Roberts 10-63 User manual

13" Multi-Floor Cutter

OWNER’S MANUAL

Coupeuse à planchers multiples de

330mm

MANUEL D’UTILISATION

Cortador para múltiples pisos de

330mm

MANUAL DE OPERACIÓN

10-63

WARNING Read and understand all instructions. Failure to follow all instructions may result in serious

bodily injury. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

AVERTISSEMENT Lire et comprendre toutes les directives. Le non-respect des directives peut causer des

blessures graves.VEUILLEZ CONSERVER CES DIRECTIVES POUR RÉFÉRENCE ULTÉRIEURE.

ADVERTENCIA Lea y comprenda todas las instrucciones. Si no se cumplen todas las instrucciones a puede

producir lesiones físicas graves. CONSERVE ESTAS INSTRUCCIONES PARA CONSULTARLAS EN EL FUTURO.

- 1 -

SAFETY RULES

WARNING! FAILURETO FOLLOWTHESE RULES MAY RESULT IN SERIOUS

INJURY! USINGTHIS MACHINEWITH RESPECT AND CAUTION WILL

CONSIDERABLY LESSENTHE POSSIBILITY OF PERSONAL INJURY.

1. READ AND UNDERSTANDTHIS INSTRUCTION MANUAL BEFORE OPERATING

THE 13"MULTI-FLOOR CUTTER.

2. If you are not thoroughly familiar with the operation of the 13" Multi-Floor

Cutter, obtain advice from a qualiﬁed instructor or call 866-435-8665.

3. Stay alert. Do not operate while under the inﬂuence of drugs, alcohol, or

medication.

4. Always wear safety approved eye protection with side shields (ANSI Z87.1).

5. Keep work area clean and free of debris.

6. Keep children and unauthorized persons away from the 13" Multi-Floor Cutter

and work area.

7. Make sure tool is secure. Operate only on a ﬁrm substrate or solid stand.

8. Use the right tool. Do not force the 13" Multi-Floor Cutter or use it for a job for

which it was not designed; use only on approved materials.

9. Keep blade sharp. A dull blade will not perform properly.

10. Always keep hands away from blade while operating or carrying.

11. Do not alter or misuse this tool. The 13" Multi-Floor Cutter is precision built;

modiﬁcations not speciﬁed in this manual may result in a dangerous condition.

12. Maintain the 13" Multi-Floor Cutter with care. Keep blade sharp and clean.

Follow instructions for lubricating and changing accessories.

13. Use only recommended accessories. The use of improper accessories may

cause hazards or injury.

14. Never leave the 13" Multi-Floor Cutter unattended. Secure the handle with the

lock chain when not in use.

15. Warning: The dust generated by cutting certain wood, wood ﬁber and / or PVC

products can be harmful to your health.

- 2 -

ASSEMBLY

Assemble the table assembly (Fig.

1-A) Fig.1 to the blade assembly

(Fig. 1-B) using 4 small Phillips head

screws (Fig. 1-C) to secure the top of

the table. Use two larger pan head

screws (Fig.1-D) to secure the table

brace.

Assemble the handle (Fig. 2-A) to

the top of the blade assembly. First,

loosen the three ﬁxing screws (Fig.

2-B) using a hex key. Insert the

handle shaft into the cylindrical hole

(Fig. 2-C), make sure the recessed

hole (Fig. 3-D) lines up with the

center screw. Once properly aligned

and inserted, tighten the center ﬁxing

screw using a hex. key. Then tighten

the other two ﬁxing screws.

SETTING UP FOR OPERATION

The laminate ﬂooring cutter is

shipped with the blade assembly

in the down and locked position.

This safety feature ensures that

the cutting edge of the blade is not

exposed during transport or storage.

To unlock the blade assembly, loosen

the safety lock knob (Fig. 3-A),

depress the handle then slide the

lock knob to the right to disengage

the lock (Fig. 3-B).

WARNING Secure handle in the

down position and re-engage the

safety lock before storing, carrying or

transporting your laminate ﬂooring

cutter.

SET UP

FIGURE 1

FIGURE 2

FIGURE 3

- 3 -

CUTTING

CUTTING PREPARATION

Adjust the angle attachment to

desired angle as needed (Fig. 4-A,B).

The angle attachment can be used

on left side of the table (Fig. 4).

WARNING Do not put your ﬁngers

against the sharp edge of the blade

at any time.

STRAIGHT CUTTING

Insert material between the cutting

blade and the base, ﬂush with the

angle attachment (Fig. 5) and hold

the material with foot then push

handle down to complete a cut.

WARNING Maintain control of the

handle. Do not allow handle to slam

back after making cut.

45º CUTTING

Swing the angle attachment to 45°.

Insert material between the cutting

blade and the base, against the

angle attachment (Fig. 5), then push

the handle down to complete a cut.

WARNING Maintain control of the

handle. Do not allow handle to slam

back after making cut.

WARNING Do not put your ﬁngers

against the sharp edge of the blade

at any time.

FIGURE 4

FIGURE 5

- 4 -

BLADE ADJUSTMENT

ADJUSTINGTHE BLADE

1. Unscrew and remove the

adjustment plate screws (Fig. 6).

2. Tighten both adjustment plates

by 1 or 2 holes (Fig. 7).

NOTE: The pitch on each lifting

screw is .125mm. The adjustment

on both plates must be the same.

3. Cut a piece of paper to ensure the

tool is set correctly (Fig. 8).

CUT GUIDE

Your tool cuts a wide variety of

products. Please refer to this cut

guide for recommended products

and thicknesses.

• Laminate Flooring ................13mm

• Vinyl Composite Tile ............13mm

• Soft Plastic ............................13mm

• Vinyl Siding...........................13mm

• Fiber Cement Siding ............13mm

FIGURE 6

FIGURE 7

FIGURE 8

- 5 -

HONING BLADE

Removing burrs from the ﬂat edge of the

blade is very important, honing a new blade

should be done after the ﬁrst 40-100 cuts,

after every 100+ cuts and when the blade

has been re-sharpened.

With the blade (Fig. 9-B) installed and

positioned roughly 1/8" above the table top,

lay the ﬂat side of your honing stone (Fig.

9-A) against the ﬂat side of the blade. Move

the honing stone from one end to the other

a few times until burr has been removed.

SHARPENING OR REPLACING BLADE

The included blade can be sharpened.

Only the beveled edge of the blade must

be sharpened. The ﬂat edge of the blade

must remain ﬂat. We recommend that

this operation be done by a qualiﬁed

professional.

WARNING Blade is very sharp. Wear

gloves when handling blade.

1. To remove the blade (Fig. 10-A), remove

the seven allen head screws (Fig. 10-B)

using the supplied hex. key. Carefully

remove the blade.

2. Once blade has been sharpened or

replaced, it can be re-installed. Position

the blade (Fig. 11-1) with its ﬂat edge

facing the table (Fig. 11-B). Make sure

the mounting surface and blade are

clean, re-install the blade with the seven

allen head screws removed earlier using

the supplied hex key.

LUBRICATION

To prevent surface corrosion, it is

recommended to apply a small amount of

light machine oil on the sliding parts of the

laminate cutter. Lubrication should be done

once every two months or once a month if

working in dirty or dusty conditions.

MAINTENANCE

FIGURE 9

FIGURE 10

FIGURE 11

- 6 -

EXPLODED PARTS DIAGRAM

- 7 -

PARTS LIST

NO. DESCRIPTION Q TY.

1 Plastic end cap 2

2 Cap screw 2

3 Guide sleeve 2

4 Cam 4

5 Camshaft 1

6 Round hd allen screw 3

7 Stop knob 1

8 Stop block 1

9 Round hd allen screw 7

10 13" HSS Blade 1

11 Pan hd screw 2

12 Countersunk screw 4

13 Set screw 4

14 Guiding rod 2

15 Spring 2

16 Upper body 1

17 Knob 1

18 Washer 2

19 Angle guage 1

20 Handle 1

21 Handle grip 1

22 Countersunk hd screw 2

23 Washer 2

24 Spring washer 8

25 Angle pointer 1

26 Round hd allen screw 1

27 Work table 1

28 Rubber foot 2

29 Countersunk hd screw 4

30 Adjustable plate 2

31 Pan hd screw 4

32 Lower body 1

33 Work table support 1

34 Work table foot 1

35 Round hd phillips screw 2

36 Countersunk hd screw 4

- 8 -

RÈGLES DE SÉCURITÉ

AVERTISSEMENT: LA NON-OBSERVATION DE CES RÈGLES PEUT

ENTRAINER DE GRAVES BLESSURES! L’UTILISATION DE CET APPAREIL

AVEC RESPECT ET PRUDENCE DIMINUERA CONSIDÉRABLEMENT LA

POSSIBILITÉ DE BLESSURES CORPORELLES.

1. LISEZ ET COMPRENEZ BIEN LE MANUEL D’UTILISATION AVANT D’UTILISER LA

COUPEUSE À PLANCHERS MULTIPLES DE 330MM.

2. Si vous n’êtes pas complètement familier avec le fonctionnement du Coupeuse

à planchers multiples de 330mm, demandez conseil à un instructeur qualiﬁé ou

appelez le 866-435-8665.

3. Soyez vigilant. N’utilisez pas l’appareil sous l’effet de drogues, d’alcool ou de

médicaments.

4. Portez toujours des lunettes de sécurité homologues avec des ceillères (ANSI Z87.1).

5. Maintenir votre zone de travail propre et sans débris.

6. Gardez les enfants et les personnes non-autorisées hors de portée du Coupeuse

à planchers multiples de 330mm et de la zone de travail.

7. Assurez-vous que l’outil est sécuritaire. Utilisez-le uniquement sur une surface

dure ou un support ferme.

8. Utiliser le bon outil. Ne forcez pas le Coupeuse à planchers multiples de 330mm

ou ne l’utilisez pas pour une tache pour laquelle il n’a pas été conçu; utilisez

uniquement sur des matériaux approuvés.

9. Maintenir la lame aiguisée. Une lame émoussée ne coupera pas correctement.

10. Garder les mains loin de la lame lorsque vous l’utilisez ou la transporter.

11. Ne modiﬁez pas ou n’utilisez abusivement cet outil. Le Coupeuse à planchers

multiples de 330mm est fabriqué avec précision; les modiﬁcations non

spéciﬁées dans ce manuel d’utilisation peuvent créer des conditions d’utilisation

dangereuses.

12. Entretenez le Coupeuse à planchers multiples de 330mm avec soin. Maintenez

la lame aiguisée et propre. Respectez les consignes de lubriﬁcation et de

changement des accessoires.

13. Utilisez uniquement les accessoires recommandés. L’utilisation d’accessoires

inappropriés peut créer des dangers ou provoquer des blessures.

14. Ne laizzez jamais le Coupeuse à planchers multiples de 330mm sans

surveillance. Verrouillez la poignée avec le verrou de sécurité lorsque le

Coupeuse à planchers multiples de 330mmn’est pas utilisé.

15. Avertissement: la poussière générée par la coupe de certains type de bois, de

ﬁbres de bois ou de produits de PVC peut être dangereux à votre santé.

- 9 -

ASSEMBLY

Assemblez l’ensemble de la table

(Fig. 1-A) au châssis de coupe (Fig.

1-B). Pour ﬁxer le haut de la table,

utilisez quatre petite vis à tête Phillips

(Fig. 1-C). Pour ﬁxer le support de la

table, utilisez deux vis à tête bombée

(Fig. 1-D).

Assemblez le manche (Fig. 2-A)

au dessus du châssis de coupe.

Premièrement, en utilisant une clé

hexagonale, desserrez les trois vis de

ﬁxation (Fig. 1-B). Ensuite insérez la

tige du manche à l’intérieur du trou

de montage (Fig. 2-C), s’assurant

que le trou d’alignement (Fig. 2-D)

s’aligne avec la vis de ﬁxation du

centre. Une fois que le manche est

aligné et inséré, serrez la vis de

ﬁxation du centre. Finalement, serrez

les deux autres vis de ﬁxation.

SETTING UP FOR OPERATION

Le coupe de sol stratiﬁé est expédié

avec l’ensemble de couteau abaissé

et en position verrouillé. Cette

caractéristique de sécurité veille à

ce que le tranchant du couteau n’est

pas exposé au cours du transport ou

de l’entreposage. Pour déverrouiller

l’ensemble de couteau, desserrez le

bouton de verrouillage de sécurité

(Fig. 3-A), appuyez légèrement sur le

manche, puis faites glisser le bouton

de verrouillage vers la droite pour

dégager le verrou (Fig. 3-B).

Attention Fixez le manche en

position basse et ré-enclenchez le

verrou de sécurité avant de le ranger,

le port ou le transport de votre coupe

de sol stratiﬁé.

ASSEMBLAGE

FIGURE 1

FIGURE 2

FIGURE 3

Table of contents

Languages:

Other Roberts Cutter manuals

Roberts

Roberts 10-68 User manual

Roberts

Roberts 10-60 User manual

Roberts

Roberts 10-146 User manual

Roberts

Roberts 10-152 User manual

Roberts

Roberts 10-95 User manual

Roberts

Roberts 10-91 User manual

Roberts

Roberts 10-35 User manual

Roberts

Roberts 10-66 User manual

Roberts

Roberts 10-900 User manual

Roberts

Roberts 13 PRO User manual

Roberts

Roberts 10-60 User manual

Popular Cutter manuals by other brands

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Original instructions

Makita

Makita DCS552 instruction manual

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 user manual

Makita

Makita 4112HS instruction manual

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S manual

Hitachi

Hitachi CM 4SB2 Safety instructions and instruction manual

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 instruction manual

GCC Technologies

GCC Technologies AFJ-24S user manual

DeWalt

DeWalt XR LI-ION DCS350N manual

Baudat

Baudat ES1 instruction manual

Mafell

Mafell ZAF 200 Operating instructions and spare parts list

Makita

Makita 4100NH instruction manual

Formax

Formax FD 574 Operator's manual

EINHELL

EINHELL TE-MA 1500 Original operating instructions

Husqvarna

Husqvarna Cut-n-Break K 760 Operator's manual

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Operator's manual

TRI tool

TRI tool 301A user manual

Roller

Roller King 1 1/4 operating instructions