Ronda QK1 User manual
PROFESSIONAL INSTALLATION REQUIRED
Installation, Use & Care
Guide
Single Drawer / Cooler QK1
IL-MO-047 Rev. 1 04/2010
Single Drawer - QK1
Cooler
Pag. 2 / 12
PROFESSIONAL INSTALLATION REQUIRED
1
2
Welcome & congratulations
Congratulations on your purchase of this double drawer.
We at Ronda are very proud of our product and we hope you consider us for
future purchases.
This product is made in our factory in Italy with components all made in Italy.
For any questions contact us at : info@ronda.it
PLEASE READ CAREFULLY AND SAVE THESE INSTRUCTIONS
Packaging contents:
# 1 SMC Cabinet
# 1 Drawer
IL-MO-047 Rev. 1 04/2010
Single Drawer - QK1
Cooler
Pag. 3 / 12
PROFESSIONAL INSTALLATION REQUIRED
Notes and Installation Tips
ALWAYS USE PROTECTION GLOVES AND EYE SAFETY
GOGGLES: Use care and always use protection gloves and safety
goggles during installation and care. Because the drawers may have
sharp edges, if not handled with care they can cause cuts and
abrasions.
Tools you will need : Power screw driver, manual screw driver, level,
tape measure.
Carefully unpack cabinets making sure not to scratch stainless steel
fronts and not to loose or misplace any components.
DO NOT remove polyethylene protective coating until installation is
complete.
Remove the drawer before installation. This will make cabinet easier to
lift and install and give access to installation hardware.
This product is made only for application on a subframe, which can be
made in different materials (wood, plastic, alluminium) into a wall
structure (Fig. 1)
Do not use the drawer as ladder. This would be dangerous for you and
can cause the item to break.
Fig. 1
a
b
Subframe
IL-MO-047 Rev. 1 04/2010
Single Drawer - QK1
Cooler
Pag. 4 / 12
PROFESSIONAL INSTALLATION REQUIRED
Before Installation
Verify model number on the box label.
Verify the counter hole measure refering to the following table :
The maximum deviation permitted is : 0.04’’ (1 mm). Otherwise the
SMC panels get deformed and drawers don’t work properly. Use
spacers to get the right counter hole dimensions.
Check with a level that wall is plumb.
Verify with a level the horizontal and vertical level of the counter hole
and correct if not accurate.
Counter Hole
Model a b
+0,04 + 0,04
inch
14.96
0
11,45
0
+1 +1
QK11
mm 380
0
291
0
IL-MO-047 Rev. 1 04/2010
Single Drawer - QK1
Cooler
Pag. 5 / 12
PROFESSIONAL INSTALLATION REQUIRED
Assembly and Installation
1.
Carefully unpack cabinet making sure not to scratch stainless steel fronts.
Stainless is protected by a plastic coating that must be removed
after setup.
2.
Remove drawers and store in a safe place.
3.
Put the cabinet inside the counter
hole.
ATTENTION:
To correctly insert the cabinet , the slots
on the guides must be turned upward. (
see the foto down side )
IL-MO-047 Rev. 1 04/2010
Single Drawer - QK1
Cooler
Pag. 6 / 12
PROFESSIONAL INSTALLATION REQUIRED
4.
Be sure that the cabinet fits well in
the wall.
No clearanceshould be left
between the edges of the cabinet
and the wall.
If not, use spacers to fit.
5.
Secure the cabinet to the wall with
screws in the dedicated matching
holes in the cabinet.
Use # 12 mushroom head screws.
6.
Insert the drawer rear wheels into the guide slots.
IL-MO-047 Rev. 1 04/2010
Single Drawer - QK1
Cooler
Pag. 7 / 12
PROFESSIONAL INSTALLATION REQUIRED
7.
Put the drawer forward, than
lift a bit to insert the second
wheel and put inside.
Close completely the
drawer.
IL-MO-047 Rev. 1 04/2010
Single Drawer - QK1
Cooler
Pag. 8 / 12
PROFESSIONAL INSTALLATION REQUIRED
Care and cleaning
It is imperative that the owner realizes that he/she is required to perform
reasonable maintenance and care of the drawers in order to maintain
the manufacturers warranty. Failure to perform reasonable
maintenance and care may void the warranty.
The following is a list of maintenance steps and things to avoid. This is
not intended to be a complete list, but is to be used as a guideline for
general care.
Carefully remove protective plastic peel coat from each stainless steel
surface.
External Surfaces:
Clean stainless with stainless steel cleaner in direction of grain. Rubbing
across the grain direction may produce minor scratches. Recommended
cleaners are Weiman
©
, Stainless Steel Magic
©
and Sheila Shine
©
.
In a salty air environment, a slightly more oily cleaner like Sheila Shine
©
will
protect better against oxidation, pitting or slight surface rust. Cleaning the
surfaces periodically will protect the finish for many years. In a heavily salty
area, you will have to clean more frequently as salt breaks down into highly
corrosive chlorine that will attack the metal. Surface corrosion will not affect
performance of the product, but will affect the look.
DO NOT USE scratchy pads, scouring pads, or stiff sponges for cleaning. Do
not use abrasive detergents, powdered cleansers or detergents containing
acid substances or bleach.
IL-MO-047 Rev. 1 04/2010
Single Drawer - QK1
Cooler
Pag. 9 / 12
PROFESSIONAL INSTALLATION REQUIRED
Internal surfaces:
Clean the internal surface of the cabinet use warm water and soap.
Wash after each use and dry to avoid formation of molds and staining.
The cabinet’s working surface are constructed from Sheet Moulding
Coumpound (SMC), a glass rinforced polyester resin resistent to corrosion.
Removing and cleaning the magnetic gasket :
•Carefullyinsertascrewdriver intoacornerof
thegasket(1).
•Liftthegasketuntilitexits fromtheseat(2).
•Removethegasketbyhand(3).
•Cleanwithwaterandneutraldetergent.
•Insert the gasket inits seat andstrongly
press itonalltheperimeter.Youcan
lubricatethegasketseattodothiseasly.
Drawer Guides
Drawer load capacity should not exceed 50 lbs per drawer. Never use an
extended drawer for a ladder or a work platform.
1
2
3
IL-MO-047 Rev. 1 04/2010
Single Drawer - QK1
Cooler
Pag. 10 / 12
PROFESSIONAL INSTALLATION REQUIRED
WARNINGS
•Surfaces can be very hot when exposed to direct sunlight.
•Molds can form if not properly dried.
•Do not use as a ladder.
•Avoid any contact with electrical outlets or wires.
•This is only a food container. It is not a refrigerated space,
and will not prevent food spoilage.
•If exposed to temperatures below – 4 °F and above + 120
°F deformation and malfunction of the drawers can o ccur.
•If installed adjacent to the heating elements of a barbeque,
insulation can be less effective.
•If installed near to the sea, damage from salty water can
occur.
•Keep drawers closed when not in use.
Table of contents
