ROBOTIQ AX Series User manual

Palletizing Solution

AX Series

INSTALLATION GUIDE

X-990105-G

THANK YOU FOR CHOOSING ROBOTIQ

This step-by-step guide will allow you to install and test your Robotiq Palletizing Solution

on Universal Robots. Visit the elearning.robotiq.com to see the video of the installation

steps.

1. WHAT IS SUPPLIED?

Standard upon delivery of SOL-PAL-UR-VAC-1500 and SOL-PAL-UR-1500*:

•Palletizing Solution base including:

▪1 x Linear axis (1500 mm stroke)

▪1 x Linear axis Controller

▪4 x Pallet sensors

▪2 x Status lights

▪1 x Cable management system

•6 x Concrete anchors

•1 x Box detection sensor

•1 x PowerPick Vacuum Gripper kit (Optional)

•1 x Air ﬁlter kit (optional)

•1 x Set of four (4) casters

•1 x Material Handling Copilot software license dongle

*SOL-PAL-UR-1500 does not contain the gripper, and as such the gripper installation steps do not apply.

2. SAFETY & WARNINGS

The operator(s) must have read and understood all of the Safety section in the user manual

(available at support.robotiq.com).

The entire cell must go through a comprehensive risk assessment process before it can be used.

Do not operate the Palletizing Solution or even turn on the power supply before the device is

ﬁrmly anchored and the machine area is cleared. Make sure the air supply is secured.

Make sure to follow all safety rules and regulations of your workplace. Always wear all

recommended personal protective equipment in accordance with your workplace safety

standards.

Failure to properly secure and install the equipment can result in material damage and bodily

injury.

3. TOOLS NEEDED

Included

Not included

•12.7 mm concrete drill bit (1/2 in) (for

use with a rotary hammer)

•19mm Socket (10 mm drive size)

•17mm Socket (10 mm drive size)

•2 mm hex key

•3 mm hex key

•4 mm hex key

•5 mm hex key

•6 mm hex key

•10 mm hex key

•Optional:

• 2.5 mm hex key

• 5.5-17 mm double ended wrench

• 20-21 mm double ended wrench

•Lifting equipment (min. capacity of

200 kg)

•Power screwdriver

•Drill with a No.2 Phillips bit

•2.5 mm slotted screw- driver

•Tube cutter

•Ratcheting socket wrench with 10mm

(3/8 in) drive or adapter

•Torque wrench with 10mm (3/8 in)

drive or adapter

•Isopropyl alcohol

•Hammer drill

•Hammer

4. UNBOXING

The transport, lifting and moving of the Palletizing Solution should be done by qualiﬁed

and authorized personnel. Failure to do so may result in machine damage, serious injuries

or death.

Crush hazard: Keep your hands and body parts clear when lowering the column onto the

base. Failure to do so could result in serious injuries or death.

1. Remove the top panel and the four (4) sides of the crate by removing the screws that

hold them into place.

2. Remove the upper wooden frame by removing the screws that hold it into place.

3. Cut and remove the strapping material.

4. Remove the linear axis controller.

5. Remove the two (2) bolts that hold the base to the crate.

6. Take the base out of the crate.

7. Take all cardboard boxes out of the crate.

8. Remove the screws that hold the lower wooden frames to the crate.

9. Remove the lower wooden frames.

10. Unscrew the two (2) bolts that hold the column to the crate; discard the metal plate.

11. Remove the screws that hold the piece of wood under the foot base.

12. Lift the foot base, remove the piece of wood and lower the foot base slowly and carefully

(see image below).

13. Position the column vertically. Use the pivot point at the base to lift the column.

14.Lift and place the column onto the base. Robotiq recommends attaching the hook at

the top of the column to a lifting device (e.g., hoist) to bring the column upright (column

weight =88 kg / 194 lb).

15. Secure the column on the base using the four (4) M10 screws provided. Tighten to a

torque of 50 Nm (37 ft-lb).

To securely move and position the unit, there are two possibilities:

Using a forklift

Pay attention to the center of gravity to prevent the equipment from falling.

Make sure to secure and stabilize the Solution before any move.

Using the set of wheels provided with the Solution

1. Screw the four (4) provided leveling

bolts to lift the solution (about 1

centimeter high).

2. Secure the four (4) wheels using the

provided screws.

3. Unscrew the four (4) bolts to get the

solution down on its wheels.

Do not work on the Solution while

it is on its wheels as it is not

stable. To return the Solution on

its feet, simply screw the four

bolts, remove the wheels and

unscrew the bolts.

5. MECHANICAL & ELECTRICAL INSTALLATION

Main steps

A. Robot Installation

B. Base Cover Plate Removal

C. Linear Axis Controller Installation

D. Universal Robots Controller Installation

E. Power Cables Connection

F. Inter-Controller Cables Connection

G. Status LED Connection

H. Pallet Sensors and Palletizer Base Cable Routing

I. Safety Signals Connection

J. Solution Centering

K. PowerPick Vacuum Gripper Installation (Optional)

L. PowerPick Controller Installation

M. Cable Routing System Installation

N. PowerPick Gripper and Copilot Connection

O. Box Sensor(s) Cable Connection

P. Palletizer and Surrounding Equipments Positioning

Q. Solution Anchoring

R. Finalization and Power On

S. Joint Limits Setting

For details of each step, refer to the corresponding section below.

Install the robot before installing the linear axis controller in order to ensure the

stability of the Palletizing Solution.

A. Robot Installation

1. Place the robot on the robot base plate so its power cable is

oriented towards the linear axis. Align properly with the two

dowel pins (already installed on the robot base), and secure

the robot using four (4) M8 x 25 mm screws and Belleville

washers. The required torque value is 20 Nm (15 ft-lb).

2. Unclip the two mounting brackets of the cable management system: one on the

column and one on the carriage.

3. Push the robot power cable into the cable carrier up to the column. There are two

separate raceways; one for the air tube and the other for the robot power cable.

The robot power cable and the air tube should not use the same section. Do not

channel the cable through the column just yet.

B. Base Cover Plate Removal

Remove the cover plate for cable management.

C. Linear Axis Controller Installation

1. Remove the four (4) screw caps on the linear axis controller.

2. Partially unscrew (approximately 3 mm) each screw at the back of the linear axis

controller.

3. Lower the linear axis controller slowly and carefully.

4. Tighten the screws to secure the controller to the controller bracket. The torque

required is 15 Nm (11 ft-lb).

D. Universal Robots Controller Installation

1. Remove the four screws on the top of the linear axis controller.

2. Place the UR controller on top of the linear axis controller and secure it

with the four screws previously removed.

Do NOT connect the UR controller’s power cable to the UR controller.

E. Power Cables Connection

Refer to the linear axis & controller nomenclature summary below for next steps.

The Solution should only be connected to a power source

once all connections have been made and completed.

1. Connect the power cable of the linear axis controller to the

UR controller.

2. Push the robot's power cable into the column via the hole

on the side and bring it out through hole #2.

3. Connect the robot power cable to the UR controller.

4. Connect the Teach Pendant to the UR controller.

5. Connect the power cable of the UR controller to the linear axis controller. Insert it

through hole #4.

6. Continue to channel the cable through the column and the base and bring it out from

the other end of the base. Do not connect the power cable to a power source just yet.

F. Inter-Controller cables Connection

1. Open the UR controller. Connect the USB hub to a USB port.

2. Connect the Ethernet/USB converter cable to a USB port.

3. Connect the Ethernet cable into the Ethernet socket on top of the linear axis controller.

4. Push the other end of the Ethernet cable through the hole under the UR controller and

connect it to the Ethernet/USB converter cable that is already connected.

G. Status LED Connection

1. Channel the status LED cables (W70 and W80) through the column and pull them

out via hole #3.

2. Connect both status LED cables (W70 and W80) to the linear axis controller.

Follow cable labeling and connector identiﬁcation.

H. Pallet Sensors and Palletizer Base Cable Routing

1. Channel the pallet sensor cables (W50 and W60) through the column and pull them out

via hole #3.

2. Connect the pallet sensor cables to the linear axis controller. Follow cable labeling and

connector identiﬁcation.

3. Push the linear axis cable into the column via hole #4 and bring it out at the front of the

column.

4. Connect the linear axis cable to the linear axis.

Other manuals for AX Series

This manual suits for next models

Table of contents

Other ROBOTIQ Robotics manuals

ROBOTIQ

ROBOTIQ POWERPICK20 Operation and maintenance manual

ROBOTIQ

ROBOTIQ EPick User manual

ROBOTIQ

ROBOTIQ 2F-85 User manual

ROBOTIQ

ROBOTIQ CNC Machine Tending Kit User manual

ROBOTIQ

ROBOTIQ 2F-85 Operation and maintenance manual

ROBOTIQ

ROBOTIQ 2-Finger Adaptive Robot Gripper - 200 User manual

ROBOTIQ

ROBOTIQ HAND-E Series User manual

ROBOTIQ

ROBOTIQ PE Series User manual

ROBOTIQ

ROBOTIQ AirPick Operation and maintenance manual

ROBOTIQ

ROBOTIQ FT 300-S User manual

ROBOTIQ

ROBOTIQ PowerPick Vacuum Gripper User manual

ROBOTIQ

ROBOTIQ Wrist Camera User manual

ROBOTIQ

ROBOTIQ AirPick User manual

ROBOTIQ

ROBOTIQ PE Series Operation and maintenance manual

ROBOTIQ

ROBOTIQ PE20 User manual

ROBOTIQ

ROBOTIQ HAND-E User manual

ROBOTIQ

ROBOTIQ PALLETIZING SOLUTION AX Series User manual

ROBOTIQ

ROBOTIQ AX Series User manual

ROBOTIQ

ROBOTIQ PE20 User manual

ROBOTIQ

ROBOTIQ HAND-E User manual

ROBOTIQ

ROBOTIQ EPick User manual

ROBOTIQ

ROBOTIQ EPick User manual

ROBOTIQ

ROBOTIQ 85 User manual

ROBOTIQ

ROBOTIQ Finishing Kits User manual

Popular Robotics manuals by other brands

STEMCenter USA

STEMCenter USA Pi-Bot v2.00 user manual

SunFounder

SunFounder PiDog manual

Universal Robots

Universal Robots UR5 Service manual

Universal Robots

Universal Robots E Series Original instructions

YASKAWA

YASKAWA MOTOMAN-MPL80 II instructions

EFORT

EFORT ECR5 Quick start manual

Epson

Epson C8 Series MANIPULATOR MANUAL

WowWee

WowWee ROBOQUAD user manual

Milvus Robotics

Milvus Robotics SEIT 100 user manual

RoboMaster

RoboMaster AI Robot 2020 Standard Version user manual

fischertechnik

fischertechnik Mini Bots manual

YASKAWA

YASKAWA MA2010 Operating and maintenance instructions

Abicor Binzel

Abicor Binzel iCAT mini operating instructions

ABB

ABB OmniCore E10 product manual

YASKAWA

YASKAWA Motoman DX200 instructions

pitsco

pitsco Tetrix Max Creator's Guide

ECOVACS

ECOVACS DEEBOT R95 instruction manual

Feng Yuan

Feng Yuan Interstellar Warrior user guide