Rosslare SA-26 User manual

SA-26/27/28

1/2/4-Button Remote

Control Transmitter

Q: What is a Transmitter ?

A: A transmitter is an electronic device that uses RF

energy and coded digital messages to control and

communicate commands to other electronic

products.

Q: What is SA-26/27/28 WIRELESS REMOTE and how

can it benefit me ?

A: SA-26/27/28 allows the user ARM and DISARM a

Security Panel Access Control Reader, PANIC or

even turn on and off the lights and appliances using

a Universal Receiver by the use of RF signal.

Q: What is SUPERVISOR or SUPERVISED sensor ?

A: A Supervised sensor continuously reports to the

receiver or security panel to confirm status of the

sensor and its presence. If the receiver fails to hear

from a sensor within a pre-programmed time, it

will presume a sensor is missing or malfunctioning

and notify the user. This provides added security.

INTRODUCTION (FAQ's) - continued;

OPERATION - GENERAL NOTES

Use only the specified AAA-sized 1.5 Volt Alkaline

Battery.

1) Push down the Battery Compartment Latch and lift to

remove (FIG 1).

2) For a new unit, simply remove the plastic strip

contact breaker. For replacement, remove the battery

by using a small screwdriver (FIG 2).

CAUTION: Notice the polarity of the battery (+) and (-)

must coincide with the markings (+) and (-) on the

plastic. Check that the battery is held securely.

3) Dispose of the old battery properly.

Do not incinerate, heat, disassemble, recharge.

4) To test, press the buttons on the remote control and

see if there is a transmission. The LED will light to

indicate an RF transmission (FIG 3).

5) Close the front cover, by engaging the ridges of the

top case and bottom case near the keychain eye

hole, align and gently press together both covers and

replace the locking screw.

FIG 1: Back of the SA-26/27/28

Housing

The SA-26/27/28 is a miniature radio transmitter,

designed to send coded RF transmissions to wireless

receivers and control panels. The transmissions are

activated by depressing one of the pushbuttons (1, 2 or

4 - depending on model) on the unit.

After Removing the

battery compartment

cover, remove the

old batteries and

install the batteries in

the correct alignment

shown.

FIG 2: Replacing the 2 AAA-sized Batteries

After activating or replacing the battery in the SA-26/27/

28, test the transmitter by pressing each one of the three

buttons to see if there is a transmission.

When pushing one of the transmit buttons, the LED will

flash to indicate a transmission.

FIG 3: Testing the Buttons

Fig 4: Back of the SA-26/27/28 Cover

Step 3: RECEIVER COMPATIBILITY

The installation procedure for using the SA-26/27/28

remote control varies from product to product.

Full instructions are printed within the installation

manual each of the receiver panels or controls.

For this instruction manual, the instructions cover only

the SP-06 V Wireless Security Control Panel in 433.92 or

868.35 MHz;

The following pages show the simplified enrollment

procedures for enrolling SA-26/27/28 transmitters to

Rosslare’s SP-06 V panel. For full details about the

Wireless Control Panel, please refer to the SP-06 V

Installation and Programming Manual.

AND IMPORTANT INFORMATION

INSTALLATION INSTRUCTIONS

P/N: 0706-0960079+01

GENERAL DESCRIPTION

INTRODUCTION (FAQ's)

Q: What is LOW BATTERY detection ?

A: For all supervised sensors, LOW BATTERY

detection is when a sensor continuously measures

its battery state and transmits a low battery signal

to the security panel when the battery's voltage

drops below a certain level. This alerts the user in

advance to replace a weak battery.

Q: What is a CASE TAMPER detector?

A: A Case Tamper detector monitors any unauthorized

opening of the unit housing. A signal will be

transmitted to the security panel to notify the user

of such tampering.

Q: What is a BACK TAMPER detector ?

A: Once the sensor is mounted and activated, the Back

Tamper detector ensures that the sensor is not

removed or vandalized by detecting any removal of

the unit from a wall or corner. The Back tamper

detector will alert the security panel in such cases.

The SA-26/27/28 remote control is activated by pressing

the buttons on the unit and transmits this information to

the receiver panel.

Since the SA-26/27/28 is a portable wireless device and

system reception is dependent upon the conditions of

use as follows:

STEP-1 BATTERY INSTALLATION (Fig1,2)

STEP-2 TESTING THE TRANSMISSION

The SA-26/27/28 in 433,92 or 868.35 MHz frequency is

compatible with a variety of Rosslare's security panels,

universal receiver controls, and system components.

SP-06 V Wireless Security Control Panel,

SA-22 Dual Channel Receiver,

SA-38 Channel Receiver,

AY-L23 Wireless Receiving Wiegand 26, Reader

SA-29 Wireless Repeater with UPS - System Level

and others...

For an updated list please contact your distributor,

dealer or agent.

12 3

45 6

78 9

10 11 12

SA-26/27/28 Instruction Manual - Version 1.0 (Page 1/2)

- AVOID: Placing the SA-26/27/28 near strong

magnetic or electrical fields other than the magnet with

which it is intended to be used. Otherwise,

performance could be affected and false alarms could

occur.

- AVOID: Using near or behind large metal surfaces and

multiple concrete/steel walls. This may interfere or

block the wireless signals. Make sure to test the range

from the desired location by using the RF Test

Procedure to ensure reception.

- IMPORTANT NOTE: When the battery power has been

depleted, as indicated by a very dim LED, replace the

battery immediately.

The SA-26/27/28 can control up to 4 functions when

used with Rosslare’s Wireless Security Control Panels

or Universal RF Receivers. The SA-26/27/28 is a battery

operated wireless device using a standard 12 Volt

Alkaline battery. An LED (Light Emitting Diode) lights

during the transmission of the RF signal. Which lights

when the battery voltage exceeds 8 VDC. If the LED

does not light during the transmission, the battery

must be replaced immediately.

SA-26/27/28 is a high quality wireless sensor packed

with intelligent wireless and system features such as

compatibility with RF Repeaters. Inside the SA-26/27/28

is a state of the art microprocessor, with ASK RF

transmitter technology, and is encoded with 16 million

factory programmed non-recurring ID codes ensuring

that multiple units can be used on a single system.

Turn the unit over and

pull the battery

compartment cover

latch down, and lift, to

open.

LED Function:

LED will flash when

the SA-26/27/28 is

transmitting

Function:

ARM Button for

the Security

Panels or

Single Channel

Transmitter

Function:

Disarm Button

for the Security

Panels or Single

Channel

Transmitter

Function:

Emergency Panic

Button for the

Security Panels or

Single Channel

Transmitter

Place the battery

compartment cover

back into the latch,

swing shut, until the

top latch clicks shut.

The SA-26/27/28 in 433.92 or 868.35 MHz, is compatible

with receivers from Rosslare, including the SP-06 V

wireless security control panel. This is a short enrolling

tutorial for the SP-06 V Panel.

The SA-26/27/28 can be installed by enrollment to ZONE

8 of the SP-06V Panel. Zone 8 can accommodate up to 8

(eight) handheld Remote controls or RF keyboard

transmitters.

SA-26/27/28 Remote Control enrolls to any one of the

eight addresses in Zone 8 of the SP-06V Wireless

Security control panel.

When installed onto the SP-06 V panel, the SA-26/27/28

will have one ARM/ PARTIAL ARM, one DISARM and one

PANIC button, active for 24 hours from any mode of the

SP-06V.

Enrolling the SA-26/27/28 to Zone 8 of SP-06 V:

1) Using the installer pass code (8888) by pressing the

MENU button and entering the code on the keyboard,

enter the Installer Menu.

You will then enter the installer programming menu

for the SP-06 V control panel

SILENT

PANIC

Zone

Num b er

Remote ControlType Displa

PANIC = Audiable Pani

SILENT = Silent Duress Alarm

Zone Box Status Displa

ZONE

= Zone is armed

ZONE

(flashing)= Zone was triggered

LCD Example of ZONE BOX Display

432

5 6 7 8

OFFMENU

ESC

SET

INSTALL CODE

MASTER CODE

ZONE

PANIC

ESC

ENTER

SUPERVISION

MASTER CO DE

USER CODE

SET OUTPUT

SIREN TIME

EXIT DELAY

CLOCK

SYSTEM

TEST

PARTIAL

OFF

MODE

SET SIREN

SILENT PANIC

CTIVATE

CHIME

CODE

ENTRY DEL AY

CLEAR R/F

ADD R/F

SET ZONE

TELEPHONE

ZONE

ESC

NUMBER

ENTRY DELAY

CLEAR R/F

ADD R/F

SET ZONE

ZONE

ESC

ENTER

ADD R/F

SET ZONE

ZONE

PANIC

ZONE

CLEAR R/F

Battery: Two 1.5-Volt AAA Alkaline Battery

Use only the specified 1.5-Volt Alkaline Battery

Operating Temp: -10

oC to +50oC

[14oF to + 122oF]

Operating

Humidity: Up to 95% Non-Condensing (max.)

Alarm Transmit: 500 ms (milliseconds)

RF Frequency: Available in 433.92 or 868.35 MHz

Usage: Carried in pocket or worn on a belt; for indoor (dry) use only.

Tamper: The SA-26/27/28 has no tamper transmission.

Supervisor: The SA-26/27/28 is not a supervised transmitter.

Current: Standby - 0 A

Transmit - 16 mA

Size: 104mm (h) x 40mm (w) x 15mm (d)

(4.09 " x 1.57" x 0.59")

Weight: 28 grams including battery.

Color: Brown

The Manufacturer does not represent that its Product may not be compromised and/or

circumvented, or that the Product will prevent any death, personal and/or bodily injury and/or

damage to property resulting from burglary, robbery, fire or otherwise, or that the Product will

in all case provide adequate warning or protection. User understands that a properly

installed and maintained alarm may only reduce the risks of events such as burglary, robbery

and fire without warning, but is no assurance or a guarantee that such will not occur or that

there will be no death, personal damage and/or damage to property as a result.

The Manufacturer shall have no liability for any death, personal and/or bodily injury

and/or damage to property or other loss whether direct, indirect, incidental,

consequential or otherwise, based on a claim that the Product failed to function.

However, if the Manufacturer is held liable, weather directly or indirectly, for any loss of

damage arising under this limited warranty or otherwise, the Manufacturer’s maximum

liability shall not in any case exceed the purchase price of the Product, which shall be fixed

as liquidated damages and not as a penalty, and shall be the complete and exclusive remedy

against the Manufacturer.

Warning: The user should follow the installation and operation instructions and among other

things test the Product and the whole system at least once a week. For various reasons,

including, but not limited to, changes in environmental conditions, electric or electronic

disruptions and tampering, the Product may not perform as expected. The user is advised to

take all necessary precautions for his/her safety and the protection of his/her property.

MENUMENU

2) In the INSTALLER MENU, press the down arrow to

select the ZONE menu and press Enter

3) In the ZONE menu, when prompted for the zone

number, press the number 8 to select Zone 8.

88 88 88

4) To program operation of the Panic Button Use the

down arrow to select SET ZONE option and Press

Enter.

5) Press the SET key until the zone type shows “PANIC”,

for an audible emergency alarm, to enable the SA-26/

27/28 to perform a non audible alarm, scroll to

“SILENT PANIC”. Press ENTER to enable your

selection of either PANIC to sound or not to sound an

ALARM at the panel, if the alarm is transmitted from

the SA-26/27/28 Remote Control.

6) Within the zone 8 menu, use the arrow key to select

ADD RF and press enter, use the arrow key to select

the desired available slots from 8.1 to 8.8, and

press ENTER.

7) When Prompted for RADIO, press any pushbuttons

on the SA-26/27/28 to transmit,

ESC

ENTER

ADD R/F

SET ZONE

ZONE

PANIC

ZONE

CLEAR R/F

ENTERENTER

SETSET

ENTERENTER

ESC

ENTER

SET

ADD R/F

ZONE

ONZE

PANIC

ENTERENTER

8) When the control panel receives the coded signal

from the SP-03 V there will be a been and an

indication to press enter on the LCD. Press the

ENTER button on the panel’s keyboard.

9) Once the SA-26/27/28 is enrolled onto the SP-06 V

control panel, the remote control may be used to

perform 4 Functions, such as ARMING (Full Away

Arming all Zones), PARTIAL ARMING (Part Zones

Arming for Stay), DISARMING, and EMERGENCY

PANIC.

ENTERENTER

! Warning !

Changes or modifications to this equipment not

expressly approved by the party responsible for

compliance (Rosslare Enterprises Ltd.) could void

the user's authority to operate the equipment.

Our wireless systems are very reliable and are tested to

high standards. However, due to their low transmitting

power (required by international standards imitations)

there may be some limitations to be considered:

A. Receivers may be blocked by radio signals occurring

on or near their operating frequencies, regardless of

the ID.

B. A receiver can respond to one transmitted signal at a

time

C. Wireless equipment should be tested regularly (At

least once a week) to determine if there are sources

of interference and protect against faults.

MISCELLANEOUS COMMENTS SA-26/27/28 SPECIFICATIONS

Rosslare Enterprises Ltd. And/or its subsidiaries and its affiliates (“the Manufacturer”)

warrants it’s products hereinafter referred to “the Product” or “Products” to be in conformance

with it’s own plans and specifications and to be free of defects in materials and workmanship

under the normal use and service for a period of twelve months from the date of shipment by

the Manufacturer. The Manufacturer’s obligations shall be limited within the warrantee

period at its option to repair or replace the product or any part thereof. The manufacturer

shall not be responsible for dismantling and/or reinstallation charges. To exercise the

warranty the product must be returned to the Manufacturer freight prepaid and insured.

This Warranty does not apply in the following cases: improper installation, misuse,

failure to follow installation and operating instructions, alteration, abuse, accident or

tampering, and repair done by anyone other than the Manufacturer.

This warranty is exclusive and expressly in lieu of al other warranties, obligations or liabilities,

weather written, oral, express or implied, including warranty of merchantability or fitness for a

particular purpose, or otherwise. In no case shall the Manufacturer be liable for any

consequential damages for breach of this warranty or any other warranties whatsoever, as

aforesaid.

This warranty shall not be modified, varied or extended, and the Manufacturer does not

authorize any person to act on it’s behalf in the modification, variation or extension of this

warranty. This warranty shall apply to the Product only. All products, accessories or

attachments of others used in compilation with this product, including batteries, shall be

covered solely by their own warranty, if any. The manufacturer shall not be liable for any

damage or loss whatsoever, weather directly, indirectly, incidentally, consequentially or

otherwise, caused by malfunction of the Product due to products, accessories, or

attachments of others, including batteries, used in conjunction with the Products.

STANDARDS COMPLIANCE

European Standards Compliance:

Meets the requirements of the Harmonized

European Standards for CE Mark.

ETS 301 459

ETS 300 220

Step 4: INSTALLING TO THE SP-06 V

WIRELESS SECURITY CONTROL PANEL

12 14 15

16 17 18

19 20 21

WARRANTY

22 23 24

SA-26/27/28 Instruction Manual - Version 1.0 (Page 2/2)

TECHNICAL SUPPORT

Asia Pacific, Rosslare Security Products Headquarters

Middle East 905-912 Wing Fat Industrial Bldg,

and Africa 12 Wang Tai Road, Kowloon Bay Hong Kong

Tel: +852 2795-5630

Fax: +852 2795-1508

E-mail: support.apac@rosslaresecurity.com

United States 1600 Hart Court, Suite 103 Southlake, TX, USA 76092

and Canada Toll Free: +1-866-632-1101

Local: +1-817-305-0006

Fax: +1-817-305-0069

E-mail: support.na@rosslaresecurity.com

Europe Global Technical Support & Training Center

HaMelecha 22, Rosh HaAyin, Israel 48091

Tel: +972 3 938-6838

Fax: +972 3 938-6830

E-mail: support.eu@rosslaresecurity.com

South America Pringles 868, 1640 Martinez, Buenos Aires, Argentina

Tel: +54 11 4798-0095

Fax: +54 11 4798-2228

E-mail: support.la@rosslaresecurity.com

Web Site: www.rosslaresecurity.com

Press:

any other button to

generate an RF

transmission to

enroll the SA-26/

27/28 to the

Control Panel.

Function:

DISARM (Short Press)

Function:

ARM (Short Press)

PARTIAL ARM (Long

Press)

LED Function:

LED will flash when the

SA-26/27/28 is

transmitting

Function:

PANIC (2 second Press)

This manual suits for next models

Other Rosslare Transmitter manuals

Rosslare

Rosslare SAK-25 User manual

Popular Transmitter manuals by other brands

NIVELCO

NIVELCO EasyTREK SCA-300 Series Programming manual

Honeywell

Honeywell 5816WMBR installation instructions

Kamstrup

Kamstrup READy MTU Installation and operation guide

Omega

Omega ZW Series user guide

ABB

ABB Field 264H Instructions for installation

Alinco

Alinco DJ-V17T Service manual

Dejero

Dejero EnGo 3x manual

Rosemount

Rosemount 4600 Reference manual

Speaka Professional

Speaka Professional 2342740 operating instructions

trubomat

trubomat GAB 1000 instruction manual

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 instructions

Rondish

Rondish UT-11 quick start guide

MG 10JRE instruction manual

Burkert

Burkert 8177 operating instructions

Firetide

Firetide HotPort 3203 Hardware installation guide

Tele Radio

Tele Radio T9-02 User instructions

Rotronic

Rotronic HygroFlex HF3 Series user guide

Jamara

Jamara FCX6 Pro Tel Instruction