Rompa NFINITY & BEYOND User manual
Page 1of 18 Copyright ROMPA® Ltd
INFINITY & BEYOND 20565, KH 4.11
INFINITY & BEYOND 20565
DESCRIPTION
There are 64 multi-coloured LEDs on an acrylic backed mirror in this panel. They shine onto
a one-way mirror and their light is reflected back to give an impression of infinity. At the
bottom of the panel is a ¼”/6.3mm jack socket B. If a switch terminated in a jack plug is
inserted into the socket the display can be controlled via the external switch. A One Button
Switch Box is included but further switches can be purchased separately – see
www.rompa.com for an extensive range of switches.
NOTE: Only suitable switches should be used in conjunction with the Infinity & Beyond.
Radios, amplifiers or other equipment terminated in jack plugs should never be connected.
Damage to the electronics of either or both items is likely to follow. Similarly a hand held
microphone must not be plugged straight into this product.
Page 2of 18 Copyright ROMPA® Ltd
INFINITY & BEYOND 20565, KH 4.11
CONTENTS
1 x Infinity & Beyond Panel
1 x Removable Control Box
1 x One Button Switch Box
NOTE: No fixings are included for wall mounting (please seek professional advice regarding
construction of wall – see below).
Page 3of 18 Copyright ROMPA® Ltd
INFINITY & BEYOND 20565, KH 4.11
TO WALL MOUNT PANEL
IMPORTANT: This panel weighs approximately 21 kg. Please take this into consideration
when fixing. Please make sure that you are aware of the construction of the wall the panel is
to be fixed to. Taking this into account please ensure that you use the correct fittings.
1. Attach fixings such as mirror plates to the back of the panel. Fixings are not supplied as
these depend on the surface the panel will be fixed to. Check the fixings e.g. mirror plates
you buy can easily support 21kg. You may wish to attach two mirror plates to the back of
the panel at the top and two on the back at the bottom.
Note: When attaching fixings to the back of the panel please proceed with caution – be aware
that there are electrical assemblies inside the panel.
TO OPERATE
1. Plug in to mains supply. Switch on using the rocker switch at the top of the panel. The
display will light up immediately.
2. Connect the Removable Control Box to the socket on the top of the panel – this will be
located near to the switches shown above.
3. Connect the One Button Switch Box to the jack socket on the lower half of the panel as
required. Another compatible simple switch could be connected to this jack socket e.g.
Soft Koosh Switch 19966.
3. There are four buttons on the Control Box. These have the following functions:
Red button with a swirl – pattern selection
There are 49 LED effects to choose from.
These are:
1. All the LEDs in both circles are illuminated and the colours rotate (2 LEDs at a time) in
sequence, showing full circles. The display is multi-coloured - red, green, blue and
purple. The rotation is clockwise.
2. All the LEDs in both circles are illuminated, showing full circles. The display is red only.
The LEDs appear to rotate.
3. All the LEDs in both circles are illuminated, showing full circles. The display is green only.
The LEDS appear to rotate.
Page 4of 18 Copyright ROMPA® Ltd
INFINITY & BEYOND 20565, KH 4.11
4. All the LEDs in both circles are illuminated, showing full circles. The display is blue only.
The LEDS appear to rotate.
5. All the LEDs in both circles are illuminated, The display is multi-coloured – red, green,
blue, pale blue, yellow, orange, purple. The LEDs rotate, one LED at a time.
6. As 2., but in the opposite direction.
7. As 3., but in the opposite direction.
8. As 4., but in the opposite direction.
9. The display is multi-coloured – red, green, blue, purple. Both circles are displayed in full.
The effect is rotating clockwise, 2 LEDs at a time.
10. All the LEDs in both circles are illuminated, mostly in red, with 3 green LEDs rotating anti-
clockwise in sequence.
11. All the LEDs in both circles are illuminated, mostly in green, with 3 red LEDs rotating anti-
clockwise in sequence.
12. All the LEDs on both circles are illuminated, mostly in blue, with 3 yellow LEDs rotating
anti-clockwise in sequence.
13. The effects of 10., but clockwise.
14. The effects of 11.,but clockwise.
15. The effects of 12., but clockwise.
16. Only the LEDS in the bottom circle are illuminated. The LEDs are red, with 4 LEDs in
green, rotating in sequence in an anti-clockwise direction.
17. Only the LEDs in the bottom circle are illuminated. The LEDs are green, with 4 LEDs in
red, rotating in sequence in an anti-clockwise direction.
18. Only the LEDs in the bottom circle are illuminated. The LEDs are blue, with 4 LEDs in
yellow, rotating in an anti-clockwise direction.
19. Only the LEDs in the bottom circle are illuminated. There are red, green, white LEDs
rotating in sequence in an anti-clockwise direction.
20. As 16., but the display moves clockwise.
21. As 17., but the display moves clockwise.
22. As 18., but the display moves clockwise.
23. As 19., but the display moves clockwise.
24. Only the LEDs in the upper circle are illuminated. The LEDs are red, with 4 LEDs in
green rotating in an anti-clockwise direction.
25. Only the LEDs in the upper circle are illuminated. The LEDs are green, with 4 LEDs in
red, rotating in an anti-clockwise direction (see right).
26.Only the LEDs in the upper circle are illuminated. The LEDs are blue, with 4 LEDs in
yellow, rotating in an anti-clockwise direction.
27.Only the LEDs in the upper circle are illuminated. There are 4 red, 4 green, 4 red, 4 green
LEDs and so on, rotating in an anti-clockwise direction.
28.As 24., but the display moves clockwise.
29.As 25., but the display moves clockwise.
30.As 26., but the display moves clockwise.
31.Only the LEDs in the upper circle are illuminated – 4 red LEDs then 4 green, then 4 red
etc, moving clockwise.
32.The LEDs outlining the joined circles are illuminated. The overlap of the circles is not
illuminated. The display is red only.
33.As 32., but in green only.
34.The LEDs outlining the joined circles are illuminated. The overlap of the circles is not
illuminated. The LEDs are multi-coloured (yellow, red, purple, blue, orange etc) – the
colours rotate in sequence.
35.The LEDs outlining the joined circles are illuminated. The overlap of the circles is not
illuminated. The LEDs are alternately one red, one green, one red, one green etc – the
colours rotate in sequence.
Page 5of 18 Copyright ROMPA® Ltd
INFINITY & BEYOND 20565, KH 4.11
36.The LEDs outlining the joined circles are illuminated. The overlap of the circles is not
illuminated. The LEDs are green – the colours rotate in a sequence: 2 LEDs ON, 2 LEDs
OFF.
37.The LEDs outlining the joined circles are illuminated. The overlap of the circles is not
illuminated. The LEDs are multi-coloured and rotating in sequence.
38.As 35., but in an anti-clockwise direction.
39.One red LED moves around the outline of both circles, in an anti-clockwise direction.
40.As 39, but green.
41.As 39, but blue.
42.Starting in the bottom circle, the number of illuminated LEDs increases by one. Once the
full figure of eight is illuminated, the number of LEDs decreases by one. The display is
red, and moves in an anti-clockwise direction.
43.As 42., but the display is green.
44.The display is red, with 4 green LEDs in each circle, rotating anti-clockwise in sequence.
45.The display is green, with 4 red LEDs in each circle, rotating anti-clockwise in sequence.
46.The outline of the 2 circles is purple, with green LEDs in the central oval where the two
circles overlap. Within this central oval, two red dots rotate in sequence.
47.The outline of the 2 circles is green, with blue LEDs in the central oval where the two
circles overlap. Within this central oval, two red dots rotate in sequence.
48.The outline of the 2 circles is green, with blue LEDs in the central oval where the two
circles overlap. Within this central oval, four red dots rotate in sequence.
49.All the LEDs are illuminated in a single colour, with the pattern rotating. After
approximately 6 seconds, the colour changes. The colour sequence is typically red,
green, blue, yellow, purple, white (light blue), turquoise, orange and back to red.
In Mode 2, press the round button at the top of the panel to stop and start one of the 49 LED
effects. Alternatively connect a switch via the jack socket in the bottom of the panel. Activate
the switch to stop and start the chosen LED effect.
Speed Button (green button with lightning flash)
There are 12 speed options available. Each touch of this button will
make the LED effects move more quickly. After the twelfth option,
the speed options will start again at the slowest option.
Stop/Start button (blue button with 2 vertical lines)
Use this pattern to stop and start the rotation of the LED effect.
Page 6of 18 Copyright ROMPA® Ltd
INFINITY & BEYOND 20565, KH 4.11
Sound Effects (yellow button with musical notes)
Press this button to activate a sound effect at any time. There are
4 sounds which play in the same order. Use the Volume button at
the top of the panel to adjust the volume.
When the panel is switched off after use, the panel; will ‘remember’ the last volume setting
chosen. The Volume button can be either pressed repeatedly or held down to adjust the
volume setting.
The above controls have a round socket above them for the Removable Control Box with Panel 20565.
Modes
Mode 1: The first pattern is repeated continuously till the Pattern button is pressed, or until the
connected switch box top is pressed. The Stop/Start button can be used in this mode.
Mode 2: Automatic pattern change. The pattern changes when the Red button with the swirl
is pressed, or after several cycles. How quickly the several cycles is completed depends on
the speed chosen with the Speed Button. The Stop/Start button can be used in this mode.
Mode 3: Infinity & Beyond will light up the next LED with every touch of the Stop/Start button
(or an external switch connected via jack socket). That is to say that where as Modes 1 and 2
move between effects, Mode 2 remains on the same effect, but moves the LEDs along in
sequence.
To change between modes:
The panel starts up in whichever mode it has been set to.
To choose Mode 2, press the top rocker switch at the top of the panel till it is in the central
position.
To choose Mode 3, press top rocker switch till it is on Mode 3.
Switch off after use.
Page 7of 18 Copyright ROMPA® Ltd
INFINITY & BEYOND 20565, KH 4.11
Wi Fi Operation
This panel is also part of ROMPA®’s extensive Wi Fi range. This means that the colour of the
display can be controlled using any one of ROMPA®’s Wi Fi controllers. These include:
Wi Fi Microphone 20563
For sound-responsive wireless control of your ROMPA®Infinity &
Beyond Panel, choose this fantastic microphone. With each sound
made into the microphone, the intensity of the colour of the display
may be changed, or change the colour altogether.
Talking Cubes 18870 and 20402
Throw the cube like a die to wirelessly change the colour of the
display, and hear your pre-recorded messages!
Wi Fi Interactive Carpet Switch Set 19939
Walk on the nine textured mats to change the colour of the
display. Alternatively, wall-mount the mats for a colourful
and interactive wall!
Colour Changing Panel 19214
Wirelessly controls colours and the intensity of colours of your Infinity &
Beyond.
8 Colour Wirefree Controller 19847
With 9 interactive buttons and 9 jack sockets
to add your own switches
Page 8of 18 Copyright ROMPA® Ltd
INFINITY & BEYOND 20565, KH 4.11
These Wi Fi controllers can be used with your Infinity & Beyond, and a whole host of other
compatible ROMPA®products so whole environments can be remotely colour-controlled.
These products include bubble tubes, light sources, Milky Way carpets, Star Cloths, Wi Fi
Starry Sky Panel, Light Diffraction Totem, many Wall panels …
This panel can also be used as part of an everysense®environment to switch your favourite
Snoezelen®products ON and OFF and to control imagery, products, light and sounds as well
as colour.
Contact us for further information.
Page 9of 18 Copyright ROMPA® Ltd
INFINITY & BEYOND 20565, KH 4.11
SAFETY
Always supervise the use of this product.
For indoor use only.
In the unlikely event of product failure this panel will automatically shut down. Please seek
advice – only a suitably qualified person should attempt repair.
CARE & MAINTENANCE
Since this product uses LEDs not lamps, and LEDs last several thousand hours, it is
extremely unlikely that the LEDs will need replacing.
Once this product is eventually exhausted, please dispose of it appropriately.
TROUBLESHOOTING
In the unlikely event of product failure, please check the following:
•Has the product been plugged in and switched on at the wall?
•Check the fuse in plug
•If the front cover has been removed, it is possible that removal has dislodged the small
black box that is connected to both the jack socket (visible from the front) and the back
of the front cover. Attached to this small black box is a plug from the transformer – this
plugs into the small black box. Check that this has become detached. Check all
connections are properly connected.
SPECIFICATION
Power Supply: 230V 50 Hz
(110/120V for US) 60 Hz
Output: 12V DC 5A
5A fuse in mains plug (UK)
LEDs: 64 x multi-colour, high brightness (-90mcd) 10mm diameter, 50 degree viewing angle
The panel cover is phthalate-free
Page 10 of 18 Copyright ROMPA® Ltd
INFINITY & BEYOND 20565, KH 4.11
PAINEL INTERACTIVO INFINITO 20565
DESCRIÇÃO
Existem 64 LEDs multicoloridos num espelho escuro neste painel. Eles brilham num espelho
de um sentido e a sua luz é reflectida dando a sensação de infinito. No fundo do painel tem
uma ligação Jack de 6.3mm B. Se ligar um switch nessa entrada, o visor pode ser controlado
através do switch externo. Está incluído um switch de um botão, mas pode comprar mais
switches separadamente – visite www.rompa.com para consultar uma extensa gama de
switches.
NOTA: Apenas switches adequados podem ser utilizados em conjunto com o painel infinito.
Rádios, amplificadores e outros equipamentos com ligações Jack nunca devem ser ligados
na entrada Jack. Se o fizer, podem ocorrer danos nos componentes electrónicos de ambos
os aparelhos. Também não deve ligar nesta entrada qualquer tipo de microfone.
This manual suits for next models
1
Table of contents
Languages:
Other Rompa Lighting Equipment manuals
Rompa
Rompa 17630 User manual
Rompa
Rompa Light & Music Dome User manual
Rompa
Rompa Maxi Ball-Bubble Tube User manual
Rompa
Rompa 22970 User manual
Rompa
Rompa 19723 User manual
Rompa
Rompa Linelite 18540 User manual
Rompa
Rompa Waterless Rainbow Tube User manual
Rompa
Rompa 14532 User manual
Rompa
Rompa 19209 User manual
Rompa
Rompa 19280 User manual
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
