Rosslare AY-Z12 User manual

Long range Multi Reader

AY-Z12

Installation Guide

May 2009

Table of Contents

AY-Z12 Installation Manual Page ii

Table of Contents

1. Introduction......................................................................3

2. Technical Specifications ..................................................5

3. Installation........................................................................6

3.1 The Installation Kit...................................................6

3.2 Installing the AY-Z12 Long Range Reader:.............6

4. Wiring Instructions..........................................................9

5. Operation Instructions ..................................................10

Appendix A: Limited Warranty...................................11

Appendix B: Technical Support...................................13

Introduction

1. Introduction

The AY-Z12 Long-range Reader is an RFID proximity card reader,

utilized with access control systems.

Figure 1 The AY-Z12 Long-Range Reader

This Manual contains the following information:

•Installation

•Wiring Instructions

•Operation Instructions

Page 3 AY-Z12 Installation Manual

Introduction

AY-Z12 Installation Manual Page 4

The AY-Z12, while easy to install and set up, must be installed

professionally.

This product has only one available channel.

Pursuant to FCC §15.21 [ 54 FR 17714 , Apr. 25, 1989, as amended

at 68 FR 68545 , Dec. 9, 2003], changes or modifications made to

equipment, which are not expressly approved by Rosslare

Enterprises, Ltd., may void the user's authority to operate the

equipment.

Technical Specifications

AY-Z12 Installation Manual

Page 5

2. Technical Specifications

Electrical Characteristics

Power Supply Type Linear type - recommended

Operating Voltage Range

10 - 16VDC

Absolute Maximum

(non-operating) 18VDC

Input Current Standby: 280mA

Read: 330mA

Tamper Output Open collector, active low, max.

sink current 30mA

Maximum Cable Distance

to Controller 500 ft (150 meters)

Card Read Distance Weigand 26 output format with a

23.6" (60 cm) maximum read

range*

Environmental Characteristics

Operating Temp. Range -22°F to 145° F (-30°C to 63°C)

Operating Humidity 0 – 95% (non-condensing)

Suitable for outdoor use (IP54)

Dimensions

Height x Width x Depth 11.81" x 11.81" x 1.0"

300mm x 300mm x 25.4 mm

Weight 2.35 Lbs. (1066g)

* Measured using Rosslare Proximity Card AT-R14 or equivalent. Range also

depends on electrical environment and proximity to metal.

Installation

3. Installation

3.1 The Installation Kit

The Installation kit comprises of the following items that are to be

used during the installation procedure:

•One Installation Template

•Four pan head screws & wall plugs

•One L shaped security screw tool

•Three Security screws

3.2 Installing the AY-Z12 Long Range Reader:

AY-Z12 Installation Manual Page 6

Installation

Figure 2: Removing the Top Cover

Figure 2shows the front view of the AY-Z12 Long-Range Reader.

When installing the reader, you must remove the snap-off cover to

access the screw holes.

The Reader must be mounted with the appropriate screws (not

supplied), as described in the template provided.

Installing the unit on metal surfaces will reduce the read range

considerably, to decrease the affect of the metal surface use

Rosslare’s MP-Z02 Spacer (sold separately) as described in the

image below for a max range of 43cm (17 inch).

Figure 3: Installing the unit with the MP-Z02 spacer

Page 7 AY-Z12 Installation Manual

Installation

AY-Z12 Installation Manual Page 8

To Install the Reader:

1. Determine an approximate location for the installation of the

Reader.

2. Peel off the back of the self-adhesive installation label

template and locate it at the required location.

3. Using the template as a guide, drill the holes (the size of

which are indicated in the template) to install the Reader or

spacer onto the surface.

4. Drill a 7/16” (10mm) hole for the cable. In the event that you

are installing the reader on metal, place a grommet or

electrical tape around the edge of the hole and use the MP-

Z02 spacer.

5. Route the interface cable from the Reader to the Controller.

A linear type power supply is recommended.

Wiring Instructions

4. Wiring Instructions

The AY-Z12 Reader is supplied with an 18” pigtail, comprising a 6-

conductor cable.

To connect the Reader to the Controller:

1. Prepare the Reader cable by cutting its jacket back 1¼” and

strip the insulation from the wires, ½”.

2. Prepare the Controller cable by cutting its jacket back 1¼”

and strip the insulation from the wires, ½”.

3. Splice the Reader’s pigtail wires to the corresponding

Controller wires and cover each joint with insulating tape.

If the tamper output is being utilized, connect the purple wire

to the correct input on the Controller.

Reader Color Weigand Output

10~16 VDC Red DC+Input

Shield / Ground Black Ground

Data 1 White Data 1

Data 0 Green Data 0

LEDCTL Brown LED Control

Tamper Purple Tamper

4. Trim and cover all unused conductors.

Note:

•The individual wires from the Reader are color-coded according

the Wiegand standard.

•When using a separate power supply for the Reader, this supply

and that of the Controller, must have a common ground.

•The Reader’s cable shield wire should preferably be attached

to an earth ground, or a signal ground connection at the panel,

or power supply end of the cable. This configuration is best for

shielding the Reader cable from external interference

Page 9 AY-Z12 Installation Manual

Table of contents

Rosslare AY-Z12 User manual

Popular Card Reader manuals by other brands