Rosslare AY-HRMR12B User manual

AY-HR/JR/KR/LR/MR12B

Proximity Readers

Installation Manual

1. Introduction

The AY-xR12B Series Proximity Readers (models AY-

HR12B/JR12B/KR12B/LR12B/MR12B) are RFID proximity card readers to

be installed for use with access control systems.

Figure 1: AY-xR12B Series

H J K L M

2. Technical Specifications

2.1 Electrical Characteristics

Power Supply Type Linear type (recommended)

Operating Voltage Range 5 to 16 VDC

Maximum Input Current AY-KR12B

AY-JR12B

Standby: 35 mA

Read: 50 mA

AY-HR12B

AY-LR12B

AY-MR12B

Standby: 35 mA

Read: 100 mA

Tamper Output Open collector, active low, max sink current

16 mA

Max Cable Distance to

Controller

150 meters (500 ft.)

RF Modulation ASK

Output Format Wiegand 26-Bit

Read Range (Max)* AY-HR/LR12B 12 cm (4.7 in.)

AY-JR/MR12B 10 cm (3.9 in.)

AY-KR12B 8 cm (3.2 in.)

* Measured using a Rosslare proximity card or equivalent. Range also

depends on electrical environment and proximity to metal.

2.2 Environmental Characteristics

Operating Environment Suitable for outdoor use (IP68)

Operating Temp. Range -31°C to 63°C (-25°F to 145°F)

Operating Humidity Range 0 to 95% (non-condensing)

Regulatory Approvals USA: UL 294 and FCC Part 15B

Europe: CE Listed

2.3 Physical Characteristics

Model Dimensions

(H x W x D)

Weight

AY-HR12B 109.91 x 74.91 x 15 mm (4.3 x 3.0 x 0.6 in.) 100 g (3.5 oz)

AY-JR12B 119.95 x 41.95 x 14 mm (4.7 x 1.7 x 0.6 in.) 88.5 g (3.1 oz)

AY-KR12B 79.91 x 39.91 x 12.8 mm (3.2 x 1.6 x 0.5 in.) 70.5 g (2.5 oz)

AY-LR12B 144.91 x 42.91 x 20 mm (5.7 x 1.7 x 0.8 in.) 116 g (4.1 oz)

AY-MR12B

88.91 x 88.91 x 15 mm (3.5 x 3.5 x 0.6 in.) 109 g (3.9 oz)

3. Mounting Instructions

Mount the reader with the appropriate screws (not supplied) as

indicated on the template.

To mount the reader:

1. Remove the snap-off cover to access the screw holes.

2. Determine an appropriate mounting position for the reader.

3. Peel off the back of the self-stick mounting label template included

with the unit and place at the desired mounting position.

4. Using the template as a guide, drill two holes for mounting the

reader to the surface. The hole size is indicated on the mounting

template (Figure 2).

5. Drill a 10-mm (7/16") hole for the cable. If mounting on metal,

place a grommet or electrical tape around the edge of the hole.

6. Route the interface cable from the reader to the controller. A

linear type power supply is recommended.

The proximity reader can also be mounted using strong epoxy

glue. After application, the reader should be firmly held in

place until the glue dries.

Card readers are to be used with a listed access control unit whose power

supply is UL Listed Class 2 or equivalent.

Figure 2: Mounting Templates

H J K L M

4. Wiring Instructions

The proximity reader is supplied with a 45-cm (18”) pigtail, having a 6-

conductor cable.

To connect the reader to the controller:

1. Prepare the reader cable by cutting the cable jacket back 3.4 cm

(1¼”) and strip the wires 1.3 cm (½”).

2. Prepare the controller cable by cutting the cable jacket back 3.4

cm (1¼”) and strip the wires 1.3 cm (½”).

3. Splice the reader pigtail wires to the corresponding controller wires

and cover each connection (Table 1).

Table 1: Wiring

Color

Wiegand Output

Red DC + Input

Black Ground

Green Data 0

White Data 1

Brown LED Control

Purple Tamper

4. If the tamper output is being utilized, connect the purple wire to

the correct input on the controller.

5. Trim and cover all conductors that are not used.

•The individual wires coming out of the reader are color coded

according to the recommended Wiegand standard.

•When using a separate power supply for the reader, this supply

and the controller's power supply must have a common ground.

•The cable shield wire on the reader should be attached to an earth

ground (best) or signal ground connection at the panel or power

supply end of the cable. This configuration is best for shielding the

reader cable from external interference.

5. Testing

The reader should be tested after wiring it to a power supply and the

controller.

To test the reader:

1. Power up the reader.

The LED and beeper activate three times. This indicates that the

reader is working properly.

2. Present the appropriate type of proximity card to the reader.

The LED momentarily flashes green and a short beep is emitted.

This indicates that the card was read properly by the proximity

reader.

After the card data is processed by the controller, the controller can

then turn the LED green.

Refer to the controller description of the LED operation if the reader

LED is controlled by the controller.

Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including

interference that may cause undesired operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to

operate the equipment.

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Limited Warranty

The full ROSSLARE Limited Warranty Statement is available in the Quick

Links section on the ROSSLARE website at www.rosslaresecurity.com.

Rosslare considers any use of this product as agreement to the

Warranty Terms even if you do not review them.

Contact Information

United States and Canada

Rosslare Security Products, Inc.

Southlake, TX, USA

Toll Free: +1-866-632-1101

Local: +1-817-305-0006

Fax: +1-817-305-0069

support.na@rosslaresecurity.com

Europe

Rosslare Israel Ltd.

Rosh HaAyin, Israel

Tel: +972-3-938-6838

Fax: +972-3-938-6830

support.eu@rosslaresecurity.com

Latin America

Rosslare Latin America

Buenos Aires, Argentina

Tel: +54-11-4001-3104

support.la@rosslaresecurity.com

China

Rosslare Electronics (Shenzhen) Ltd.

Shenzhen, China

Tel: +86-755-8610-6842

Fax: +86-755-8610-6101

support.cn@rosslaresecurity.com

Asia Pacific, Middle East, Africa

Rosslare Enterprises Ltd.

Kowloon Bay, Hong Kong

Tel: +852-2795-5630

Fax: +852-2795-1508

support.apac@rosslaresecurity.com

India

Rosslare Electronics India Pvt Ltd.

Tel/Fax: +91-20-40147830

Mobile: +91-9975768824

sales.in@rosslaresecurity.com

www.rosslaresecurity.com

0706-0960166+01

This manual suits for next models

Other Rosslare Other manuals

Rosslare

Rosslare MD-CC101 User manual

Popular Other manuals by other brands

GO Industries

GO Industries 38017 installation instructions

Cissell

Cissell 30LBCMAN2 manual

RIDGID

RIDGID K-60SP manual

Gage Bilt

Gage Bilt GB751SH-5 Original instructions

OVE

OVE SIERRA 60 installation manual

ReelCraft

ReelCraft 7800 OLB21 operating instructions

Body Armor 4x4

Body Armor 4x4 ECO-SERIES user manual

ROBLIN

ROBLIN DROP Dimensions

EMG

EMG EMG-ACB BARREL Installation information

MiniSolar

MiniSolar MT-150 Assembling Guide

Parkside

Parkside PSZ 250 B2 Operation and safety notes

ABB

ABB REM 610 Technical reference manual

Parkside

Parkside 55992 translation of original operation manual

Skyjacker

Skyjacker F250 installation instructions

IBM

IBM IBM SYSTEM Z overview

Grech Motors

Grech Motors G28 owner's manual

NOVAK

NOVAK BATTERY CARE SHEET Using

Telemotive

Telemotive blue PiraT Mini Startup guide