Rocktron Cyborg User manual

Your Cyborg™Digital Reverb pedal has been designed to comply with the

following Standards and Directives as set forth by the European Union:

Council Directive(s): 89/336/EEC Electromagnetic Compatibility

Standard(s): EN55013, EN50082-1

This means that this product has been designed to meet stringent guide-

lines on how much RF energy it can emit, and that it should be immune from

other sources of interference when properly used. Improper use of this

equipment could result in increased RF emissions, which may or may not

interfere with other electronic products.

To insure against this possibility, always use good shielded cables for all

audio input and output connections. This will help insure compliance with

the Directive(s).

For more information about other Rocktron products, please see your local

dealer or one of our importers closest to you (listed on the Rocktron website

- www.rocktron.com).

Precautions

Read all instructions contained in this manual.

Keep these instructions

Heed all warnings

Follow all instructions.

Do not use this apparatus near water.

Clean with dry cloth

Do not block any ventilation openings (if applicable). Install in accordance with the

manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, stoves or other

apparatus (including amplifiers) that produce heat.

This product is supplied with and runs on a 9VDC adapter.

Only used attachments/accessories specified by the manufacturer.

Do not use this product with any case, stand tripod, bracket or table that is not

specified by the manufacturer. Insure that the case, stand, tripod, bracket etc. is

properly adjusted and setup (follow all instructions). Extra care and caution should

be taken to avoid tip over and injury.

Unplug this apparatus during lightning storms or when unused during long periods

of time.

Refer all service to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power supply or plug is damaged,

liquid has been spilled or objects have fallen into the apparatus or if the apparatus

has been exposed to rain or moisture, does not operate normally or has been

dropped.

DO NOTATTEMPTTO SERVICE THIS EQUIPMENT. QUALIFIED PERSON-

NELSHOULD SERVICE THIS EQUIPMENT ONLY. DO NOT MAKEANY

INTERNALADJUSTMENTS OR ADDITIONS TO THIS EQUIPMENTATANY

TIME OR TAMPER WITH INTERNAL ELECTRONIC COMPONENTSATANY

TIME. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY VOID THE

WARRANTY OF THIS EQUIPMENT AS WELLAS CAUSING A SHOCK

HAZARD.

OPERATINGTEMPERATURE

Do not expose this unit to excessive heat. This unit is designed to operate between

32 F and 104 F (0 C and 40 C). This unit may not function properly under extreme

temperatures.

Precautions Continued....

Introduction

Congratulations on your purchase of the Rocktron

Cyborg Digital Reverb.

The Cyborg Digital Reverb is one of a series of “Digital

Destiny” stomp boxes that break new ground in the

world of floor effects excellence. Simple to use, while

offering instant access effects, or satisfying those who

crave more complex control and the ability to create a

plethora of additional presets, the Cyborgs are low

noise, easy operation effects!

Rocktron has designed the Cyborg series around a

state-of-the-art Motorola® DSP engine. We’ve included

our HUSH® noise reduction technology, and provided

you with full bandwidth performance. We’ve cut no

corners in the design of these digital stomp boxes.

Cyborgs are fully MIDI programmable and controllable

and Cyborgs can be chained together and controlled by

a single Rocktron MIDI controller.

Look for other Cyborg Digital Destiny pedals at your

Rocktron retailer.

Connection 1 - Standard Connection

Connection 2 - Effects Loop

Connection 3 - with a Noisy Distortion Pedal

Preset Select Knob - this knob allows you to select the “preset” you desire.

Eight presets are available with this control. As the knob is turned the LED

under the selected preset will light.

LED Display - see following page for detailed descriptions of display.

Reverb TYPE Knob - this knob allows you to select one of the 8 available

reverbs, Plate A, Plate B, Room A, Room B HallA, Hall B, Stadium, and

Dual. As you turn the knob you will note that the LEDs in the LED display

will light as you scroll through the different reverbs available as shown in the

Reverb Type line in the LED display (for more information the LED display,

see the following page).

Decay Knob - this knob allows you to adjust the decay of the reverb tail. As

you turn the knob you will note that the LEDs in the LED display will light in

order from left to right as you increase the amount of decay. As you decrease

the amount of decay the LEDs will turn off from right to left.

Level Knob - this knob determines the “volume” of the reverb relative to the

dry signal. As you increase the reverb volume the LEDs in the LED display

will light in order from left to right and stay lit. As you decrease the volume of

the delay the LEDs will turn off from right to left.

DC OnTap Power input. Use the supplied Rocktron DC OnTap 9V adapter

to power your Cyborg pedal. Plug into a standard wall outlet and follow all

safety precautions.

Input Jack - plug your guitar into this jack. See preceeding pages for

standard connections.

HUSH Switch - The Cyborg Digital Reverb pedal includes Rocktron

Patented Digital HUSH noise reduction. Select “ON” if the reverb pedal is

placed after a noisy distortion pedal. Select “OFF” when using clean tones.

For more on the HUSH and how it works, see the HUSH Section of this

manual.

Descriptions

Preset Select/Store Switch and Store LED - this switch allows you

scroll through the presets by using the footswitch. Press and depress the

Preset Select Footswitch to change the preset. Note that the presets will

change in order from 1 to 8. After preset 8, the preset will go back to

preset 1.

STORE function - Use this function to STORE (or save) changes you

have made to a preset. To operate the STORE function, press and hold

the PRESET SELECT switch down for 2 seconds. This will save the

changes to your preset. The STORE LED will “hold on” and then return

to flashing to confirm the storing process has been completed.

On/Off Footswitch and LED - this footswitch is used to turn “ON” or

“OFF” the Cyborg Reverb. When the LED is lit , the reverb is “ON”

Output Jack - Using a standard guitar cable with a 1/4” jack, plug into

your amplifier or the next effect pedal in your signal chain.

MIDI Jack - Using the Rocktron MIDI Breakout Cable (sold separately)

you can connect the Cyborg Pedal to a Rocktron MIDI Footcontroller

such as the Rocktron MIDI XChange, MIDI Mate or All Access. This

feature allows you to access all 64 presets and even connect other Cyborg

pedals to be controlled by the MIDI footcontroller.

Descriptions Continued

Other manuals for Cyborg

This manual suits for next models

Table of contents

Other Rocktron Music Pedal manuals

Rocktron

Rocktron Mega Booster User manual

Rocktron

Rocktron Reaction Digital Delay User manual

Rocktron

Rocktron Short Timer Retro Digital Delay User manual

Rocktron

Rocktron Celestial Delay User manual

Rocktron

Rocktron XCHANGE User manual

Rocktron

Rocktron Reaction Super Booster User manual

Rocktron

Rocktron HUSH 2X User manual

Rocktron

Rocktron O.D.B. User manual

Rocktron

Rocktron XTUNE User manual

Rocktron

Rocktron Sweet Spot User manual

Rocktron

Rocktron VII Deadly Sins User manual

Rocktron

Rocktron CLASSIC WAH PEDAL User manual

Rocktron

Rocktron BIG CRUSH User manual

Rocktron

Rocktron TRUE BYPASS Tru-Loop User manual

Rocktron

Rocktron HYPNOTIC FLANGE User manual

Rocktron

Rocktron Reaction Octaver User manual

Rocktron

Rocktron HUSH User manual

Rocktron

Rocktron Reaction Phaser User manual

Rocktron

Rocktron UTOPIA G100 User manual

Rocktron

Rocktron Third Angel Distortion User manual

Rocktron

Rocktron Valve Charger User manual

Rocktron

Rocktron RAMPAGE User manual

Rocktron

Rocktron MicroHUSH User manual

Rocktron

Rocktron Reaction Distortion 1 User manual

Popular Music Pedal manuals by other brands

Behringer

Behringer ULTRA WAH UW300 manual

Whirlwind

Whirlwind oc-bass quick start guide

Strymon

Strymon Lex-rotary user manual

Behringer

Behringer PB600 manual

Lexicon

Lexicon MX200 user guide

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series quick start guide

Matthews Effects

Matthews Effects Whaler V2 manual

Grid 1

Grid 1 Pedal Jeanie user manual

Amptweaker

Amptweaker tightboost user manual

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro owner's manual

PuzzleSounds

PuzzleSounds DR. Q ENVELOPE FILTER manual

BYOC

BYOC Analog Chorus Build instructions

Dimavery

Dimavery EPVP-50 manual

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ operating manual

Pro-MIDI

Pro-MIDI G25 user manual

DW 7000 owner's manual

FAMC

FAMC Liquid-Foot Jr. Series user manual

Dimavery

Dimavery EPOD-50 Overdrive user manual