs to be grounded. Check whether
the PE cable of theAC power supply is properly grounded
in the power distribution room or on theAC transformer
side.
Hardware Installation
Preparations Installing the
Chassis to a
Specified Position Grounding Installing Power
Modules or Cards Checking
Installing Power Modules
All the chassis models have power module
slots at two sides of the chassis.
Precautions:
1. Ensure that there are no objects, such
as a PDU, near the rear mounting rails
within depth of the chassis in the cabinet
to hinder installation or removal of power
modules.
2. Each power module has a locking latch.
After connecting a power cable to a
power module, close the locking latch
to secure the power cable.
Two columns of
power modules
Hardware Installation
Preparations Installing the
Chassis to a
Specified Position Grounding Installing Power
Modules or Cards Checking
Installing Line Cards
Caution: N18000-X line cards do not use self-locking ejector levers.
This manual suits for next models
1
Table of contents
Other Ruijie Switch manuals
Ruijie
Ruijie RG-EG210G-P User manual
Ruijie
Ruijie RG-S6150-X Series How to use
Ruijie
Ruijie RG-S6910-3C Series Installation and operating manual
Ruijie
Ruijie RG-S6250-48XS8CQ Series Manual
Ruijie
Ruijie RG-NBS3200 Series Installation and operating manual
Ruijie
Ruijie Reyee RG-NIS Series User manual
Ruijie
Ruijie RG-S6220-H Series User manual
Ruijie
Ruijie RG-SF2920 Series Installation and operating manual
Ruijie
Ruijie RG-S6100 Series How to use
Ruijie
Ruijie RG-S2900G-E Series User manual
Ruijie
Ruijie RG-S6580-48CQ8QC Installation and operating manual
Ruijie
Ruijie RG-NBS3100 Series Installation and operating manual
Ruijie
Ruijie RG-S7808C Series Installation and operating manual
Ruijie
Ruijie RG-S7800C Series Installation and operating manual
Ruijie
Ruijie XS-S1920 Series Installation and operating manual
Ruijie
Ruijie RG-S6510-32CQ Installation and operating manual
Ruijie
Ruijie RG-ES1 Series Installation and operating manual
Ruijie
Ruijie Reyee RG-NBS5200-24GT4XS-P Installation and operating manual
Ruijie
Ruijie Reyee RG-ES126S-P V2 User manual
Ruijie
Ruijie RG-S6930-2C Installation and operating manual
