RuggON MT7000 User manual
Front View
PACKAGE LIST
PRODUCT INTRODUCTION
Before you begin the installaon or conguraon process, make sure all the components and
accessories are intact. Contact your representave if any is missing or damaged. Please verify the
delivery of the contents upon receipt.
■MT7000 in-vehicle terminal
■Quick Start Guide
■Circular power connector to Fork Terminals (Length: 300mm)
■2-feet DB15 male connector cable with mulple end
■2-feet DB15 male connector cable (no terminaon)
NOTE: The packaging material provides opmal protecn to your device. Aer unpacking, DO store the
original packaging material in the event that you need to return for shipment.
PRODUCT INTRODUCTION
MT7000
Ambient light sensor
Display turn on/o
Volume
Power & Communicaon
LED indicators
Funcon buons Speaker
Speaker
The LEDs on MT7000 are status indicators that show the operang status of your system.
LED Status Description
Power Blink Yellow Load boot loader
Power Solid Green System ready to use
Power Blink Red Vehicle baery abnormal
Communicaon Solid Green WWAN enabled
The power management,
DashON.
The MT7000 supports a standard VESA version
MIS-D, 75, C (75mm distance quadrate order, M5
thread, deepness 6mm) with four mounng holes
on the back side of the device.
Rear View
Bo�om View
DC- in
GNSS(SMA Jack)
Oponal WWAN Antenna
Connector (SMA Jack)
Oponal Wi-Fi/BT Antenna
Connector (SMA Jack)
RS-232(COM1) with 5/12V power output
USB, RS -
232/422/485 (COM2)
LAN
DIO/ CAN bus
Side View
SIM Card Slot
Micro SD Card Slot
Headset jack
Reset buon
USB Type A
LED Status Description
Power Blink Green Power up
MT7000
Mobile Data Terminal
Quick Start Guide
P/N: 25U100014-001
Wire Color Description
RED V+
BLACK V-
GREEN PE (Safety Ground)
WHITE ACC/ Ignion
POWERING ON THE SYSTEM CONNECTOR PIN ASSIGNMENTS
MT7000 allows a wide range of DC power input from 9~36V via a 3-pin circular power cord.
There are two opons to start up the MT7000, either via car power cable or external power
adapter.
Fuse Requirements
Fuses* are required in connecng the
power cable and bery in series and add
3A fuse in ACC/ignion line to avoid the
risks of wire damage and vehicle burning.
For detailed power wiring diagram, please
refer to the Powering the System secon
of Chapter 4 in MT7000’s user manual.
Make sure that all power supplies are
disconnected when you plug the
power cord into the power connector.
1. The bare wire lead cable lets you directly wire to 12V or 24V car power supply.
2. Please refer to the wire denion below for connecng your power source.
Power on through external power adapter
Please connect red (V+) wire to white (ACC/ Ignion) wire to power on MT7000 through an
external power adapter. ACC/Ignion mode is not supported in such condion.
Notes:
* 5A for 24VDC power input
* 10A for 12VDC power input
MT7000 P/N: 25U100014-001
Power Connector
Pin Description
1 DC+
2 GND
3 ACC/ Ignon
USB and RS-232/422/485 Port (COM2)
Pin Description Pin Description
1 RS-422 TX+ 9 USB 5V
2 RS-422 RX+ 10 RS-232 RX
3 RS-485 TX+ 11 GND
4 RS-232 TX 12 USB DP
5 GND 13 USB DM
6 RS-422 TX- 14 USB 5V
7 RS-422 RX- 15 NC
8 RS-485 TX-
DIO and CAN bus Port
Pin Description Pin Description
1 CAN_H 9 CARD POWER
2 N/A 10 GND
3 N/A 11 SOS
4 N/A 12 DIO_OUT1 (5V 10mA)
5 N/A 13 DIO_IN1 (5V 100mA)
6 CAN_L 14 DIO_IN2 (5V 100mA)
7 N/A 15 DIO_OUT2 (5V 10mA)
8 N/A
Red
Green
Black
White
Lines to
Safety
Ground
5A/10A
FUSE 3A
FUSE
1
5
15 11
1
5
15 11
2
13
Other manuals for MT7000
1
Other RuggON Touch Terminal manuals
