Ronix 2603 User manual
ELECTRIC DRILL PRESS 350W
2603
USER MANUAL 1
SPECIFICATIONS
Model 2603
Voltage 220-240V
Power 350W
Chuck Capacity 1.5-13mm
Drill Capacity
Steel:13mm
Wood: 20mm
Plastic 16mm
Spindle Travel 50mm
Class Of Speed 5
Speed 620-2620RPM
Spindle Taper B16
Distance from spindle axis to the
column 105mm
Distance from spindle end to the
surface of table 220mm
Distance from spindle end to the
surface of base 300mm
Swing 210mm
Table Size 160×160mm
Base Size 290×190mm
Column Diameter 46mm
Height 580mm
Net Weight/Gross Weight 15.5Kg
ELECTRIC DRILL PRESS
2
Accessories
SPRING WASHER 8 3
OUTSIDE HEX. BOLT M8x20 3
HANDLE & TIP 3
HEXAGON BAR WRENCH 3 1
HEXAGON BAR WRENCH 4 1
CROSS RECESS PAN HD SCREW M5 1
FLAT WASHER M5 1
PULLEY COVER TIP 1
CHUCK 1
CHUCK GUARD 1
OUTSIDE HEX. BOLT M10x35 4
BENCH VICE 2.5" 1
FLAT WASHER 10 8
NUT M10 4
PARTS LIST
Head assembly
Column
Table
Base
USER MANUAL 3
SPECIFICATIONS
WARNING!
To avoid electrical hazards, re hazards, or damage to the tool, use proper
circuit protection.
Use a separate electrical circuit for your tools. To avoid shock or re,
replace power cord immediately if it is worn, cut or damaged in any way.
WARNING!
To avoid mistakes that could cause serious injury, do not plug the Drill
Press in until you have read and understood the following.
1- READ and become familiar with the entire Operator’s Manual. LEARN
the tool’s application, limitations and possible hazards.
2- KEEP GUARDS IN PLACE and in working order.
3- REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of
checking to see that keys and adjusting wrenches are removed from the
tool before turning ON.
4- KEEP WORK AREA CLEAN. Cluttered areas and benches
invite accidents.
5- DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power
tools in damp or wet locations, or expose them to rain. Keep work area
well lighted.
6- KEEP CHILDREN AWAY. All visitors should be kept at a safe distance
from work area.
7- MAKE WORKSHOP CHILDPROOF with padlocks.
8- DON’T FORCE THE TOOL. It will do the job better and safer at the
rate for which it was designed.
9- USE THE RIGHT TOOL. Do not force tool or attachment to do a job
for which it was not designed.
10- USE PROPER EXTENSION CORD. Make sure your extension cord
is in good condition. When using an extension cord, be sure to use one
heavy enough to carry the current your product will draw. An undersized
cord will result in a drop in line voltage and in loss of power that will
ELECTRIC DRILL PRESS
4
cause the tool to overheat.
11- WEAR PROPER APPAREL. Do not wear loose clothing, gloves,
neckties, rings, bracelets, or other jewelry that may get caught in moving
parts. Non-slip footwear is recommended. Wear protective hair covering
to contain long hair.
12- ALWAYS WEAR EYE PROTECTION. Any Drill Press can
throw foreign objects into the eyes that could cause permanent
eye damage. ALWAYS wear Safety Goggles (not glasses). Everyday
eyeglasses have only impact-resistance lenses. They ARE NOT
safety glasses.
13- SECURE WORK. Use clamps or a vise to hold work when
practical. It’s safer than using your hand and it frees both hands to
operate tool.
14- DISCONNECT TOOLS before servicing; when changing
accessories such as blades, bits, cutters, and the like.
15- REDUCE THE RISK OF UNINTENTIONAL STARTING. Make
sure switch is in OFF position before plugging in.
16- USE RECOMMENDED ACCESSORIES. Consult the Operator’s
Manual for recommended accessories. The use of improper
accessories may cause serious injury.
17- NEVER STAND ON TOOL. Serious injury could occur if the
tool is tipped or if the cutting tool is unintentionally contacted.
18- CHECK FOR DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be carefully
checked to determine that it will operate properly and perform its
intended function – check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that is damaged
should be properly repaired or replaced.
19- NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
POWER “OFF”. Don’t leave tool until it comes to a complete stop.
20- DON’T OVERREACH. Keep proper footing and balance at all times.
21- MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean
USER MANUAL 5
for best and safest performance. Follow instructions for lubricating
and changing accessories.
22- Do not use power tools in the presence of ammable liquids or gases.
SAFETY
23- DO NOT OPERATE the tool if you are under the inuence
of any drugs, alcohol or medication that could affect your ability
to use the tool properly.
24- ALWAYS operate the Drill Press in a well-ventila ed area and
provide for proper dust removal. Use dust collection systems
whenever possible. Dust generated from certain materials can
be hazardous to your health.
SPECIFIC SAFETY INSTRUCTIONS
WARNING!
For your own safety, do not try to use your drill press or plug it in until it
is completely assembled and installed according to the instructions, and
until you have read and understood this instruction manual.
1- THIS DRILL PRESS is intended for use in dry conditions, indoor use only.
2- WEAR EYE PROTECTION. USE a face or dust mask along with safety
goggles if drilling operation is dusty. USE ear protectors, especially during
extended periods of operation.
3- DO NOT wear gloves, neckties, or loose clothing.
4- DO NOT try to drill material too small to be securely held.
5- ALWAYS keep hands out of the path of a drill bit. Avoid awkward
hand positions where a sudden slip could cause your hand to move into
the drill bit.
6- DO NOT install or use any drill bit that exceeds 175mm in length or extends
150mm below the chuck jaws. They can suddenly bend outward or break.
7- DO NOT USE wire wheels, router bits, shaper cutters, circle (y) cutters,
or rotary planers on this drill press.
8- WHEN cutting a large piece of material, make sure it is fully supported
at the table height.
ELECTRIC DRILL PRESS
6
9- DO NOT perform any operation freehand. ALWAYS hold the work
piece rmly against the table so it will not rock or twist. Use clamps or a
vise for unstable work pieces.
10- MAKE SURE there are no nails or foreign objects in the part of the
work piece to be drilled.
11- CLAMP THE WORKPIECE OR BRACE IT against the left side of
the column to prevent rotation. If it is too short or the table is tilted, clamp
it solidly to the table.
12- IF THE WORKPIECE overhangs the table such that it will fall or tip
if not held, clamp it to the table or provide auxiliary support.
13- SECURE THE WORK. Use clamps or a vise to hold the work
when practical. It’s safer than using your hand and it frees both hands
to operate tool.
14- MAKE SURE all clamps and locks are rmly tightened before drilling.
15- SECURELY LOCK THE HEAD and table support to the column, and
the table to the table support before operating the drill press.
16- NEVER turn your drill press ON before clearing the table of all
objects (tools, scraps of wood, etc.).
17- BEFORE STARTING the operation, jog the motor switch to make
sure the frill bit does not wobble or vibrate.
18- LET THE SPINDLE REACH FULL SPEED before starting to drill. If
your drill press makes an unfamiliar noise or if it vibrates excessively,
stop immediately, turn the drill press OFF and unplug. Do not restart the
unit until the problem is corrected.
19- DO NOT perform layout assembly or set up work on the table while
the drill press is in operation.
20- USE THE RECOMMENDED SPEED for any drill press accessory
and for different work piece material.
21- WHEN DRILLING large diameter holes, clamp the work piece rmly
to the table. Otherwise, the bit may grab and spin the work piece at high
speeds. DO NOT USE y cutters or multiple-part hold cutters, as they
can come apart or become unbalanced in use.
22- MAKE SURE the spindle has come to a complete stop before
USER MANUAL 7
touching the work piece.
23- TO AVOID INJURY from accidental starting, always turn the switch
OFF and unplug the drill press before installing or removing any
accessory or attachment or making any adjustment.
NOTE:
USE PROPER EXTENSION CORD. Make sure your extension
cord is in good condition. When using an extension cord,
be sure to use one heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in line voltage,
resulting in loss of power and cause overheating.
Be sure your extension cord is properly wired and in good condition.
Always replace a damaged extension cord or have it repaired by a
qualied person before using it.
Protect your extension cords from sharp objects, excessive heat
and damp or wet areas.
ASSEMBLY
.COLUMN SUPPORT TO BASE (FIG 1)
- Position the base on oor or bench.
-Place the column on the base, aligning the holes in the column
support with the holes in the base.
- Locate the four long hex bolts from the loose parts bag.
- Place a bolt in each hole through the column support and the
base. Tighten with an adjustable wrench.
.INSTALL TABLE (FIG 2)
Slide table assembly over column.
.TIGHTEN TABLE BRACKET LOCKING HANDLE TO SECURE TABLE
ASSEMBLY. (FIG 3)
ELECTRIC DRILL PRESS
8
.INSTALLING THE HEAD (FIG 4)
- Carefully lift the head above the column and slide it onto the column.
Make sure the head slides down over the column as far as possible.
Align the head with the base.
- Using the hex wrench, tighten the head lock set screws.
.INSTALLING FEED HANDLES (FIG 5)
Locate the three feed handles in the loose parts bag.
-Screw the feed handles into the threaded holes in the hub. Tighten.
.INSTALLING THE CHUCK (FIG 6)
WARNING!
Before any assembly of the chuck and arbor to the drill press head, clean
all mating surfaces with a non-petroleum based product; such as alcohol or
lacquer thinner. Any oil or grease used in the packing of these parts must
be removed; otherwise the chuck may come loose during operation.
- Open the jaws of the chuck by rotating the chuck sleeve clockwise. To
prevent damage, make sure the jaws are completely receded into the chuck.
- Push the chuck onto the spindle.
ATTENTION:
Clean the spindle taper with a non-alcohol based cleaner before
inserting it into the chuck.
- Using a wood mallet, rmly tap the chuck upward into position on
the spindle shaft.
USER MANUAL 9
.INSTALL KNOB AND SCREW OF UPPER PULLEY COVER. (FIG 7)
Fig1
Fig5
Fig2
Fig6
Fig3
Fig7
Fig4
ADJUSTMENT
.TABLE ADJUSTMENT
A. Tilting adjustment:
Loosen lock bolt then swing table to appropriate position and
retighten lock bolt.
B. Swing 360°
Loosen table bracket locking handle then swing table to appropriate
position and retighten the locking handle.
C. The scale of down shows work table’s degrees rotation
A B C
Table of contents
Other Ronix Power Tools manuals
