Roland monoFabARM-10 User manual
User’s Manual
2
Introduction
Thank you very much for purchasing this product.
• To ensure correct and safe usage with a full understanding of this product’s performance, please be sure to read through this manual completely and store it in
a safe location.
• Unauthorized copying or transferral, in whole or in part, of this manual is prohibited.
• The contents of this operation manual and the specications of this product are subject to change without notice.
• The operation manual and the product have been prepared and tested as much as possible. If you nd any misprint or error, please inform us.
• Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur through use of this product, regardless of any failure to
perform on the part of this product.
• Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur with respect to any article made using this product.
Company names and product names are trademarks or registered trademarks of their respective holders.
http://www.rolanddg.com/
Copyright © 2014 Roland DG Corporation
Roland DG Corp. has licensed the MMP technology from the TPL Group.
3
Contents
Introduction ..................................................2
Contents .....................................................3
Features of this Machine ......................................4
Important Notes on Handling and Use.........................5
Modeling Machine ......................................5
Photo-curable Resin .....................................6
Part Names ...................................................7
Basic Operation...............................................9
How to Start the Machine ................................9
How to Shut Down the Machine ....................... 11
Output (Printing) ........................................... 12
Operation Flow........................................ 12
Create 3D Data and Convert it to STL Format ........... 13
Import STL data using monoFab Player AM ............. 14
Prepare for Printing .................................... 20
Output data and start printing ......................... 27
Post-print processing .................................. 32
Maintenance ............................................... 35
Perform Maintenance after Use ........................ 35
Periodic Maintenance.................................. 41
Replace Consumable Parts ............................. 42
Appendix................................................... 43
What to Do If .......................................... 43
When Moving the Machine ............................ 48
Main Specications .................................... 50
4
Features of this Machine
Layered projection technology printing
The monoFab ARM-10 is a 3D printer that uses layered projection technology.
It employs photo-curable resin (referred to simply as “resin” in this manual), a uid that hardens (cures) when exposed to light (UV rays),
and a projector with a UV LED light source to print an object based on 3D data.
"“OperationFlow” (p. 12)
The advantages of using the layer exposure method to print objects one layer at a time
The printing method whereby print data is sliced into layers at regular intervals, each of which is exposed (irradiated with light) by a
projector one layer at a time, is referred to as the layer exposure method.
This printing method makes it possible to print multiple jobs simultaneously and to print complex shapes with undercuts.
"“PrintMultipleObjectsSimultaneously” (p. 17)
monoFab Player AM - A dedicated output program that can be used to start printing immediately
monoFab Player AM is a dedicated program for outputting 3D data in STL format to the ARM-10.
monoFab Player AM can be downloaded from the following web page:
"“RolandDGStart-uppage” (http://startup.rolanddg.com/)
5
Important Notes on Handling and Use
Be sure to observe the following important points. Failure to observe them may not only result in loss of performance, but may also cause malfunction or
breakdown.
Modeling Machine
This machine is a precision device
• Handle carefully, and never subject the machine to impact or excessive force.
• Use within the range of specications.
• Never attempt to move the Z axis unit by hand with undue force.
• Never needlessly put your hand or ngers inside the cover, or other internal areas of the machine.
Install in a suitable location
• Never install in a location exposed to direct sunlight.
• Install in a location having the specied temperature and relative humidity.
Installation
Environment
Operating Temperature of 20 to 30°C, 68 to 86°F, 35 to 80% relative humidity (no condensation)
Not operating Temperature of 5 to 40°C, 41 to 95°F, 20 to 80% relative humidity (no condensation)
• Install in a quiet, stable location oering good operating conditions.
This machine becomes hot.
• Install in a well-ventilated location.
Do not let children use the machine unsupervised and do not keep in the reach of infants.
• To avoid the swallowing of small parts and the like, do not keep the machine in the reach of infants.
• Do not let children play with any plastic bag used for packaging. Putting a bag over one’s head or ingesting it could result in suocation.
Important Notes on Handling and Use
6
Photo-curable Resin
Handling of photo-curable resin
• When handling photo-curable resin, wear gloves and do not let it come into contact with skin.
• If photo-curable resin gets on the skin, wash thoroughly with soap.
• If photo-curable resin gets on the machine, wipe it o using a rag soaked with ethanol.
Handling of photo-curable resin containers
• Never drop or shake forcefully. Failure to do so may result in resin leakage.
Storage
• The expiration date for photo-curable resin is one year from the date of manufacture shown on the photo-curable resin container.
• Store photo-curable resin away from direct sunlight or strong lighting.
• Store in a well-ventilated area between 5°C and 40°C.
• Always close the lid securely when storing a photo-curable resin container. Failure to do so may result in resin leakage.
Disposal
• Do not return used photo-curable resin to the photo-curable resin container.
• Transfer excess resin after printing to a transparent container, let it cure, and then dispose of it according to local waste sorting criteria. (Do not dispose of resin
in sewage systems or rivers.)
7
Part Names
Exterior
1
4
5
2
3
Number Name Explanation
1Front cover
Before starting operation and during operation, close
the front cover.
* The front cover is orange to make it dicult for UV
rays to pass through.
2[ ] (Power) button (p. 9)
3Rubber feet (x4, with height
adjustment screws) Used to adjust the angle of the ARM-10.
4
Power-cord connector
WARNING
Do not use with any electrical power supply that does not meet the ratings
displayed on the AC adapter.
Doing so may lead to re, electrical shock, or electrocution.
WARNING
Never use any AC adapter or power cord other than those included with the
machine.
Doing so may lead to re, electrical shock, or electrocution.
WARNING
Handle the AC adapter, power cord, plug, and electrical outlet correctly and with
care. Never use any article that is damaged.
Using a damaged article may result in re or electrical shock.
5
USB connector
CAUTION
For the USB cable, use the included cable.
The computer may not be able to communicate with the computer correctly.
Part Names
8
Inside the Front Cover
1
2
6
7
8
9
11
10
3
4
5
Number Name Explanation
1Z axis unit (inside red box) The device that moves the printing
platform.
2Printing platform handle Used to install and remove the printing
platform.
3Shutter lever
By installing the liquid material vat,
the UV irradiation outlet shutter on
the bottom of the liquid material vat is
opened.
4UV irradiation outlet (with shutter) When the shutter opens, UV rays are
emitted from the machine.
5Liquid material vat stopper
Secures the liquid material vat in place.
When the stopper is disengaged, the
liquid material vat moves toward you.
6Printing platform retaining screw The screw that secures the printing
platform.
7Z0 adjustment screw
When setting the initial printing height
(Z0), loosen the Z0 adjustment screws
(p. 24).
8Printing platform
The part on which the job is created.
The job is printed while the printing
platform is raised.
9Liquid material vat The container to which resin for
modeling is added.
10 Liquid material vat retaining screws Screws for securing the liquid material
vat holder.
11 Liquid material vat holder Screws for securing the liquid material
vat.
9
Basic Operation
How to Start the Machine
1.Close the front cover.
2.Press the [](Power) button on the ARM-10.
The ARM-10 turns on and initialization starts. The [](Power) button will start ashing slowly.
When the ARM-10 nishes initialization, the [](Power) button stops ashing and remains steadily lit.
3.Start monoFab Player AM.
Windows 8.1 users
1.On the [Start] screen, click .
2.On the [Apps] screen, click [monoFabPlayerAM].
Basic Operation
10
Windows 8 users
1.Right-click the [Start] screen.
2.Click the [Allapps] icon.
3.Under [monoFabPlayerAM], click the [monoFabPlayerAM] icon.
Windows 7 / Windows Vista users
1.Click the [Start] button .
2.Click [Allprograms] (or [Programs]).
3.Under [monoFabPlayerAM], click the [monoFabPlayerAM] icon.
Table of contents
Other Roland 3D Printer manuals
