Ronda QM1 User manual
PROFESSIONAL INSTALLATION REQUIRED
Installation, Use & Care
Guide
Double Drawer/Cooler Units QM1
IL-MO-044 Rev. 1 04/2010
Double Drawer Unit – QM1
Insulated
Pag. 2 / 6
PROFESSIONAL INSTALLATION REQUIRED
Welcome & congratulations
Congratulations on your purchase of this double drawer.
We at Ronda are very proud of our product and we hope you consider us for fu-
ture purchases.
This product is made in our factory in Italy with components all made in Italy.
PLEASE READ CAREFULLY AND SAVE THESE INSTRUCTIONS
Packaging contents:
# 1 SMC Cabinet
# 2 Drawers
IL-MO-044 Rev. 1 04/2010
Double Drawer Unit – QM1
Insulated
Pag. 3 / 6
PROFESSIONAL INSTALLATION REQUIRED
Notes and Installation Tips
ALWAYS USE PROTECTION GLOVES AND EYE SAFETY GOGGLES:
Use care and always use protection gloves and safety goggles during in-
stallation and care. Because the drawers may have sharp edges, if not
handled with care they can cause cuts and abrasions.
Tools you will need : Power screw driver, manual screw driver, level, tape
measure.
Carefully unpack cabinets making sure not to scratch stainless steel fronts
and not to loose or misplace any components.
DO NOT remove polyethylene protective coating until installation is com-
plete.
Remove all drawers before installation. This will make cabinet easier to lift
and install and give access to installation hardware.
This product is made only for application on a subframe, which can be
made in different materials (wood, plastic, alluminium) into a wall structure
(Fig. 1)
Do not use the drawers as ladder. This would be dangerous for you and can
cause the item to break.
Fig. 1
a
b
Subframe
IL-MO-044 Rev. 1 04/2010
Double Drawer Unit – QM1
Insulated
Pag. 4 / 6
PROFESSIONAL INSTALLATION REQUIRED
Before Installation
Verify model number on the box label.
Verify the counter hole measure refering to the following table :
The maximum deviation permitted is : 0.04’’ (1 mm). Otherwise the SMC
panels get deformed and drawers don’t work properly. Use spacers to get
the right counter hole dimensions.
Checkwith a level that
Verify with a level the horizontal and vertical level of the counter hole and
correct if not accurate.
Counter Hole
Model a b
+0,04 + 0,04
inch
14.96
0
24.44
0
+1 +1
QM11
mm 380
0
621
0
IL-MO-044 Rev. 1 04/2010
Double Drawer Unit – QM1
Insulated
Pag. 5 / 6
PROFESSIONAL INSTALLATION REQUIRED
Assembly and Installation
1.
Carefully unpack cabinet making sure not to scratch stainless steel fronts.
Stainless is protected by a plastic coating that must be removed after
setup.
2.
Remove drawers and store in a safe place.
3.
Put the cabinet inside the counter
hole.
ATTENTION:
To correctly insert the cabinet , the slots
on the guides must be turned upward.
( see the foto down side )
IL-MO-044 Rev. 1 04/2010
Double Drawer Unit – QM1
Insulated
Pag. 6 / 6
PROFESSIONAL INSTALLATION REQUIRED
4.
Be sure that the cabinet fits well in
the wall.
No clearanceshould be left be-
tween the edges of the cabinet and
the wall.
If not, use spacers to fit.
5.
Secure the cabinet to the wall with
screws in the dedicated matching
holes in the cabinet.
Use # 12 mushroom head screws.
6.
Insert the drawer rear wheels into the guide slots.
IL-MO-044 Rev. 1 04/2010
Double Drawer Unit – QM1
Insulated
Pag. 7 / 6
PROFESSIONAL INSTALLATION REQUIRED
7.
Put the drawer forward,
than lift a bit to insert the
second wheel and put in-
side.
Close completely the
drawer.
8.
Repeatfor the second drawer
the operationfrom 6 to 7.
IL-MO-044 Rev. 1 04/2010
Double Drawer Unit – QM1
Insulated
Pag. 8 / 6
PROFESSIONAL INSTALLATION REQUIRED
Care and cleaning
It is imperative that the owner realizes that he/she is required to perform
reasonable maintenance and care of the drawers in order to maintain the
manufacturers warranty. Failure to perform reasonable maintenance and
care may void the warranty.
The following is a list of maintenance steps and things to avoid. This is not
intended to be a complete list, but is to be used as a guideline for general
care.
Carefully remove protective plastic peel coat from each stainless steel surface.
External Surfaces:
Clean stainless with stainless steel cleaner in direction of grain. Rubbing across
the grain direction may produce minor scratches. Recommended cleaners are
Weiman
©
, Stainless Steel Magic
©
and Sheila Shine
©
.
In a salty air environment, a slightly more oily cleaner like Sheila Shine
©
will pro-
tect better against oxidation, pitting or slight surface rust. Cleaning the surfaces
periodically will protect the finish for many years. In a heavily salty area, you will
have to clean more frequently as salt breaks down into highly corrosive chlorine
that will attack the metal. Surface corrosion will not affect performance of the
product, but will affect the look.
DO NOT USE scratchy pads, scouring pads, or stiff sponges for cleaning. Do not
use abrasive detergents, powdered cleansers or detergents containing acid sub-
stances or bleach.
IL-MO-044 Rev. 1 04/2010
Double Drawer Unit – QM1
Insulated
Pag. 9 / 6
PROFESSIONAL INSTALLATION REQUIRED
Internal surfaces:
Clean the internal surface of the cabinet use warm water and soap.
Wash after each use and dry to avoid formation of molds and staining.
The cabinet’s working surface are constructed from Sheet Moulding Coumpound
(SMC), a glass rinforced polyester resin resistent to corrosion.
Removing and cleaning the magnetic gasket :
•Carefullyinsertascrewdriverinto acornerof
thegasket(1).
•Liftthegasket untilitexitsfromtheseat(2).
•Removethegasketbyhand (3).
•Cleanwithwater andneutraldetergent.
•Insert the gasket inits seat andstrongly
pressitonalltheperimeter.Youcanlubri-
catethegasketseattodothiseasly.
Drawer Guides
Drawer load capacity should not exceed 50 lbs per drawer. Never use an ex-
tended drawer for a ladder or a work platform.
1
2
3
IL-MO-044 Rev. 1 04/2010
Double Drawer Unit – QM1
Insulated
Pag. 10 / 6
PROFESSIONAL INSTALLATION REQUIRED
WARNINGS
•Surfaces can be very hot when exposed to direct sunlight.
•Molds can form if not properly dried.
•Do not use as a ladder.
•Avoid any contact with electrical outlets or wires.
•This is only a food container. It is not a refrigerated space,
and will not prevent food spoilage.
•If exposed to temperatures below – 4 °F and above + 120 °F
deformation and malfunction of the drawers can occur.
•If installed adjacent to the heating elements of a barbeque,
insulation can be less effective.
•If installed near to the sea, damage from salty water can oc-
cur.
•Keep drawers closed when not in use.
Table of contents
Other Ronda LCD Drawer manuals
Popular LCD Drawer manuals by other brands
Acnodes
Acnodes KD 8228 user manual
Ameriwood
Ameriwood 9524328PCOM manual
Kesseböhmer
Kesseböhmer TANDEM solo Mounting instructions
Crystal Image Technologies
Crystal Image Technologies RMD-151-A Series user manual
APW Wyott
APW Wyott Ease Extreme HDX-1-120 Installation and operating instructions
NTI
NTI RACKMUX-V17-N Installation and operation manual
GRASS
GRASS DWD XP manual
StarTech.com
StarTech.com DuraView RACKCONS1701 instruction manual
Fisher & Paykel
Fisher & Paykel IZONA CoolDrawer RB36S installation instructions
Synergy Global Technology
Synergy Global Technology LCD1U17-44 user manual
Fujitsu
Fujitsu RC25 user manual
Acnodes
Acnodes RK 1000B installation guide